Assa Abloy PEMKO LP200 Series User manual

Copyright © 2012, Pemko Manufacturing Co., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Pemko Manufacturing Co. is prohibited. LP200_INS • Rev 1 - 09.12
LP200 Series Sliding Door Hardware
Installation Instructions
800-824-3018 • www.pemko.com
Door Leaf Capacity - Up to 200 lbs.
Manufactured by
Hanger
Door
Hanger Strap Bolt
Turn clockwise to raise door
Lock Nut
Channel Body
Bolt must be level with top of hanger body
Slider Body
Height Adjustment Bolt
Allen Key
Channel Body Cover
Kit No.
LP200A/6
LP200A/8
LP200A/10
Material
/ 6'
aluminum track / 8'
aluminum track / 10'
aluminum track
Max Leaf Size
96" x 36" x 2"
96" x 48" x 2"
96" x 60" x 2"
200 lbs
max door weight
280A or
280AN Track
Shown at
highest
(min clearance)
position
1-1/8"
(33)
Guide 102N
H
To calculate the opening height (H) H = Opening Height - 1-7/8" (48mm)
Overhead Mount
1-3/8"
(35)
1-3/4" (44) Max.
1-1/2" (38) Min.
3/8" (9.5) Max.
1/16" (2) Min.
2" (51) Max.
1-3/8" (33) Min.
1/4
(6)
3/16
(5)
9/16
(14) 1/8" (3.2) Min.
7/16" (11) Max.
2-1/4"
57
281A Bracket
(optional)
2-5/8" (66) MAX
2-5/16" (59) MIN
Spacer
(if required)
Guide
106N/94
(optional)
94X Channel
(optional)
Side Wall Mount
280A or
280AN Track
Shown at
highest
(min. clearance)
position
3/8" (9.5) Max.
1/16" (2) Min.
2" (51) Max.
1-3/8" (33) Min.
1/8" (3.2) Min.
7/16" (11) Max.
5/32"(4) MIN
7/16" (11) MAX
9/32"
(7)
9/16"
(14)
Alternative Guide Arrangement
Requires an additional 102N guide.
Not supplied in kit.
Guide 102N
LP200A Kits Include:
LH100 Hardware Kits Include:
1 ea 280AN Aluminum Track
1 ea LH100 Hardware Kit
2 ea Low Head Room Units
2 ea End Caps
2 ea In-Track Clip Stops
1 ea Screw Pack
2 ea Low Head Room Hangers
1 ea 102N White Nylon Mortise Guide
1 ea Small Spanner
1 ea 4mm Allen Key

INSTALLATION INSTRUCTIONS
1
3
Assemble hanger.
Copyright © 2012, Pemko Manufacturing Co., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Pemko Manufacturing Co. is prohibited.
Overhead Mount
Side Wall Mount
1/2" (13)
7Fix both channel bodies into door.
2
5
Connecting end
Clip Stop
Insert hangers and
retaining stop.
6
8
4
Mortise door for door guide.
1/4" (6)
9/16"
(14)
C
L
Attach a plumb line to hanger. Place hanger inside
track. Using plumb line, mark the centerline of floor
channel.
Fit door guide.
LP200_INS • Rev 1 - 09.12
Place nut inside hanger body.
Thread locking nut onto bolt and
then screw bolt into the nut within
hanger. Leave a 1/2" clearance
between the base of the hanger
and bolt head, as shown.
Secure track.
Use one bracket or fastener at
each end of track and no more
than 3' in between.
1-9/16" x 8g
3/16" bolt x 21/32"
Route top of door
at both ends for
channel bodies.
=
=
1-1/4"
(32)
4-11/16"
(119)
1-3/32"
(25)
1-7/32"
(32)
9/16"
(15)
1-9/16"
(40)
4-1/16"
(102) 4-1/2"
(114) 4-17/32"
(119)
Locking Nut
Slider
Hanger
Strap Bolt
Ensure 102N guide is running
in the routed guide slot in the
base of the door.
Position and adjust door height.
Ensure
slider is in
highest position.
Adjust
door
height.