Advantech FPM-7000T Series User manual

User Manual
FPM-7000T Series
True-flat Industrial Monitor with
5-wire Resistive Touchscreen,
Direct-VGA/DP ports

FPM-7000T Series User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2015
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
This Manual Covers the Following Models.
FPM-7061T-XXXX
FPM-7121T-XXXX
FPM-7151T-XXXX
Part No. xxxxxxxxxxxxx Edition 1
Printed in China September 2015

iii FPM-7000T Series User Manual
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.

FPM-7000T Series User Manual iv
Declaration of Conformity
This device complies with part 15 of the FCC rules: Operation is subject to the follow-
ing two condition:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Technical Support and Assistance
1. Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

v FPM-7000T Series User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to the
user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. The sound pressure level at theoperator's position according to IEC 704-1:1982
is no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

FPM-7000T Series User Manual vi

vii FPM-7000T Series User Manual
Contents
Chapter 1 General Information ............................1
1.1 Introduction ...............................................................................................2
1.2 Specifications............................................................................................2
1.2.1 General.........................................................................................2
1.2.2 Touchscreen.................................................................................2
1.3 LCD Specification......................................................................................3
1.4 Power Consumption..................................................................................4
1.5 Connectors................................................................................................4
1.6 Dimensions ...............................................................................................5
Figure 1.1 FPM-7061T Dimensions.............................................5
Figure 1.2 FPM-7121T Dimensions.............................................6
Figure 1.3 FPM-7151T Dimensions.............................................7
1.7 Power Connector Bracket .........................................................................8
Chapter 2 Mounting ..............................................9
2.1 Mounting the Monitor ..............................................................................10
2.1.1 Wall Mounting with FPM-1000T-SMKE ......................................10
Figure 2.1 Wall Mounting...........................................................10
2.1.2 Panel Mounting...........................................................................11
2.1.3 VESA Mount for FPM-7000T......................................................12
Figure 2.2 Desktop Stand..........................................................12
Figure 2.3 VESA mount for FPM-7061T....................................13
Figure 2.4 VESA 100 mount for FPM-7121T/7151T..................14
Figure 2.5 VESA 75 mount for FPM-7121T/7151T....................14
Appendix A OSD Operation Keypad.......................1
A.1 OSD Board Overview (FPM-71x1T)..........................................................2
A.1.1 OSD Key Functions ......................................................................2
A.2 OSD Board Overview (FPM-7061T) .........................................................8
A.2.1 OSD Key Functions ......................................................................9
A.3 Installing Drivers for Windows OS...........................................................13
Appendix B Setting Serial Data for Expansion....15
B.1 Setting Serial Data for Expansion...........................................................16
B.2 Touch screen RS232 Connector Pin Definition.......................................17

FPM-7000T Series User Manual viii

Chapter 1
1General Information
Sections include:
Introduction
Specifications
LCD Specification
Power Consumption
Connectors
Dimensions

FPM-7000T Series User Manual 2
1.1 Introduction
Advantech's FPM-7000T is a true-flat TFT LCD flat panel monitor built specifically for
industrial applications. With the its touchscreen, FPM-7000T is an excellent and
user-friendly system control interface.
In addition to its usual application as an LCD panel monitor, FPM-7000T comes
standard with direct VGA/DP signal inputs, making it compatible with Industrial PCs
and Workstations. Its OSD (On rear cover) function allows you to adjust display fac-
tors such as brightness, contrast, colours and VGA signal information. Functions that
are more and more critical as HMI users become aware of the benefits of flat panel
monitors. The rear cover is of SECC steel, and the front panel is of die-cast magne-
sium alloy with IP66 certification.
With a new system design, this monitor can support operating temperatures from -20
~ 60°C for a variety of environments. Designed with various mounting methods for
users to apply into the system or adopt to the environment easily.
1.2 Specifications
1.2.1 General
Construction: Die-cast Magnesium alloy front bezel and SECC rear cover
Front panel: IP66 certified
Control: OSD control pad on rear
Mounting: Panel, wall, desktop, VESA
Dimensions (W x H x D):
–FPM-7061T: 199.0 x 152.0 x 46.10 mm
–FPM-7121T: 311.8 x 238 x 44.5 mm
–FPM-7151T: 383.2 x 307.3 x 48.0 mm
Weight:
–FPM-7061T: 1.2 kg
–FPM-7121T: 2.6 kg
–FPM-7151T: 4.2 kg
1.2.2 Touchscreen
Type: 5-wire Resistive Touch
Controller:
–USB interface for FPM-7061T
–USB & RS-232 interface for FPM-7121T & FPM-7151T
OS Support: Microsoft® Windows XP, Vista,7,8, and Linux
Linux support version please check PenMount Website:
http://www.penmount.com/down_2_1.php

3 FPM-7000T Series User Manual
Chapter 1 General Information
1.3 LCD Specification
FPM-7061T
Display Type: VGA LED LCD
Display Size: 6.5"
Max. Colors: 262K
Max. Resolution: 640 x 480
View Angle: 160° (V), 140° (H)
Luminance: 800 cd/m2
Storage Temperature: -40 ~ 85°C
Operating Temperature: -30 ~ 80°C
Contrast Ratio: 600:1 (typical)
Lamp Life Time (MTBF): 50,000 hrs.
FPM-7121T
Display Type: XGA LED LCD
Display Size: 12.1"
Max. Colors: 16.2 M
Max. Resolution: 1024 x 768
View Angle: 160° (V), 140° (H)
Luminance: 600 cd/m2
Storage Temperature: -40 ~ 85°C
Operating Temperature: -30 ~ 80°C
Contrast Ratio: 700:1 (typical)
Lamp Life Time (MTBF): 50,000 hrs.
FPM-7151T
Display Type: XGA LED LCD
Display Size: 15"
Max. Colors: 16.7 M
Max. Resolution: 1024 x 768
View Angle: 160° (V), 140° (H)
Luminance: 400 cd/m2
Storage Temperature: -40 ~ 85°C
Operating Temperature: -30 ~ 80°C
Contrast Ratio: 700:1 (typical)
Lamp Life Time (MTBF): 50,000 hrs.
Note! There might be several bright or dark pixels on the LCD. This phenome-
non is normal in today's LCD manufacturing. Inspection criteria are fol-
lowing specifications defined by LCD vendor.
Note! Section 1.3 specifications are for LCD only.
Please refer to system specification for operating & storage tempera-
tures

FPM-7000T Series User Manual 4
1.4 Power Consumption
Max Power consumption:
–FPM-7061T: 10 W ± 20%
–FPM-7121T: 18 W ± 20%
–FPM-7151T: 16 W ± 20%
Power input: Phoenix Jack: 24 VDC ± 20%
Safety Standards: BSMI, CE, FCC, CCC, UL
1.5 Connectors
The following connectors are situated on FPM-7000T Series:
VGA Port (DB-15)
This DB-15 connector can be connected to the system via the external 15-pin
DB-15 connector located on the left side of the system unit.
DP or HDMI port
Connected with a standard DP or HDMI connector thru I/O port of this unit. Only
supports digital signals
Touchscreen Connector (DB-9)
This connector will be present only if a touchscreen is installed. It must be con-
nected to the RS-232 port of the PC. The touchscreen cable is included with all
orders which include the touchscreen option.
Touchscreen Connector (USB)
This connector will be present only if a touchscreen is installed. It must be con-
nected to the USB port of the PC. The touchscreen cable is included with all
orders which include the USB touchscreen option.
Plug-In Block 3P Male (ME050-50803) DC 24 V
This block connector can be connected via the external plug-in block 3P with
flanges Female MC211-F103 connector
Note! RS-232 & USB touchscreen interface allow connection into the system
at the same time, but USB interface has higher priority. Also be noted
that when using USB touch interface and switch to RS-232 interface, it
need to restart your industrial PCs or workstation.

5 FPM-7000T Series User Manual
Chapter 1 General Information
1.6 Dimensions
Figure 1.1 FPM-7061T Dimensions

FPM-7000T Series User Manual 6
Figure 1.2 FPM-7121T Dimensions

7 FPM-7000T Series User Manual
Chapter 1 General Information
Figure 1.3 FPM-7151T Dimensions

FPM-7000T Series User Manual 8
1.7 Power Connector Bracket

Chapter 2
2Mounting
Wall Mounting
Panel Mounting
Desktop Mounting
Swing Arm Mounting

FPM-7000T Series User Manual 10
2.1 Mounting the Monitor
The FPM-7000T Series can be mounted in many different ways. The versatility of the
FPM-7000T enable it to be mounted on your desk or anywhere else.
2.1.1 Wall Mounting with FPM-1000T-SMKE
The FPM-7000T can be mounted directly on a wall with panel mounting brackets.
Please refer to Figure 2.1 and follow the following steps to mount FPM-7000T on a
wall:
Figure 2.1 Wall Mounting

11 FPM-7000T Series User Manual
Chapter 2 Mounting
2.1.2 Panel Mounting
1. Position the FPM against the panel
2. Insert the clamps into the side of the FPM
3. Secure the clamp to the panel using the included screws.

FPM-7000T Series User Manual 12
2.1.3 VESA Mount for FPM-7000T
2.1.3.1 Desk top stand with FPM-1000T-SMKE Kit
The FPM-7000T can be mounted as a stand on the desk by additional mounting
brackets. See figure 2.2 below for reference.
Figure 2.2 Desktop Stand