Assa Abloy Liscio User manual

ASSA ABLOY, the global leader in door opening solutions
Installation Guide
ELECTRONIC KEYPAD LEVERSET WITH
BLUETOOTH PROGRAMMING

2
ITEM NO. DESCRIPTION QT Y.
1 Key 2
2 Outside Trim Plate Assembly 1
3 Adjustable Latch for 2 ⁄”or 2 ¾” Backset 1
4 Inside Trim Plate Assembly 1
4a Inside Chassis 1
4b Inside Trim Plate 1
4c #8-32 x ⁄" Flat Head Machine Screw 2
4d 9V Alkaline Battery 1
5 #8-32 x 1½" Flat Head Machine Screw 2
6 #8 x ¾" Wood Screw 4
7 Strike Plate 1
8 Plastic Extender 1
9 Plastic Latch Pin 1
3
4b
2
4a
4c
4d
5
7
6
4
8
9
1
6
What’s in the Box

3
2 ⁄” or 2 ¾”
Backset
2 ⁄” Dia
Bore
⁄” Deep
2 ¼”
1 “ 1” Diameter
Edge Bore
2. Door Prep 3. Door Jamb Prep
1. Conrm Handing
HANDING OF DOOR IS ALWAYS DETERMINED FROM THE OUTSIDE
Hinge is on the left.
Door is Left Hand (LH).
Hinge is on the right.
Door is Right Hand (RH).
Hinge is on the right.
Door is Right Hand (RH).
Hinge is on the left.
Door is Left Hand (LH).
In-Swing Doors Out-Swing Doors
outsideoutside
Preparation
1” Deep,
1” Diameter
Edge Bore
⁄” Deep
1-1/8"
2-3/4"
2 ¼”
1 ½”
Fasten Strike Plate using
two #8 x ¾” Wood Screws
(item #6).
4. Install Strike Plate
2⅜” Backset
Correct Hub Position
2⅜” Backset
Wrong Hub Position
2¾” Backset
Correct Hub Position
IMPORTANT!
CHECK LATCH HUB POSITION BEFORE INSTALLING

4
Use a Phillips head screwdriver to remove screws (item #4c) shown below and
detach Inside Trim Plate from the Inside Chassis.
Fasten Adjustable Latch using two #8 x ¾” Wood Screws (item #6).
2. Remove Screws from Inside Trim Plate
How to Install
!
!
REMOVE INSIDE
CHASSIS FROM
TRIM PLATE BEFORE
INSTALLING THE
OUTSIDE TRIM.
THUMBTURN MUST
BE IN NEUTRAL
POSITION.
To remove Pin:
Push Plastic Latch Pin (item #9)
through latch with screwdriver.
The Adjustable Latch is factory
shipped with a 2¾” backset
position. Remove pin and slide
spindle hub forward for a 23/8”
backset, then reinsert the pin in
the hole at the back of the latch
as shown.
1. Install Adjustable Latch
RH LH
See Page 3 for Handing
Information.
Scan QR code for
installation video
Plastic Latch Pin
Plastic
Latch
Pin

5
3. Install Outside Trim Plate Assembly
Step 1: While holding Outside Trim Plate Assembly, Press the Plastic Extender (item #8)
into end of Spindle Shaft.
Step 2: Position the Outside Trim Plate Assembly through the bore hole.
Step 3: With the Outside Trim Plate Assembly ush to the door, REMOVE the Plastic
Extender.
Feed wire harness
through the bore hole.
!
Fit Plastic Extender
through latch.
ONCE POSITIONED,
OUTSIDE TRIM PLATE
ASSEMBLY REQUIRES
SUPPORT.
THIS SIDE ON TOP.
!
TOP

6
4. Install Inside Chassis
CAM LINK MUST
REMAIN IN
THE CORRECT
POSITION DURING
INSTALLATION.
!
Step 1: Conrm the position of Cam Link.
For Left Hand Locks:
Turn to left position.
For Right Hand Locks:
Turn to right position.
Step 2: Feed the Wire Harness through Inside Chassis.

7
CHECK ALIGNMENT BEFORE
FULLY TIGHTENING SCREWS.
!
Step 4: Connect Wire Harness (A) and tuck Connectors as shown (B).
A
B
Step 5: Install Battery.
For optimal performance, always use a good quality battery.
9V Battery
Step 3: Fasten Inside Chassis using two
#8-32 x 1½” Flat Head Machine Screw
(item #5).

IN8-LISCIO-INST 08/04/2014
5. Install Inside Trim Plate
Screws (item #4c)
Fasten Inside Trim Plate using two #8-32 x ⁄”Flat Head Machine Screws
(item #4c).
*Neutral position is required for installation and removal of the Inside
Trim Plate Assembly.
!
USER CODES ARE LOCATED
ON THE INSIDE TRIM PLATE &
ON USER MANUAL.
Inside
Correct position for installation.
Thumbcam must be positioned
as shown (Neutral Position)*
!
Scan QR code for
installation video