Anova L1369A User manual

anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED:
• 11/16" Open-end or Box-end Wrench
• Ratchet with 11/16" Socket
• 7/16" Open-end Wrench
• Flat Head Screw Driver
• Level
Assembly Instructions
Streetside
L1369A - Streetside 6' Contour Bench with Divided Seating
COMPONENT PARTS:
ASSEMBLY HARDWARE: All hardware is stainless steel.
(4) 7/16"-14
Hex Nut
(4) 7/16" Lock Washer (4) 7/16" Flat Washer (8) 1/4"-20
Acorn Nut
(8) 1/4" Flat
Washer
(8) 1/4"-20 X 3/4"
Slotted Bolt
(1) Contour Bench Seat (1) Right Side
Bench End
(1) Le Side
Bench End
ASSEMBLY:
Inspect the shipping container contents for damage and to
determine that all components and hardware are present.
1.
The assembly is a two-person operation.
2. Lay all parts on a so work surface or on the shipping
packaging to prevent damage to nish.
3. Align the mounting studs in one of the bench ends with the
holes in the appropriate end of the bench seat.
4. Insert the mounting studs on the bench end through the
mounting holes in the bench seat. Install a 7/16" at washer,
then a 7/16" lock washer and a 7/16" hex nut on each of the
mounting studs.
Repeat this step for the opposite bench end.
Leave the hardware nger tight so that adjustments can be
made during assembly and to level the bench.
NOTE: Before assembling the nuts to the bolts, it is
recommended that a light oil or petroleum jelly be applied to
the screw threads.
1
(2) Armrests
7/16" Hex Nut
7/16" Hex Nut
7/16" Lock Washer
7/16" Lock Washer
7/16" Flat Washer
7/16" Flat Washer
Mounting Studs
Hole near middle of
bench seat denotes
backrest portion
Hole near bend of bench
seat denotes seat portion

2
7/16" Hex Nut
7/16" Hex Nut
7/16" Lock Washer
7/16" Lock Washer
7/16" Flat Washer
7/16" Flat Washer
5. Align an armrest with the mounting holes on the bench. Insert
a 1/4"-20 slotted bolt with a 1/4" at washer through the back
of the bench. Place another washer on the bolt from the front
of the bench and secure a 1/4"-20 acorn nut onto the bolt.
Repeat this process with the remaining hardware on both
armrests.
Leave the hardware nger tight so adjustments can be made
during assembly.
6. Tighten the bench end hardware using the 11/16" wrench and 11/16" socket, while checking the seat
surface with a level; minor adjustments can be made while tightening the hardware to make the
seat level. Tighten the armrest hardware with a at head screw driver and a 7/16" open-end wrench.
7. Aer two weeks, retighten all hardware.
Front View
Back View
1/4" Flat Washer
1/4" Acorn Nut
1/4"-20 Slotted Bolt
1/4" Flat Washer
Mounting Stud

Copyright 2019 ANOVA® Manufactured in the U.S. 3
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
09/25/2019
VIEW A-A
SCALE 1:14
SECTION B-B
SCALE 1:14
A A
B B
1
1
2
2
3
3
4
4
A A
B B
THIRD ANGLE PROJECTION
TOLERANCES UNLESS NOTED:
X
 1 X.X  .5 X.XX ±.25 X.XXX ±.125
X.XXXX ±.0625 X.XXXXX ±.03125
X.XXXXXX
 .015625 ANGULAR ±1°
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125 .0625 DURING COATING.
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
[e-mail]
anovafurnishings.com
DRAWN
???
SIZE
BL1369A-SPEC-REV-001
DATE 9/25/2019 SCALE
.09375:1 SHEET
DWG NO
TITLE
D. METZ
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
REV
1 OF
???
1
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
1 ???? ????-??? ??/??/13
33.45
19.11
4.00
23.58
25.57
75.25
72.25
1.50
23.31 22.50
75.50
 .50
(4 PLCS)
16.83
73.63
FOOT MOUNT
73.63"
16.83"
Ø.50"
(4 PLCS)
Assembly and Replacement Parts
Armrest
Right Side Bench End
Le Side Bench End
Contour Bench Seat