Argos HOME 617/9296 User manual

Width - 53cm
Depth - 54cm
Height - 89-101cm
Dimensions
Mid back Office Chair
Assembly Instructions - Please keep for future reference
Issue 1 - 11/10/16
617/9296
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800

1
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product, this
could cause damage.
•Assemble the item as close to
its final position (in the same
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Unit weight: 8.9 kgs.
• Maximum safe weight of user:
110kgs.
Care and maintenance
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• Do not stand on the chair.
• Do not use this chair as step
ladder.
•This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Handy Hints
•Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.

2
Please check you have all the parts listed below
1Backrest
(43 x 42 x 9cm)
2Back Frame
46Base
(Ø30 x 6 cm)
5Arm Rest x 2
(31 x 24 x 16cm)
Seat
(47.5 x 42 x 11.5cm)
(29.5 x 10 x 7.5cm)
3Chair Lift Plate
7Plastic Sleeve 8Gaslift
(29/41 x Ø5 cm)
9Castor x 5
Components - Parts If you have damaged or missing components, call the
Customer Helpline: Argos = 0345 640 0800
Back connector
10

3
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A B C
M6 x 35mm Bolt x 6 M6 x 18mm Bolt x 4 M6 x 25mm Bolt x 2
D E
Small Washer x 10 Allen Key x 1

4
Assembly Instructions
Step 1
Step 2
4
3
FRONT
B
5
5
5
4
4
4
A
A
A
A
A
A
A
A
A
Attaching the chair lift
plate
Place the seat upside
down on a raised
protected surface.
Position the chair lift
plate onto the seat
as shown and make sure
that the arrow stamped
on the metal plate is
pointing to the front of
the seat.
Align the holes and fix
using bolts and small
washers . Tighten bolts
using allen key .
43
B
B
D
D
B
B
D
B
D
D
E
D
D
D
D
D
D
D
D
D
Attaching armrests
3
Attach the armrest
to the seat . Then
align the holes and fix
using bolts and small
washer . Tighten bolts
using allen key .
5
4
A
D
E
Note:The two bolts at this
stage is not fully tightened
D
arrow
arrow

Step 3
Step 4
Firstly remove the knob
and washer on the back
frame by turning it
counter-clockwise.
2
2
washer
spring washer
knob
Assembly Instructions
Attaching back frame
5
a: Insert the metal part
of the back connector
into metal rod on the
back frame as
shown.
b: Then attach the back
frame to backrest
as shown and fix using
the plastic part of the
back connector and
bolts . Tighten bolts
using allen key .
Important Note:
Make sure to
position the
backrest with the
arrow pointing
up as shown.
Attaching back rest
2
2
10
1
10
E
C
Step 3
Step 3
metal rod
1
2
2
10
C
C
a:
b:
10
arrow

Step 5
2
3
2
Attaching back rest
Note:The two bolts at this
stage is fully tightened
Then attach the back
frame into the chair
lift plate by inserting
into the slot hole as
shown.
Secure using the knob
and washer and tighten
by turning it clockwise.
Assembly Instructions
3
3
2
Step 6
6
Attaching castors
Attach the castors into
holes on the base and
secure by pressing down
firmly.
6
9
9
9
9
9
9
6

Assembly Instructions
7
8
6
Step 3
Step 7
Attaching gas lift
Insert the gas lift into
hole on the base as
shown & secure by
pressing down firmly.
Then insert the plastic
sleeve on the gas lift
.
7
8
8
6
7
Step 8
8
3
Attaching seat
Position the seat as
shown and insert the gas
lift into the hole on
the chair lift plate .
Secure by pressing down
the seat firmly.
3
8

8
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
Assembly is complete.
Gaslift operation
To adjust the seat higher,
pull up the lever under
the seat and release at
desired height.
To lower the seat, pull up
the lever while seated on
the chair.
Pull up lever
to adjust
seat height