AMGO 409-P Manual

409-P 409-HP

CONTENTS
Product Features and Specifications ..................................................... 1
Installation Requirement ……………………………………………………………………………… 2
Steps of Installation …........................................................................ 3
Exploded View ................................................................................. 26
Test Run ………....................................................................................30
Operation Instruction .........................................................................31
Maintenance .....................................................................................31
Trouble Shooting ...............................................................................32
Parts List ..........................................................................................33
I. PRODUCT FEATURES AND SPECIFICATIONS

1
4-POST MODEL 409-P 409-HP FEATURES
· Single point manual safety release.
· Four mechanical locking devices, each equipped with both primary
and secondly safety locks.
· Power-side column can be installed at both side, front or rear.
· Non-skid diamond platforms and adjustable safety lock ladders.
· Optional kits: Rolling jack with hand pump, caster kits.
MODEL 409-P 409-HP SPECIFICATIONS
Model
Lifting
Capacity
Lifting
Height
Lifting
Time
Overall
Length
(Inc.
Ramps)
Overall
Width
Width
Between
Columns
Gross
Weight
Motor
409-P
9,000 lbs
73 5/8”
45S
218 3/4”
126 1/4”
112 1/2”
2130lbs
2.0HP
409-HP
9,000 lbs
85 1/2”
53S
230 1/2”
126 1/4”
112 1/2”
2172lbs
2.0HP
II. INSTALLATION REQUIREMENT
Fig. 1

2
A. TOOLS REQUIRED
✓Tape Measure (7.5m)
✓Hammer
✓Level Bar
✓English Spanner (12")
 Wrench set
✓Carpenter’s Chalk
✓Screw Sets
✓Pliers
✓Lock Wrench
 Socket Head Wrench
(12#, 13#, 14#, 15#, 17#, 19#, 24#, 30#) (3#, 5#, 6#, 8#)
B. SPECIFICATIONS OF CONCRETE (See Fig. 3)
Fig. 2

3
Specifications of concrete must be adhered to the specification as following.
Failure to do so may result in lift and/or vehicle falling.
1. Concrete must be thickness 4” minimum and without reinforcing steel bars, and
must be dried completely before the installation.
2. Concrete must be in good condition and must be of test strength 3,000psi
(210kg/cm²) minimum.
3. Floors must be level and no cracks.
C. POWER SUPPLY
The electrical source must be 2.0HP minimum. The source cable size must be
2.5mm² and in good condition of contacting with floor.
III. STEPS OF INSTALLATION
A. Check the parts before assembly
1. Packaged lift and Hydraulic Power Unit (See Fig. 4).
2. Open the outer packing carefully, check the parts according to the shipment list.
(See Fig. 5).
Fig. 4
Fig. 3
Concrete must be of 3,000psi (210kg/cm²)
minimum.

4
3. Take off the drive-in ramps and columns (See Fig.6 ).
4. Loose the screws of the upper package stand, take off the offside platform, take out
the parts inside the powerside platform, then remove the package stand.
5. Move aside the parts and check the parts according to the shipment parts list
(See Fig. 7).
6. Open the carton of parts and check the parts according to the parts box list
Fig. 6
Powerside
Platform
Drive-in
Ramp
Offside
Platform
Cross
Beam
Column
Fig. 5
Parts box
61
Fig. 7
Shipment
Parts List

5
(See Fig. 8).
7. Check the parts of the parts bag according to the parts bag list (See Fig. 9).
B. Use a carpenter’s chalk line to establish installation layout as per Table 1
Fig. 8
Fig. 9

6
Make sure the size is right and base is flat (see Fig. 10).
Note: Reserve space front and behind the installation site.
C. Install cross beams (See Fig.11, Fig.12).
MODEL
A
B
C
409-P
185”
126 1/8”
224”
409-HP
196 7/8”
126 1/8”
233 7/8”
B
A
C
1
Fig. 10
Use a carpenter’s chalk line to establish
installation layout
2

7
D. Install the Safety Ladders.
Fig. 11
Hole towards inside
6
3
The powerside column need to be
installed according to the installed
position of the safety lock release handle.
Fig. 12

8
1. Take off the pulley safety cover and unscrew a nut of the safety ladders, and then
adjust the four lower nuts to be at the same position. Then install the safety
ladder (See Fig. 13).
2. Install Safety Ladders (See Fig. 14).
Fig. 13
Safety Ladder is inserted between
Limited Pins of the cross-beam
Safety Ladder
Limited Pin
Limited Pin
Unscrew a nut of
the safety ladders
Take off the cross
beam plastic cover
Insert the safety ladder
from up to the bottom
between the Limited Pins

9
E. Put the cross beams at the same height and lock on the safety ladder
(See Fig. 15).
F. Install power side platform.
This height for four
threaded rod of safety
ladders should be the
same.
Safety ladder pass through the hole of
the top plate, then tighten the two nuts
Fig. 14
Fig. 15
18
17
The lifting cross beam height
should be fitted for installing the
platform and its parts . 1m
height is recommended.
The safety device on the
cross beam should lock
into the safety ladders at
the same level
Lifting both cross beams
to the same height.

10
1. Install the power side platform on the cross beams by a fork lift or manual, offset
the cross beams to the outside till the pulleys of both platforms can rest into the
cross beams’ slots (See Fig.16), Install the power side platform and screw up the
bolts.
Fig. 16
Offset the cross beam lean
outward when putting the
powerside platform on the
cross beams
Offset the cross beam lean
outward when putting the
powerside platform on the cross
beams
Illustration for front pulley in
powerside platform

11
2. Install tire stop plate with bolts and washer on the platform: Tighten the
platform on cross beam B with bolts, tighten the tire stop plate on cross beam A
with bolts
Note: The bolts for the side with tire stop plate is longer, pay attention when
choosing the bolts (See Fig.17)
Instruction:
1)This lift is designed in both side (cross beam A and cross beam B) car in direction,
user can install the lift according to the location. Below is the installation for the side
of cross beam B car in direction. If choosing the side of cross beam A car in
direction, then install the tire stop plate to the other side.
2)Powerside column can be installed at any position on customers’ requirement, but
the power unit must be installed near the side with the safety lock release handle.
Fig. 17
car in direction
5
Cross beam B
Cross beam A
Interchange the
installed position
according to demand
24
26
25
Tighten the platform
with bolts M16*30
27
28
Tighten the bolts
M16*35 with
washer

12
G. Install offside platform and plastic block, then install the bolts for the platform
strengthen plate, check the plumbness of columns with level and adjusting with the
shims (See Fig. 18).
Fig. 18
Level bar
Install the bolts
for the platform
strengthen plate
33
9
10
32
Note: DO NOT completely
tighten the limit slide blocks.
Loosen 1/4 lap after tightening.
4
29
30
31
Position the slide blocks along
the bent edges of the
columns. Connect the slide
blocks to the cross beam with
bolts.
34

13
H. Illustration for cable installation
1. Pass through the cables from the platform to the columns according to the number
of the cables (See Fig. 19).
NO.
Cable
①
②
③
④
Length for 409-P
(inc. connecting fitting)
124”
363 1/4”
187”
301 3/8”
Length for 409-HP
(inc. connecting fitting)
132 3/4”
383 1/4”
194 3/4”
321 1/4”
Cable installation diagram
A
C
B
35
36
37
38
Install the cylinder
connecting plate as shown
and pay attention to the
direction of unfilled corner
on the plate.
D
Fig. 19
A
B
C
D

14
2. The cable goes through the cross beam to top plate of columns and be screwed with
cable nuts (See Fig. 20).
Fig. 20
Cable goes between
the big pulley and
tension pulley
Cable pass through top
plate and be screwed
with cable nuts.
17

15
3. Illustration for platform cables (See Fig. 21).
Fig. 21
Cable ○ 4
Cable
○
2
Cable
○
2
Cable
○
1
Cable ○ 4
Cable ○ 3
Cable
○
1
Cable
○
2
Cable ○ 4
Cable ○ 2
Cable ○ 3
Cable ○ 4
39
Hex Bolt M10*120
Cable ○ 4
Cable ○ 2
Limit block

16
I. Install connecting bar for safety device and release handle (See Fig. 22).
View B
Cross beam B
Cross beam A
View A
22
44
Connecting bar
Pass through the connecting
bar from the safety lock
rotated device assy. of cross
beam A/B
Safety lock rotated
Device assy.
Connecting bar
43
43A
45A
45
Safety lock rotated
Device assy.
Fig. 22
According to the above diagram, Install
lock release handle to the connecting
bar with M8*35 bolts and washers on
cross beam A.
According to the above diagram, fix
safety lock connecting bar and safety
lock connecting assy. by M8*35 bolts
and washers on cross beam B.

17
J. Install power unit
Note: Power unit must be installed near the safety release handle
1. Install Power unit on the cross beam A, the installation of connection tube as Fig.23
Car in
direction
Cross beam A
Fig. 23
Cross beam B
201
10
46
9
47
40
41
40
Fixing plate
GUDI
42
Install M8*25 Socket bolt with washer to these two holes.

18
2. Install Power unit on the cross beam B (See Fig.24).
Car in
direction
Fig. 24
Cross beam B
40
41
40
Fixing plate
GUDI
42
Install M8*25 Socket bolt with washer to these two holes.