ART+SOUND Tutto2.1 User manual

TM
Art_Sound
Optional: Using the compatible
ceiling brackets
• Remove the wall bracket attached to the satellite
loudspeaker.
• Slide the end of the wall bracket into the recess on the
ceiling bracket.
• The ceiling bracket may be slid into the recess on the
satellite speaker.
• The loudspeaker cable may be hidden in the hollow
space in the ceiling bracket.
• Secure this bracket by using the rubber end piece on
the satellite speaker.
Operating Manual
Tutto2.1
STEREO LOUDSPEAKER SET
SUBWOOFER
woofer dual-chamber
subwoofer
bass refl ex yes
dim. (h x w x d) 400 x 168 x 400mm
weight / piece 5,9kg
housing MDF
colour black or white
extra wall bracket, 4 feet
Tutto2.1
max power Ω 120W
max power (100V) 30 - 60W
frequency range 20 - 18kHz
options possible to connect
2 extra satellites
Satellite speakers may only be used in
combination with the Tutto1 subwoofer
SATELLITE SPEAKERS
mid-high 3” paper conus
dim. (h x w x d) 100 x 90 x 80mm
weight / piece 0,4kg
housing ABS, rubber fi nish
colour black or white
extra wall bracket
options ceiling bracket
Congratulations on your purchase of this stereo loudspeaker set.
Follow the instructions in this document to get the best possible results from this device.
We recommend that you keep these instructions for future use.
Check our website for any updates of this manual:
www.artsound.be
Discover the complete ArtSound
range at www.artsound.be
House Of Music nv
Tel. [phone]
Fax. [phone]
[email protected]
Warranty
2 years after date of purchase for normal use.
Invoice terms and conditions apply.

2 3
Tutto2.1Tutto2.1
400mm
80mm
40mm
40mm
15mm
270mm
164mm
400mm
TEMPLATE WALL BRACKET GURU1
Connecting 4 satellite loudspeakers
to the subwoofer (optional)
When connecting two pairs of satellite loudspeakers, the
marked SAT1 through SAT4 indicators must be used.
Also be sure to follow the indicated polarity.
Installing the subwoofer
• It is preferable to place the subwoofer close to the
walls that enclose the space. Make sure that the bass
tube is unobstructed.
• A corner set-up will generally result in a higher
reproduction of lower tones.
• The subwoofer module may be placed in a vertical as
well as horizontal position. However, never place this
in a position which causes the connections to face
upwards.
• The wall bracket (included) also provides the option
for mounting the device on the wall. The template
included indicates the position for mounting the wall
bracket to the module. Note: failure to follow the size
indications provided can cause permanent damage to
the subwoofer.
Packaging contents
• 1x subwoofer (Tutto1)
• 2x satellite loudspeakers (Tutto2)
• 2x wall brackets
• 1x wall bracket for subwoofer
• 4x spacer feet for wall mounting
• 4x bases to use as free-standing speakers
• 2x 8m loudspeaker cables
• 2x shrink sleeves for satellite loudspeakers
• screws for wall mounting
• 1x template for wall bracket subwoofer
• 1x cross screwdriver
INPUT
30W
100V 4Ω
STEREO
- CH1 + - CH2 +
- SAT1 +
- SAT2 +
STEREO
- +SAT 2
60W COM
OUTPUT
- +SAT 1
- SAT3 +
- SAT4 +
30W
60W
COM
INPUT
30W
100V 4Ω
STEREO
- CH1 + - CH2 +
- SAT1 + - SAT2 +
STEREO
- +
SAT 2
60W COM
OUTPUT
- +
SAT 1
- SAT3 + - SAT4 +
- +
- +
- +
- +
Naturally, every position involves making a compromise
between acoustic performance and aesthetic integration
of the subwoofer in the interior. It is advisable to conduct
several placement tests for the subwoofer to determine
which position will produce the best listening results. Just
like other listening tests, it is best to use audio material
that you are familiar with, and which has sufficient bass
content.
Setting up the satellite loudspeakers
• The two satellite loudspeakers enable every user to
create the most ideal stereo situation.
• When using the loudspeaker set in rooms with higher
than average ceilings (> 3 metres), it is recommended
to mount the satellite loudspeakers at a height of
approximately two metres above the ground.
• The wall brackets enable you to rotate the
loudspeakers 360° to create the most appropriate
sound direction.
• Please always mount the wall brackets using the
screws provided.
L
L
R
R
After completing the installation described
above, please tighten all of the screws in order
to get optimum enjoyment from this loudspeaker set.
The cover plate (included) must be replaced in order
to ensure your loudspeaker system works properly.
󰋾
󰋾
󰋾
STEREO CONNECTION
4 Ω(Low impedance)
CONNECTION 100V
(high impedance)
󰌥Make sure the switch
is set to "4Ω”
Be sure to take into account the polarity of both the
amplifier output as well as the indication on the bass
module.
• The L output channel may be connected to the “CH1”
indicator.
• The R output channel may be connected to the “CH2”
indicator.
Connecting satellite loudspeakers
to the subwoofer
• Remove the phoenix connector from the satellite
loudspeaker.
• Connect the loudspeaker cables to this connector,
following the indicated polarity.
• The left satellite speaker may then be connected
to the top SAT1 indicator, the right satellite speaker
to the lower SAT2 indicator.
Connecting the amplifi er
to the subwoofer
- +
L
- +
R
stereo amplifi er
INPUT
30W
100V 4Ω
STEREO
- CH1 +
- CH2 +
- SAT1 +
- SAT2 +
STEREO
- +SAT 2
60W COM
OUTPUT
- +SAT 1
- SAT3 +
- SAT4 +
󰌥Set the switch to
“100V”.
- +
L
- +
R
100V amplifi er
This loudspeaker set offers power options of 30W or
60W.
• Set the switch to “100V”.
• Connect the 100V output (+) of the amplifi er to the
30W or 60W connector depending on the desired level
of power.
• Connect the COM output (-) of the amplifi er to the
COM connector on the subwoofer.
If desired, several loudspeaker sets may be connected
to one another. In this situation, several subwoofers may
be daisy-chained provided you follow the indications for
the 30W/60W and COM connections.
However, make sure you always mount these at least six
metres apart in order to guarantee good results.
Depending on your personal preference, extra
adjustments to the bass from the amplifier may be
desirable.
Connecting satellite loudspeakers
to the subwoofer
see 'stereo connection 4Ω'
Connecting the amplifi er
to the subwoofer
FIG 1
Template for wall bracket subwoofer