Analog Devices EZ-KIT Lite ADSP-21364 User manual

ADSP-21364 EZ-KIT Lite®
Evaluation System Manual
Revision 2.0, January 2005
Part Number
82-000840-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106 a

Copyright Information
© 2005 Analog Devices, Inc., ALL RIGHTS RESERVED. This docu-
ment may not be reproduced in any form without prior, express written
consent from Analog Devices, Inc.
Printed in the USA.
Limited Warranty
The EZ-KIT Lite evaluation system is warranted against defects in materi-
als and workmanship for a period of one year from the date of purchase
from Analog Devices or from an authorized dealer.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by impli-
cation or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, VisualDSP++, the VisualDSP++ logo, SHARC,
CROSSCORE, the CROSSCORE logo, and EZ-KIT Lite are registered
trademarks of Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.

Regulatory Compliance
The ADSP-21364 EZ-KIT Lite evaluation system has been certified to
comply with the essential requirements of the European EMC directive
89/336/EEC (inclusive 93/68/EEC) and, therefore, carries the “CE”
mark.
The ADSP-21364 EZ-KIT Lite evaluation system had been appended to
Analog Devices Development Tools Technical Construction File refer-
enced “DSPTOOLS1” dated December 21, 1997 and was awarded CE
Certification by an appointed European Competent Body and is on file.
The EZ-KIT Lite evaluation system contains ESD
(electrostatic discharge) sensitive devices. Electro-
static charges readily accumulate on the human
body and equipment and can discharge without
detection. Permanent damage may occur on devices
subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance
degradation or loss of functionality. Store unused
EZ-KIT Lite boards in the protective shipping
package.

CONTENTS
iv ADSP-21364 EZ-KIT Lite Evaluation System Manual

ADSP-21364 EZ-KIT Lite Evaluation System Manual v
CONTENTS
PREFACE
Purpose of This Manual ................................................................. xii
Intended Audience ........................................................................ xiii
Manual Contents .......................................................................... xiii
What’s New in This Manual ........................................................... xiv
Technical or Customer Support ...................................................... xiv
Supported Processors ....................................................................... xv
Product Information ....................................................................... xv
MyAnalog.com .......................................................................... xv
Processor Product Information .................................................. xvi
Related Documents .................................................................. xvi
Online Technical Documentation ........................................... xviii
Accessing Documentation From VisualDSP++ .................... xviii
Accessing Documentation From Windows ............................ xix
Accessing Documentation From Web ................................... xix
Printed Manuals ....................................................................... xix
VisualDSP++ Documentation Set .......................................... xx
Hardware Tools Manuals ....................................................... xx
Processor Manuals ................................................................. xx

CONTENTS
vi ADSP-21364 EZ-KIT Lite Evaluation System Manual
Data Sheets .......................................................................... xx
Notation Conventions ................................................................... xxi
USING EZ-KIT LITE
Package Contents ......................................................................... 1-2
Default Configuration .................................................................. 1-3
Installation and Session Startup ..................................................... 1-5
Evaluation License Restrictions ..................................................... 1-6
External Memory .......................................................................... 1-6
Analog Audio ............................................................................... 1-7
LEDs and Push Buttons ................................................................ 1-9
Example Programs ...................................................................... 1-10
Background Telemetry Channel .................................................. 1-11
VisualDSP++ Interface ................................................................ 1-11
Boot Load ............................................................................. 1-11
Target Options ...................................................................... 1-12
While Target is Halted and On Emulator Exit Options ...... 1-12
Other Options .................................................................. 1-12
Core Hang Conditions .......................................................... 1-13
Hardware Breakpoints ........................................................... 1-15
Data Hardware Breakpoints .............................................. 1-16
Instruction Hardware Breakpoints ..................................... 1-17
Other Breakpoints ............................................................ 1-18
Common Hardware Breakpoint Attributes ........................ 1-19
Global Hardware Breakpoint Options ............................... 1-19

ADSP-21364 EZ-KIT Lite Evaluation System Manual vii
CONTENTS
Miscellaneous ................................................................... 1-19
EZ-KIT LITE HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
Parallel Port ............................................................................. 2-3
DAI Interface .......................................................................... 2-5
SPI Interface ........................................................................... 2-6
FLAG Pins .............................................................................. 2-6
Expansion Interface ................................................................. 2-7
JTAG Emulation Port .............................................................. 2-8
Switch Settings .............................................................................. 2-8
Electret Microphone Select Switch (SW6) ................................ 2-8
Codec Setup Switch (SW7) ...................................................... 2-8
Push Button Enable Switch (SW9) ......................................... 2-10
Boot Mode and Clock Ratio Select Switch (SW10) ................. 2-11
Loop-Back Test Switch (SW11) ............................................. 2-12
LEDs and Push Buttons .............................................................. 2-12
General Purpose LEDs (LED8–1) .......................................... 2-12
Reset LEDs (LED9 and LED12) ............................................ 2-12
Power LED (LED10) ............................................................. 2-13
USB Monitor LED (LED13) ................................................. 2-13
Push Buttons (SW4–1) .......................................................... 2-14
Board Reset Push Button (SW5) ............................................ 2-14
Connectors ................................................................................. 2-15
Expansion Interface (J3–J1) ................................................... 2-16

CONTENTS
viii ADSP-21364 EZ-KIT Lite Evaluation System Manual
Audio In RCA Connector (J4) ............................................... 2-17
Audio Out RCA Connector (J5) ............................................ 2-17
Headphone Out Jack (J6) ...................................................... 2-17
Power Jack (J7) ..................................................................... 2-17
SPDIF Coax Connectors (J8 and J9) ..................................... 2-18
SPI Header (P2) .................................................................... 2-18
DAI Header (P3) .................................................................. 2-19
USB Connector (P4) ............................................................. 2-19
JTAG Header (P5) ................................................................ 2-19
BILL OF MATERIALS
INDEX

ADSP-21364 EZ-KIT Lite Evaluation System Manual ix
PREFACE
Thank you for purchasing the ADSP-21364 EZ-KIT Lite®, Analog
Devices, Inc. evaluation system for SHARC®processors.
The SHARC processors are based on a 32-bit super Harvard architecture
that includes a unique memory architecture comprised of two large
on-chip, dual-ported SRAM blocks coupled with a sophisticated IO pro-
cessor, which gives a SHARC processor the bandwidth for sustained
high-speed computations. SHARC processors represents today’s de facto
standard for floating-point processor targeted for premium audio
applications.
The evaluation system is designed to be used in conjunction with the
VisualDSP++®development environment to test the capabilities of the
ADSP-21364 SHARC processors. The VisualDSP++ development envi-
ronment gives you the ability to perform advanced application code
development and debug, such as:
• Create, compile, assemble, and link application programs written
in C++, C, and ADSP-21364 assembly
• Load, run, step, halt, and set breakpoints in application program
• Read and write data and program memory
• Read and write core and peripheral registers
• Plot memory

x ADSP-21364 EZ-KIT Lite Evaluation System Manual
Access to the ADSP-21364 processor from a personal computer (PC) is
achieved through a USB port or an optional JTAG emulator. The USB
interface gives unrestricted access to the ADSP-21364 processor and the
evaluation board peripherals. Analog Devices JTAG emulators offer faster
communication between the host PC and target hardware. Analog Devices
carries a wide range of in-circuit emulation products. To learn more about
Analog Devices emulators and processor development tools, go to
http://www.analog.com/dsp/tools/.
LThe ADSP-21364 EZ-KIT Lite installation is part of the Visu-
alDSP++ installation. The EZ-KIT Lite is a licensed product that
offers an unrestricted evaluation license for the first 90 days. Once
the initial unrestricted 90-day evaluation license expires:
• VisualDSP++ allows a connection to the ADSP-21364
EZ-KIT Lite via the USB Debug Agent interface only. Con-
nections to simulators and emulation products are no longer
allowed.
• The linker restricts a users program to 10922 words of
internal memory for code space with no restrictions for data
space.
ADSP-21364 EZ-KIT Lite provides example programs to demonstrate the
capabilities of the evaluation board.
The board features:
• Analog Devices ADSP-21364 processor
D136-pin BGA package
D300 MHz Core Clock Speed

ADSP-21364 EZ-KIT Lite Evaluation System Manual xi
Preface
• Synchronous Random Access Memory (SRAM)
D512 Kbit x 8-bit
• Flash Memory
D1M x 8-bit
• Serial Peripheral Interconnect (SPI) Flash Memory
D512 Kbit
• Analog Audio Interface
DAD1835A codec
D4x2 RCA phono jack for 4 channels of stereo output
D2x1 RCA phono jack for 1 channel of stereo input
DHeadphone jack for 1 channel stereo output
• Digital Audio Interface
DRCA phono jack output
DRCA phono jack input
•LEDs
D12 LEDs: 1 power (green), 1 board reset (red), 1 USB reset
(red), 1 USB monitor (amber), and 8 general purpose
(amber)
• Push Buttons
D5 push buttons: 1 reset, 2 connected to DAI,
2 connected to the FLAG pins of the processor

Purpose of This Manual
xii ADSP-21364 EZ-KIT Lite Evaluation System Manual
• Expansion Interface (Type A)
DParallel Port, FLAGs, DAI, SPI
• Other Features
DJTAG ICE 14-pin header
D0-ohm resistors for processor current measurement
DSPI header
DDAI header
The EZ-KIT Lite board has a total of 1 MB of parallel flash memory and
512 Kbit of SPI flash memory. The flash memories can store user-specific
boot code, allowing the board to run as a stand-alone unit. For more
information, see “External Memory” on page 1-6 and “Boot Mode and
Clock Ratio Select Switch (SW10)” on page 2-11. The board also has
512 KB of SRAM, which can be used at runtime.
The DAI of the processor connects to the AD1835A audio codec and two
connectors, which allow SPDIF input and output. The interface facilitates
development of digital and analog audio signal-processing applications.
See “Analog Audio” on page 1-7 and “SPDIF Coax Connectors (J8 and
J9)” on page 2-18 for more information.
Additionally, the EZ-KIT Lite board provides access to all of the proces-
sor’s peripheral ports. Access is provided in the form of a three-connector
expansion interface. See “Expansion Interface” on page 2-7 for details.
Purpose of This Manual
The ADSP-21364 EZ-KIT Lite Evaluation System Manual provides
instructions for installing the product hardware (board) and describes the
operation and configuration of the board components. The product soft-
ware component is detailed in the VisualDSP++ Installation Quick

ADSP-21364 EZ-KIT Lite Evaluation System Manual xiii
Preface
Reference Card. The manual provides guidelines for running your own
code on the ADSP-21364 EZ-KIT Lite. Finally, a schematic and a bill of
materials are provided as a reference for future designs.
Intended Audience
The primary audience for this manual is a programmer who is familiar
with Analog Devices processors. This manual assumes that the audience
has a working knowledge of the appropriate processor architecture and
instruction set. Programmers who are unfamiliar with Analog Devices
processors can use this manual but should supplement it with other texts
(such as the ADSP-2136x SHARC Processor Programming Reference and
ADSP-2136x SHARC Processor Hardware Reference) that describe your tar-
get architecture.
Programmers who are unfamiliar with VisualDSP++ should refer to the
VisualDSP++ online Help and the VisualDSP++ user’s or getting started
guides. For the locations of these documents, see “Related Documents”.
Manual Contents
The manual consists of:
• Chapter 1, “Using EZ-KIT Lite” on page 1-1
Provides information on the EZ-KIT Lite from a programmer’s
perspective and provides an easy-to-access memory map.
• Chapter 2, “EZ-KIT Lite Hardware Reference” on page 2-1
Provides information on the hardware aspects of the evaluation
system.

What’s New in This Manual
xiv ADSP-21364 EZ-KIT Lite Evaluation System Manual
• Appendix A, “Bill Of Materials” on page A-1
Provides a list of components used to manufacture the EZ-KIT
Lite board.
• Appendix B, “Schematics” on page B-1
Provides the resources to allow modifications to the EZ-KIT Lite
or to use as a reference design.
LThis appendix is not part of the online Help. The online Help
viewers should go to the PDF version of the ADSP-21364 EZ-KIT
Lite Evaluation System Manual located in the Docs\EZ-KIT Lite
Manuals folder on the installation CD to see the schematics. Alter-
natively, the schematics can be found on the Analog Devices Web
site, www.analog.com/processors.
What’s New in This Manual
This revision of the ADSP-21364 EZ-KIT Lite Evaluation System Manual
provides an updated listing of related documents and updated licensing
information.
Technical or Customer Support
You can reach DSP Tools Support in the following ways.
• Visit the Embedded Processing and processor products Web site at
http://www.analog.com/processors/technicalSupport
• E-mail tools questions to
[email protected]
• E-mail processor questions to
[email protected]
• Phone questions to 1-800-ANALOGD

ADSP-21364 EZ-KIT Lite Evaluation System Manual xv
Preface
• Contact your Analog Devices, Inc. local sales office or authorized
distributor
• Send questions by mail to:
Analog Devices, Inc.
One Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
USA
Supported Processors
The ADSP-21364 EZ-KIT Lite evaluation system supports the Analog
Devices ADSP-21364 SHARC processors.
Product Information
You can obtain product information from the Analog Devices Web site,
from the product CD-ROM, or from the printed publications (manuals).
Analog Devices is online at www.analog.com. Our Web site provides infor-
mation about a broad range of products—analog integrated circuits,
amplifiers, converters, and digital signal processors.
MyAnalog.com
MyAnalog.com is a free feature of the Analog Devices Web site that allows
customization of a Web page to display only the latest information on
products you are interested in. You can also choose to receive weekly
e-mail notifications containing updates to the Web pages that meet your
interests. MyAnalog.com provides access to books, application notes, data
sheets, code examples, and more.

Product Information
xvi ADSP-21364 EZ-KIT Lite Evaluation System Manual
Registration:
Visit www.myanalog.com to sign up. Click Register to use MyAnalog.com.
Registration takes about five minutes and serves as means for you to select
the information you want to receive.
If you are already a registered user, just log on. Your user name is your
e-mail address.
Processor Product Information
For information on embedded processors and processors, visit our Web
site at www.analog.com/processors, which provides access to technical
publications, data sheets, application notes, product overviews, and prod-
uct announcements.
You may also obtain additional information about Analog Devices and its
products in any of the following ways.
• E-mail questions or requests for information to
[email protected]
• Fax questions or requests for information to
1-781-461-3010 (North America)
[phone] (Europe)
• Access the FTP Web site at
ftp ftp.analog.com or ftp 137.71.23.21
ftp://ftp.analog.com
Related Documents
For information on product related development software and hardware,
see these publications:

ADSP-21364 EZ-KIT Lite Evaluation System Manual xvii
Preface
LIf you plan to use the EZ-KIT Lite board in conjunction with a
JTAG emulator, also refer to the documentation that accompanies
the emulator.
All documentation is available online. Most documentation is available in
printed form.
Visit the Technical Library Web site to access all processor and tools man-
uals and data sheets:
http://www.analog.com/processors/resources/technicalLibrary
Table 1. Related Processor Publications
Title Description
ADSP-21364 SHARC Microprocessor Datasheet General functional description, pinout, and
timing
ADSP-2136x SHARC Processor Hardware Refer-
ence
Description of internal processor architecture,
registers, and all peripheral functions
ADSP-2136x SHARC Processor Programming
Reference
Description of all allowed processor assembly
instructions
Table 2. Related VisualDSP++ Publications
VisualDSP++ User’s Guide Detailed description of VisualDSP++ features
and usage
VisualDSP++ Assembler and Preprocessor Man-
ual
Description of the assembler function and
commands
VisualDSP++ C/C++ Complier and Library
Manual for SHARC Processors
Description of the complier function and com-
mands for SHARC processors
VisualDSP++ Linker and Utilities Manual Description of the linker function and com-
mands
VisualDSP++ Loader Manual Description of the loader function and com-
mands

Product Information
xviii ADSP-21364 EZ-KIT Lite Evaluation System Manual
Online Technical Documentation
Online documentation comprises the VisualDSP++ Help system, software
tools manuals, hardware tools manuals, processor manuals, the Dinkum
Abridged C++ library, and Flexible License Manager (FlexLM) network
license manager software documentation. You can easily search across the
entire VisualDSP++ documentation set for any topic of interest. For easy
printing, supplementary .PDF files of most manuals are provided in the
Docs folder on the VisualDSP++ installation CD.
Each documentation file type is described as follows.
If documentation is not installed on your system as part of the software
installation, you can add it from the VisualDSP++ CD at any time by run-
ning the Tools installation. Access the online documentation from the
VisualDSP++ environment, Windows®Explorer, or the Analog Devices
Web site.
Accessing Documentation From VisualDSP++
To view VisualDSP++ Help, click on the Help menu item or go to the
Windows task bar and navigate to the VisualDSP++ documentation via
the Start menu.
File Description
.CHM Help system files and manuals in Help format
.HTM or
.HTML
Dinkum Abridged C++ library and FlexLM network license manager software doc-
umentation. Viewing and printing the .HTML files requires a browser, such as
Internet Explorer 4.0 (or higher).
.PDF VisualDSP++ and processor manuals in Portable Documentation Format (PDF).
Viewing and printing the .PDF files requires a PDF reader, such as Adobe Acrobat
Reader (4.0 or higher).

ADSP-21364 EZ-KIT Lite Evaluation System Manual xix
Preface
To view ADSP-21364 EZ-KIT Lite Help,which is part of the Visu-
alDSP++ Help system, use the Contents or Search tab of the Help
window.
Accessing Documentation From Windows
In addition to any shortcuts you may have constructed, there are many
ways to open VisualDSP++ online Help or the supplementary documenta-
tion from Windows.
Help system files (.CHM) are located in the Help folder, and .PDF files are
located in the Docs folder of your VisualDSP++ installation CD-ROM.
The Docs folder also contains the Dinkum Abridged C++ library and the
FlexLM network license manager software documentation.
Your software installation kit includes online Help as part of the Win-
dows® interface. These help files provide information about
VisualDSP++ and the ADSP-21364 EZ-KIT Lite evaluation system.
Accessing Documentation From Web
Download manuals at the following Web site:
http://www.analog.com/processors/resources/technicalLibrary/man-
uals.
Select a processor family and book title. Download archive (.ZIP) files, one
for each manual. Use any archive management software, such as WinZip,
to decompress downloaded files.
Printed Manuals
For general questions regarding literature ordering, call the Literature
Center at 1-800-ANALOGD (1-800-262-5643) and follow the prompts.

Product Information
xx ADSP-21364 EZ-KIT Lite Evaluation System Manual
VisualDSP++ Documentation Set
To purchase VisualDSP++ manuals, call 1-603-883-2430. The manuals
may be purchased only as a kit.
If you do not have an account with Analog Devices, you are referred to
Analog Devices distributors. For information on our distributors, log onto
http://www.analog.com/salesdir/continent.asp.
Hardware Tools Manuals
To purchase EZ-KIT Lite and In-Circuit Emulator (ICE) manuals, call
1-603-883-2430. The manuals may be ordered by title or by product
number located on the back cover of each manual.
Processor Manuals
Hardware reference and instruction set reference manuals may be ordered
through the Literature Center at 1-800-ANALOGD (1-800-262-5643),
or downloaded from the Analog Devices Web site. Manuals may be
ordered by title or by product number located on the back cover of each
manual.
Data Sheets
All data sheets (preliminary and production) may be downloaded from the
Analog Devices Web site. Only production (final) data sheets (Rev. 0, A,
B, C, and so on) can be obtained from the Literature Center at
1-800-ANALOGD (1-800-262-5643); they also can be downloaded from
the Web site.
To have a data sheet faxed to you, call the Analog Devices Faxback System
at 1-800-446-6212. Follow the prompts and a list of data sheet code
numbers will be faxed to you. If the data sheet you want is not listed,
check for it on the Web site.