AMGO HS-10 Manual

TWO POST LIFT
Model: HS-10 HS-10H

CONTENTS
Product Features and Specifications ...................................................1
Installation Requirement ..................................................................4
Steps of Installation ........................................................................9
Exploded View ...............................................................................29
Test Run .......................................................................................32
Operation Instruction .....................................................................33
Maintenance .................................................................................34
Trouble Shooting ...........................................................................35
Parts List ......................................................................................36
Safe Tips......................................................................................39

1
I. PRODUCT FEATURES AND SPECIFICATIONS
CLEAR-FLOOR DIRECT-DRIVED MODEL FEATURES
Model HS-10 HS-10H (See Fig. 1)
· Direct-drived design, minimize the lift wear parts and breakdown ratio
· Dual hydraulic cylinders, high standards, utilizing NOK oil seal in cylinder
· Self- lubricating UHMW Polyethylene sliders and bronze bush
· Single-point safety release with dual safety design
. Clear-floor design, provide unobstructed floor use
. Overhead safety shut-off device prevents vehicle damage
. Standard adjustable heights accommodates varying ceiling heights
· Super-asymmetric arms design can fit extremely wide vehicles.
MODEL HS-10 HS-10H SPECIFICATIONS
Model Style Lifting
Capacity
Lifting
Time
Lifting
Height Overall Height Overall Width
Width
Between
columns
Minimum
Pad Height Motor
HS-10
Clear-floor
Direct-drived
5.0 T
10,000 lbs 55S 70-1/2” -
79-1/2” 143-1/8” /147” 137-1/2”
110-1/4” 3-1/2”~12-1/2”
2.0HP
HS-10H
Clear-floor
Direct-drived
5.0 T
10,000 lbs 55S 71-1/2”～
80-1/2” 150”/167-1/8”/171” 137-1/2”
110-1/4” 4-1/2”~13-1/2”
2.0HP
Fig. 1

2
Arm Swings View for Model HS-10 and HS-10H
Fig. 2
Attention: front arm array when car in
Fig. 3

3
Supporting point of lifting arm spread after car in
Fig. 4

4
II. INSTALLATION REQUIREMENT
A. TOOLS REQUIRED
Rotary Hammer Drill (3/4”)
Hammer
Level Bar
English Spanner (12")
Ratchet Spanner With Socket (28#)
Wrench set
Carpenter’s Chalk
Screw Sets
Tape Measure (295”)
Pliers
Socket Head Wrench (3#, 5#, 8#)
Lock Wrench
(10#, 13#, 14#, 15#, 17#, 19#, 24# ,27#, 30#,)
Fig. 5

5
B. SPECIFICATIONS OF CONCRETE (See Fig. 6)
Specifications of concrete must be adhered to the specification as following.
Failure to do so may result in lift and/or vehicle falling.
1. Concrete must be thickness 4” minimum and without reinforcing steel bars, and
must be completely dry before lift installation.
2. Concrete must be in good condition and must be of test strength 3,000psi
minimum.
3. Floors must be level with no cracks or holes.
C. POWER SUPPLY
The electrical source must be 2.0HP minimum. The source cable size must be
2.5mm2and in good condition of contacting with floor.
III.INSTALLATION STEPS
A. Location of installation
Check and ensure the installation location (concrete, layout, space size etc.) is
suitable for lift installation.
B. Use a carpenter’s chalk line to establish installation layout of base-plate (See Fig. 7).
Fig. 6
Chalk Line
137- 1/2”
Fig. 7
29
Concrete intensity must be 3,000psi
HS-10/HS-10H installation diagram

6
C. Check the parts before assembly.
1. Packaged lift and hydraulic power unit (See Fig. 8).
2. Move the lift aside with a fork lift or hoist, and open the outer packing carefully and
remove aside the top connecting assy. and parts box
(See Fig. 9).
3. Lift the upper column with a fork lift or hoist, loose the bolts of the upper package
stand, take off the upper extension column, then take out the parts in the inner
column (See Fig. 10).
Shipment Parts list
Top Connecting Assy.
Parts box
Serial No.
Fig. 8
Fig. 9
Fig. 10

7
4. Lift the lower column with a fork lift or hoist, take down the package stand, than take
off the lower extension column, take out the parts in the inner column (See Fig. 11).
5. Move aside the parts and check the parts according to the shipment parts list. Open
the carton of parts and check the parts according to parts box list
(See Fig. 12, Fig.13).
6. Check the parts of the parts bag 1 according to parts bag list (See Fig. 14).
Fig. 11
Fig. 12
Fig. 14
87
Fig. 13
Part box(87)
Raise up the lift by forklift truck
Remove package
Fig. 14

8
7. Check the parts of the parts bag 2 according to parts bag list (See Fig. 15).
8. Check the parts of the parts bag 3 according to parts bag list (See Fig. 16).
D. Install parts of extension columns (See Fig. 17).
Fig. 15
Fig. 17
Fig. 16
Fig. 15

9
E. Install hydraulic cylinder
Warp the tape to both side of straight fitting and connecting it with 90° fitting, then
install the cylinder into the carriages (See Fig. 18).
Fig. 18
Powerside column
Offside column
Put the fitting
down and across
the hole inside
the column
59
58
61
81○
390○
4
84○
2
82
90
82○
1
Connect the fitting
in order
Put the cylinder into
column which wrap
with tape and
assemble fitting
With M12 screw, lock washer
and washer to fix the cylinder

10
F. Install columns
Lay down two columns on the installation site parallelly, position the power side
column according to the actual installation site. Usually, it is suggested to install
power side column on the front-right side from which vehicles are driven to the lift.
This lift is designed with 2-section columns. Adjustable height according to the
ceiling height and connecting the inner and extension columns.
For model HS-10
1. When the ceiling height is over 147-5/8”, connecting the extension columns with the
lower holes (See Fig. 19).
Fig. 19 High Setting (HS-10)

11
2. When the ceiling height is lower than 147-5/8”, connecting the extension columns
with the upper holes (See Fig.20).
Fig. 20 Low Setting (HS-10)

12
For model HS-10H
1. When the ceiling height is over 171-1/4”, connecting the extension columns with the
lower holes (See Fig. 21).
Fig. 21 High Setting(HS-10H)

13
2. When the ceiling height is over 167-1/4” but lower than 171-1/4”, connecting the
extension columns with the middle holes (See Fig.22).
Fig. 22 Median Setting(HS-10H)

14
3. When the ceiling height is lower than 167-1/4”, connecting the extension columns
with the upper holes. (See Fig.23).
Fig. 23 Low Setting(HS-10H)

15
G. Position columns
Position the columns on the installation layout of base plate. Check the columns
vertical with level bar, and adjusting with the shims if the columns are not vertical.
Do not tighten the anchor bolts (See Fig.24).
Note: Minimum embedment of Anchors is 3-1/2”.
30/90
Width between
columns:110-1/4”
Adjusting with
the shims
Overall width
：
137-1/2”
Fig. 24
Drilling
Cleaning
Bolting
3-1/2”

16
H. Install overhead top beam
1. With help of the hook of top beam, put one side of top beam on top of the extension
column and connecting the top beam to extension column by bolts, tighten the bolts.
Then assemble the connecting bracket (See Fig. 25).
Fig. 25
Hook on to the
extension columns
Tighten the bolts

17
2. Assemble overhead top beam, tighten the columns anchor bolts (See Fig. 26).
Fig. 26
Tighten
Tighten the anchor bolts with
ratchet spanner with socket
Torque of tighten the anchor
bolts is 150N.m.

18
I. Installing the limit switch control bar and limit switch (See Fig. 27).
Loosen screw of drive
rod for adjustment,
tighten the screw
after adjustment
Limit switch
connected
with cable
54
Connect the brown wire
to the terminal 12# on
limit switch and terminal
4# on control button.
Connect the blue wire to
terminal 11# on limit switch
and terminal A1 on AC
contactor of power unit
Connect the yellow and
green wire to the earth
wire terminal on limit
switch and the earth wire
terminal of power unit.
NC: Normal contact
Fig. 27