Agora Models LAMBORGHINI MIURA Pack 12 Manual

The “Automobili Lamborghini” and “Automobili Lamborghini Bull and Shield” trademarks, copyrights,
designs and models are used under number from Automobile Lamborghini S.p.A, Italy.
STAGE 92: FITTING THE REAR
NUMBER PLATE AND GRILLE
STAGE 93: ASSEMBLING THE
BOOT COMPARTMENT AND
INSTALLING THE REAR LIGHTS
STAGE 94: FITTING THE
WINDOW GRILLE AND THE
BOOT COMPARTMENT
STAGE 95: FITTING THE REAR
BODY AND WHEEL ARCHES
STAGE 96: ATTACHING THE
WHEELS AND ADDING THE
BERTONE LOGO
STAGE 97: ADDING THE
BATTERY COMPARTMENT
AND THE SHIELD EMBLEM
STAGE 98: FITTING THE
TAILPIPES AND CONNECTING
THE ELECTRICS
STAGE 99: PREPARING THE
WINDSCREEN
STAGE 100: ATTACHING THE
FRONT BODY, THE SIDE
SKIRTS, THE NUMBER PLATE
AND ADDING DETAILS
INSTALLING THE BATTERIES
AND OPERATING THE
ELECTRICS
Pack 12
BUILD INSTRUCTIONS

AGORAMODELS LAMBORGHINI MIURA
2
Spare screws are included with each part. Occasionally, you may be instructed to keep spare or
unused screws for a later stage. Keep these spares in a safe place and label them correctly.
Please make sure you don’t mix up the screws. They look quite similar, but the threads do vary
slightly. Using the wrong screws may damage the parts.
When securing parts together using multiple screws, fit each screw loosely to ensure all the
parts are correctly aligned before gently tightening them firmly, but not overtight, in the order
in which you placed them.
The screwdriver can be magnetized by stroking it with a magnet (fridge magnet, etc.) enabling
it to hold the screws and make assembly easier.
If a screw is tight going into a metal part, do not force it as you may shear the head off. Remove
it and put a tiny smear of Vaseline, soap or light oil on the thread. That will lubricate it and make
it easier to drive home.
During the course of this build, you will receive many pieces that you will assemble immediately
– following the instructions in the corresponding stage – and other pieces that you should store
safely to one side, for use in future assembly stages.
Left and Right! When building your Lamborghini, the left or right hand side refers to each side
as you are sitting in the car.
WARNING: Some parts are assembled using magnets. These magnets can cause serious injury
if they are swallowed. Keep away from children. If you suspect a magnet has been swallowed,
seek medical help straight away.
Advice from the experts
!

AGORAMODELS LAMBORGHINI MIURA
3
XXX
Name
Boot compartment
Boot profile
Left rear light lens
Right rear light lens
Reverse light support
Reverse light glass
Adhesive cover
Type B screws x3
STAGE 92 PARTS LIST
In this stage, you’ll assemble the
rear number plate and fit it, along
with the grille and number plate
lights, to the rear body.
The parts supplied will be used in
the next stage and can be kept
aside for now.
Boot profile
Stage 92: Fitting the Rear Number Plate and Grille
Left rear light lens Right rear light lens Reverse light
glass
Boot compartment
Reverse light
support
Adhesive cover
Type B x3

AGORAMODELS LAMBORGHINI MIURA
4
1
3
2
4
Take the number plate lights and the number plate glass (supplied
with Stage 90). The glass has two pins (inset, arrows) which press into
the small holes of the lights (circled). Check the holes for any excess
paint and remove if necessary. Note that the lights have black pins
(arrows) for mounting onto the rear body.
Retrieve the rear body assembly, along with 2x Type B screws (supplied
with Stage 90). The back of the body has two sets of small (circled) and
large (arrows) holes for fitting the lights.
Press the pins of the glass into the holes of the lights. Test fit the
glass in as one side is flatter than the other – the flat side should press
against the silver area of the housing (arrows).
Press the lights into the small and large holes of the rear body so that
the number plate glass is facing each other as shown (arrows).
Stage 92: Fitting the Rear Number Plate and Grille

AGORAMODELS LAMBORGHINI MIURA
5
5 6
With the lights in place, secure them using 2x Type B screws from
inside the body.
Next take the boot lock (supplied with Stage 90, inset). This has a
shaped end for fitting into the hole (arrow) in the rear body located
between the number plate lights.
Stage 92: Fitting the Rear Number Plate and Grille
7 8
Press the boot lock into the shaped hole as shown. You’ll now assemble the number plate. Take the frame, trim and plate
(supplied with Stage 91) and place them on your work surface as
shown. Note the orientation of the frame (arrows).
TYPE B

AGORAMODELS LAMBORGHINI MIURA
6
9 10
Fit the plate by pressing its pins into the inner holes of the frame as
shown in the top image, then press the frame trim into the outer
holes (top image, circled) to secure the parts together as shown in the
bottom image.
Set the number plate aside for now. Take the rear grille (supplied with
Stage 91) along with the rear body assembly.
Stage 92: Fitting the Rear Number Plate and Grille
11
Carefully turn the rear body upside down and turn it around so the inside faces you. Remember to use a
protective surface whenever working with the body so as not to damage the paint. Insert the rear grille into
the body so that the four fixing points (arrows) are aligned as shown.

AGORAMODELS LAMBORGHINI MIURA
7
13 14
Once the rear grille has been fixed, push the raised screw holes of the
number plate into the two remaining holes in the rear body, between
the number plate lights.
Turn the body around and secure the number plate using 2x Type B
screws (supplied with Stage 91).
Stage 92: Fitting the Rear Number Plate and Grille
12
Using 4x Type D screws (supplied with Stage 91) secure the rear grille by driving the screws into the fixing
points highlighted in the previous step.
TYPE D
TYPE B

AGORAMODELS LAMBORGHINI MIURA
8
Stage 92: Fitting the Rear Number Plate and Grille
STAGE COMPLETE

AGORAMODELS LAMBORGHINI MIURA
9
XXX
Name
Boot compartment cover
Speaker
Speaker bracket
Rear body hinge
Type A screws x3
Type B screws x3
STAGE 93 PARTS LIST
You’ll now assemble the boot
compartment, which houses the
speaker for your model, using the
parts provided and those from the
previous stage. You’ll also fit the
rear lights into the rear body.
Speaker
Stage 93: Assembling the Boot Compartment and
Installing the Rear Lights
Speaker bracket
Rear body hinge
Type A x3
Boot compartment cover
Type B x3

AGORAMODELS LAMBORGHINI MIURA
10
1
3
2
4
First you’ll assemble the boot compartment. Retrieve the boot
compartment and adhesive cover (supplied with Stage 92). Note there
is a square recess in the compartment (circled).
Stick the adhesive cover into the recess of the compartment.
Peel the backing paper from the adhesive cover as shown.
Next take the reverse light glass and support (supplied with Stage 92).
The glass has two pins (circled) which fit into the small holes (arrows)
of the support. Fit the glass into the light as shown in the inset image.
Stage 93: Assembling the Boot Compartment and
Installing the Rear Lights

AGORAMODELS LAMBORGHINI MIURA
11
5 6
Press the black pins of the reverse light support into the holes located
by the adhesive cover in the compartment, so that the glass is facing
outwards (arrow).
Turn the compartment over and place it on your work surface.
Align the boot profile (supplied with Stage 92) with it as shown. The
recessed screw holes of the profile fit over the protruding tabs of the
compartment (arrows).
Stage 93: Assembling the Boot Compartment and
Installing the Rear Lights
7 8
Fit the profile onto the compartment. Note the wall of the profile fits
over the outside of the compartment (inset, arrow).
Secure the profile to the compartment using 2x Type B screws
(supplied with Stage 92).
TYPE B TYPE B

AGORAMODELS LAMBORGHINI MIURA
12
9 10
Set the boot compartment aside until it is needed in the next stage.
Take the rear light lenses (supplied with Stage 92), the rear light
housings (assembled in Stage 91) and the rear light LEDs (supplied
with Stage 89 and 90).
Fit the rear light housings into the corresponding left and right holes
in the rear body as shown by the arrows.
Stage 93: Assembling the Boot Compartment and
Installing the Rear Lights
11 12
From inside the rear body, secure the left rear light housing by driving
a Type B screw (supplied with Stage 89) into the raised screw hole.
Secure the right rear light housing in the same way using a second
Type B screw (supplied with Stage 90).
TYPE B
TYPE B

AGORAMODELS LAMBORGHINI MIURA
13
13 14
Take one of the rear light LEDs (supplied with Stage 89 and 90) and
push the bulb end through the hole next to the raised screw hole on
the left-hand side. The rear light LEDs are identical and can be used on
either side.
Push the other rear light LED into the hole on the right-hand side
in the same way. If either of the bulbs are loose, you can use a small
amount of super glue to hold it in place.
Stage 93: Assembling the Boot Compartment and
Installing the Rear Lights
15 16
Turn the rear body back around so that the back is facing you. Press
the tabs of the left rear light lens into the slots of the housing as
shown.
Press the right rear light lens into the housing in the same way.

AGORAMODELS LAMBORGHINI MIURA
14
17
Check that the lenses are fully inserted into the housings so that they are aligned correctly.
Stage 93: Assembling the Boot Compartment and
Installing the Rear Lights
STAGE COMPLETE

AGORAMODELS LAMBORGHINI MIURA
15
XXX
Name
Rear reinforcement structure
Rear window grille
Type B screws x3
STAGE 94 PARTS LIST
Next you’ll fit the speaker into the boot
compartment and then install it in the
rear body. Afterwards, you’ll attach the
characteristic rear window grille of your
Lamborghini Miura.
Rear window grille
Stage 94: Fitting the Window Grille and the Boot
Compartment
Type B x3
Rear reinforcement structure

AGORAMODELS LAMBORGHINI MIURA
16
1
3
2
4
Take the boot compartment assembled in Stage 93 and place it on
your work surface as shown. Note there is a circular recess for fitting
the speaker (circled).
Thread the end of the wire through the hole on the left-hand side of
the compartment as shown (arrow).
Position the speaker (supplied with Stage 93) in the circular recess
inside the boot, so that the wiring leads to your left (arrow), as shown
in the image.
Take the speaker bracket (supplied with Stage 93)and fit its holes over
the raised screw holes either side of the circular recess (arrows). Note
the orientation of the support, with the circuit board of the speaker
still visible (circled).
Stage 94: Fitting the Window Grille and the Boot
Compartment

AGORAMODELS LAMBORGHINI MIURA
17
5 6
Secure the speaker in place by driving 2x Type B screws (supplied with
Stage 93) through the holes of the support.
Now take the boot compartment cover (supplied with Stage 93) and
place it over the speaker, with the raised screw holes facing down.
The short end of the cover should be oriented towards the rear of the
compartment (arrows).
Stage 94: Fitting the Window Grille and the Boot
Compartment
7 8
Turn the compartment over as shown. Take the rear body hinge and
locate the two holes in the compartment for mounting it (circled).
The hinge has two slightly inclined mounting pins (arrows) at the
bottom. Once assembled to the luggage compartment, the hinge
must be inclined towards the reverse light (outside the car).
TYPE B
TYPE B

AGORAMODELS LAMBORGHINI MIURA
18
9 10
Fit the pins of the hinge into the holes of the compartment
(highlighted in steps 7 and 8), so that it is inclined towards the reverse
light (arrow) – see step 10.
Press firmly on the hinge until it sits flush with the raised holes. You
can see that it is inclined towards the reverse light.
Stage 94: Fitting the the Window Grille and the
Boot Compartment
11 12
Now you’ll install the boot compartent into the rear body. Lay the body
upside down as shown on your work surface. Locate the two raised
screw holes next to the LED bulbs (arrows) and the two clamp points
near the boot lid hinges (circled). Align the compartment with the rear
body as shown. Be sure to move the wires of the rear light LEDs aside
before fitting the compartment as shown in the image.
Fit the compartment into the rear body by fitting the tabs on the side
into the clamps and aligning the screw holes. Press firmly to get a
good fit.

AGORAMODELS LAMBORGHINI MIURA
19
13 14
Now take the rear reinforcement structure. Starting with the wide
ends, push the structure against the compartment (arrows), then
lower the screw holes at the sides into the recesses (circled).
Fix the right-hand side of the structure to the right body bulkhead
using a Type B screw.
Stage 94: Fitting the Window Grille and the Boot
Compartment
15 16
In the same way, secure the left-hand side of the structure using a
second Type B screw.
Turn the rear body assembly upright and note the four slots in the
recess of the body (arrows) for fitting the rear window grille. Starting
at the back end, fit the grille in place and press it firmly into the slots.
Note the openings in the grille should face the back end, as shown by
the arrow in the inset image.
TYPE B
TYPE B

AGORAMODELS LAMBORGHINI MIURA
20
Stage 94: Fitting the Window Grille and the Boot
Compartment
STAGE COMPLETE