Assa Abloy Sargent PE8893 User manual

1-800-727-5477 • www.sargentlock.com
Installation Instructions
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written
permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
WARNING
This product can expose you to
lead which is known to the state of
California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.
P65warnings.ca.gov.
Attention Installer: Improper
installation may result in damage
to the product and void the factory
warranty.
WARNING
Dummy Rail
PE8893 & PE8895 Exit Devices
A8320-1 5/23

2
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
Dummy Rail
Installation Instructions
PE8893 Exit Device
A8320-1 5/23
Screw Chart
DESCRIPTION
TOTAL QTY
SUPPLIED
WHERE USED
#10-24 X 3/4" FLAT HEAD
MACHINE SCREW
4
(4) CHASSIS
CORNER MOUNTING HOLES
(METAL DOOR)
#10 X 1-1/4" FLAT HEAD
WOOD SCREW
4
(4) CHASSIS
CORNER MOUNTING HOLES
(WOOD DOOR)
#10-24 X 3/4" ROUND HEAD
MACHINE SCREW
2
(2) REAR MOUNTING PLATE
(METAL DOOR)
#10 X 1-1/4" ROUND HEAD
WOOD SCREW
2
(2) REAR MOUNTING PLATE
(WOOD DOOR)
#8-32 X 5/16" W/ #6 OVAL HEAD
MACHINE SCREW
6
(4) CHASSIS COVER
(2) END CAP
1/4"-20 X 2-3/8" KNURLED FLAT HEAD
MACHINE SCREW
2
(2) EXIT TRIM
(IF USED)

3
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
Dummy Rail
Installation Instructions
PE8893 Exit Device
A8320-1 5/23
12
Measure 39-5/8” from the finished floor and mark
door and frame
Using a square, create a horizontal and vertical
centerline. Vertical centerline should be 2-3/4” off of
the edge of the door or centered on the door stile.

4
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
Dummy Rail
Installation Instructions
PE8893 Exit Device
A8320-1 5/23
4X 10-24 X3/4"
FLAT HEAD
SCREWS
56
4X 10-24 THREADED HOLES
34
Align supplied plastic template with the centerlines.
Mark chassis mounting holes.
Prepare chassis mounting holes. Refer to supplied
trim template as needed.
Install chassis using supplied mounting screws 10-24
x 3/4”. DO NOT FULLY TIGHTEN SCREWS.
Slide rail assembly onto the chassis.

5
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
Dummy Rail
Installation Instructions
PE8893 Exit Device
A8320-1 5/23
Ensure rail carrier tabs are aligned with the chassis, then fully tighten
the chassis screws.
7
8
Insert the end cap bracket into the rail assembly. Level the rail and mark mounting holds using the bracket as a
guide. Ensure rail overlaps door stile by 1/2”.
carrier tab

6
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
Dummy Rail
Installation Instructions
PE8893 Exit Device
A8320-1 5/23
Drill and tap end cap bracket holes 10-24
(2 places).
Install chassis and end cap cover using supplied 8-32 x 5/16” oval head screws.
910
11
Install end cap bracket using round head Phillips
10-24 x 1” screws, supplied.

7
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
Dummy Rail
Installation Instructions
PE8893 Exit Device
A8320-1 5/23

A8320-1 5/23
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written
permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.