Argos Linear 247/6216 User manual

MADE IN
BRITAIN
Dimensions
Linear - 5 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 10/06/14
Important - Please read these instructions fully before starting assembly
ALR3058
247/6216
266/8732
278/1671
Width - 79.5cm
Depth - 39cm
Height - 104cm

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 35.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
12
3
5 6
7 8 9
10
11
Base (DF147)
(791 x 368mm)
Top (DF143)
(795 x 390mm)
Drawer Back (W708-124)
(708 x 124mm) x 5
Drawer Base (T719-347)
(719 x 347mm) x 5
Drawer Front (DF145)
(783 x 187mm) x 5
Left Drawer
Side (W350-124LH)
(350 x 124mm) x 5
Right Drawer
Side (W350-124RH)
(350 x 124mm) x 5
Back (X984-785)
(984 x 785mm)
Left Side (DF843)
(963 x 366mm)
Right Side (DF844)
(963 x 366mm)
Cross Rail (DF144)
(759 x 94mm)
4

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
B C
D E F
G H
Small locking
nut (F3) x 10
Nail (F51) x 24
I
A
Wooden dowel (F22) x 10 Metal dowel (F901) x 16
Large locking
nut (F900) x 6 Knock-in Peg (F171GY) x 20
MR Runner (F160) x 5
b
L Runner (F161) x 5
Mc
L Runner (F159) x 5
Ma
R Runner (F162) x 5
Md
350mm long
40mm Screw (F910) x 4
N
13mm Screw (F52) x 30
J
13mm Screw (F79) x 26 13mm Screw (F63) x 30
KL
Wedgefix (F639) x 20
N
Foot
(F233) x 4
O
38mm Screw (F81) x 8
N
P
N
P
Bracket (F327) x 1
P
Handle (F283) x 5
780mm long

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
B
B
C
C
CC
8
Step 2
Prepare the 5 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
6
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
8
9
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
9
6
C
C
8
9
x 5
x 5
x 5
x 5
80%
9
6
B
B
6
8
8
9

Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
10
8 9
6
7
8 9
10
7
7
E
8 9
Fit the handle
Position a handle
onto the top edge of the
drawer front .
Fix the handle to the
back surface of the
drawer front using 5
screws .
P
6
P
J
6
6
E
E
E
E
10
8
9
10
7
8
9
J
J
J
J
J
P
6
x 5
x 5
x 5

Assembly Instructions
6
Step 7
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
L
L
LL
L
L
Fit runners to the
drawers
Fit the runner to the
bottom edge of the left
drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit the runner to the
bottom edge of the right
drawer side using the
same method.
9
M c
8
6
K
M d
K
K
M d
Runners must be
pushed up against
the drawer front
8
6
Step 8
M c
9
K
K
x 5
x 5

1
1
1
Finished
front edge
Assembly Instructions
7
Step 9
M a
I
Finished front edge
I
1st
screw
2nd
screw
I
3rd
screw
b:
c:
M a
Finished front edge
K
Prepare the left side
a: Fit 5 runners to
the left side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runners .
c: Tap 4 wooden
dowels into the left
side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Screw a metal dowel
into the left side .
A
D
1
1
M a
1
I
I
K
M a
I
M a
I
I
I
M a
I
I
I
M a
I
I
I
M a
I
I
I
M a
I
I
Finished
front edge
K
K
K
K
K
Finished
front edge
A
A
A
A
10mm
A
D
D
D
B
B
1

A
A
Assembly Instructions
8
Step 10
Prepare the right side
a: Fit 5 runners to
the right side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runners .
c: Tap 4 wooden
dowels into the right
side .
Insert 2 large locking
nuts into the right
side . .
Screw a metal dowel
into the right side .
M b
2
I
I
K
M b
M b
I
Finished front edge
I1st
screw
2nd
screw
I3rd
screw
a:
b:
c:
A
D
2
2
M b
Finished front edge
K
K
K
K
K
K
I
I
M b
I
I
I
M b
I
I
I
M b
I
I
I
M b
I
I
I
M b
I
D
D
A
A
Finished
front edge
Finished
front edge
Finished
front edge
B
B
2
2
2
2

Finished
front edge
Finished
front edge Finished
front edge
A
Assembly Instructions
9
Step 11
Prepare the cross rail
Tap 2 wooden dowels
into the cross rail .
Insert 2 large locking
nuts into the
cross rail .
Fit the left side to the
cross rail
Push the left side
onto the cross rail .
Use a screwdriver to
tighten the large
locking nut fitted
to the cross rail .
Step 13
D
D
A
A
4
4
D
4
Fit the cross rail to
the right side
Push the cross rail
onto the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the cross
rail .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
4
D
D
Step 12
B
D
4
2
4
4
1
1
4
D
4
Finished
front edge