Assa Abloy SARGENT 10X Series User manual

1-800-727-5477 • www.sargentlock.com
A8286 04/21
Copyright © 2021 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission ofSARGENT Manufacturing Company is prohibited.
Installation Instructions
10X Line Cylindrical Lockset
Installation Instructions
• #2 Phillips screwdriver
2Package Contents
1Tools Required
• Push pin (provided) • 1/8" drill bit• 7/16" drill bit • 2-1/8" Bore •1" Bore
• 5/32" drill bit
1
2
6
2
5
7
8
9
10
11
12
15
3
4
13
14
16
Fig. Description
1 Inside lever handle
2 Rose/Scalp (2)
3 Screws - latch (2) #8-32 x 3/4"
4 Inside spring housing assembly
5 Screws - through-bolt (2) #10-32 x 1-1/4"
6 Lockbody assembly with mounting plate
7 Outside spring housing assembly
8 Cylinder spacer
9 Cylinder
10 Outside lever handle
11 Key
12 Push pin
13 Latch
14 Screws - strike (2) #12-24 x 3/4"
15 Strike
16 Strike box (Optional)
3Door Preparation
DOOR
FRAME
Desired
height
above
floor
Template
Backset must
match latch Door bevel
Figure 1
7/16" (11mm) hole
2-1/8"
(54mm)
hole
1-1/8"
(29mm)
2-1/4"
(57mm)
1" (25mm)
hole
5/32" (4mm)
2-3/4"
(70 mm)
Figure 2
IMPORTANT
• The accuracy of door preparation is critical for proper functioning and security of this lever handle lock. Misalignment can
cause premature wear and a lessening of security.
• Be sure to verify backset before marking and drilling door.
IMPORTANT: Deadlocking latch must stop on
strike when door is closed.
Strike
Strike Box
Attaching Screws
Strike Box
Attaching Screws
#8 -32 x 3/4"
#12 -24 x 3/4"
Figure 3
1. Use template A8290 to mark the door (See Figure 1).
2. Drill the door according to the template.
3. Verify the dimensions (See Figure 2).
4. Install the strike (See Figure 3)

2
Copyright © 2021 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
A8286 04/21
10X Line
Installation Instructions
Cylindrical Lockset
5Adjust Lock for Door Thickness (if necessary)
6Install Outside Assembly
To adjust lock to door thickness if other than 1-3/4”
(44mm) refer to Section 5.
Insert lockbody into door from outside making sure that
lockbody hooks latch case and retractor engages bolt
tail(s). See Figure 6.
DO NOT FORCE. (If lockbody does not engage latch easily,
check door preparation for errors.)
Latch bolt tail should be centered in depth of retractor. If
it is not, refer to Section 5 to properly adjust the lock for
door thicknesss.
Lock is factory preset for 1-3/4" (44mm) doors unless specified. To adjust
lock to door thickness if other than 1-3/4" (44mm):
1. Remove trim assembly from the lockbody. (See Figure 5).
2. Rotate mounting plate to adjust for proper door thickness.
• For 2" thick door the inside face of the mounting plate should be
flush with the face of the bearing. (See 5a).
• Verify correct position from the markings on the through-bolt
stud, or by measuring from inside surface of the mounting plate to
the centerline of the retractor (See 5b).
3. Reassemble the outside trim assembly to the lockbody.
4Latch Installation
Install screws (2) #8-32 x 3/4".
Figure 4
Spin the mounting plate to the left to
adjust for larger door thickness.
Figure 6
Trim Assembly
Figure 5
Figure 5a
Door Thickness Dimension A
1-3/4" (44 mm) 7/8" (22 mm)
2" (50 mm) 1" (25 mm)
2-1/4" (57 mm) 1-1/8" (29 mm) Figure 5b
Centerline
of retractor
Retractor
Dimension A
Bearing
These
surfaces
flush
Mounting Plate

3
Copyright © 2021 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part
without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
A8286 04/21
10X Line
Installation Instructions
Cylindrical Lockset
7Install Inside Components
1. Remove rose from inside spring housing assembly.
2. Align and insert inside spring housing onto the installed lockbody.
3. Install screws to tighten the lock to the door.
4. Orient dimples on the side of the rose horizontally at 3 and 9 o’clock position in line with the openings on the spring
housing assembly. See Figure 7.
5. Install rose onto the inside spring housing assembly.
6. In the unlocked position, verify the button is adjusted properly. See Figure 8 for proper alignment. Adjust if necessary.
7. Install inside lever.
8Cylinder Installation
Cylinder spacer should
be installed “snapped”
on to the cylinder be-
fore installing into the
outside trim assembly.
Correct Key Orientation
During Assembly
Outside Lever
Cylinder
Cylinder Spacer
IMPORTANT
Before installing cylinders:
• Use a flat blade screwdriver to rotate cam until the driver points are in a 6 and 12 o’clock position. See Figure 15 on page 5.
a Standard Cylinder (Figure 9)
Screws (2) #10-32 x 1-1/4"
Figure 7
Button in-line with shank indicates
correct position based upon door
thickness. If the button needs to be
adjusted, position it by depressing
the plunger, moving it in or out as
needed.
Figure 8
Figure 9
Key
Rose dimple
Rose dimple opening
Note: Test for proper operation before closing door.

4
Copyright © 2021 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
A8286 04/21
10X Line
Installation Instructions
Cylindrical Lockset
8Cylinder Installation, continued
C
C
New Core
• Remove temporary construction core or plastic core. If keyed, use Control Key
(stamped “C”) rotate 15° and pull.
• Insert permanent core into lever with control key; rotate 15° and remove key.
SFIC
b Interchangeable or Removable Core (Figure 10)
IMPORTANT
• Remove tailpiece from construction core and insert into new core. If using 7 pin cores,
insert the 7 pin tail piece that’s supplied with the lock, before installing the core into the
lock.
• For XC LFIC cores, snap-on retainer must be installed onto tailpiece. Tail and retainer
assembly will press fit onto back of core.
Remove
Construction Core
Install New/
Final Cylinder
Remove/Reuse 6 Pin Tailpiece
Plastic Core
7 Pin
In Core
Keyed
Core
Construction Core
Keyed
Core
6 Pin
In Core
To Remove:
Rotate key 45° and hold. Depress lever catch with pin tool.
Lever catch
To Remove:
Remove core and tailpiece, using control key (stamped “C”).
Insert slotted screwdriver or lever release tool into the cylinder
opening and make contact with the lever catch.
To Remove:
Depress lever catch with pin tool, remove lever.
To Install:
Slide lever on over the lever catch. Confirm the lever will not
pull off.
a Standard Cylinder (Figure 11)
b Interchangable or Removable Core (Figure 12)
c Plain Lever (Figure 13) & Push/Turn Button (Figure 14)
Control Key*
To Install:
With driver points at 6 and 12 (See Figure 15), rotate key 45° in either
direction, and then slide the lever on over the lever catch. Confirm the
lever will not pull off.
Pull lever catch horizontally towards the opposite side of the cylinder
opening and remove lever. *Note
For 1-Bitted cylinders, utilize a control key cut 113511.
9Lever Removal & Installation
Figure 11
Figure 12
Figure 13 Figure 14
Figure 10
XC LFIC
To Install:
Without the core installed, slide the lever over the lever catch. Confirm the lever will not pull off. Install core and tailpiece,
using control key (Stamped “C”).

5
Copyright © 2021 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part
without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
A8286 04/21
10X Line
Installation Instructions
Cylindrical Lockset
11 Other Instructions
a Remove Outside Lever for Exit Latch 10XG13
1. Remove inside lever (See Section 9).
2. Remove rose.
3. Remove (2) mounting screws and inside housing assembly. See Figure 16.
4. Remove outside trim assembly.
5. Push and hold plug back (located inside of outside trim assembly). See Figure 17.
6. Push lever catch with push pin and remove lever.
Remove
Push Push and Hold Plug
(2) Mounting Screw
Inside Housing Assembly
Lever
Rose
Outside Trim Assembly
Figure 16
Figure 17
10 Timing 10XG26 & 10XG38
1. Remove outside and inside levers (See Section 9).
2. Adjust cams visible from both the outside and inside lock trim.
2a. Use a flat blade screwdriver to rotate each cam until the driver
points are in a 6 and 12 o’clock position. (See Figure 15)
3. Re-install outside and inside levers.
4. Test both cylinders with key before closing the door.
Figure 15
View into lock from
end of trim
12 o’clock drive point
6 o’clock drive point

6
Copyright © 2021 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
A8286 04/21
10X Line
Installation Instructions
Cylindrical Lockset
11 Other Function Instructions, continued
Outside Trim Assembly
Screws (2) #10 - 32 x 1-1/4"
Cup Washer
Inside Trim Assembly
Figure 18
Figure 19
Inside Trim Assembly
12 Miscellaneous Options
a 1-3/8" Doors (1- Option)
Outside Trim and
Lockbody
Adapter Plates
Inside Trim Assembly
Install (1) adapter plate between the door and rose assemblies (both sides).
• Inside trim to be aligned with holes marked screw slot.
• Outside trim through-bolts to be aligned with through-bolt holes marked on adapter plate.
b Install Single Lever Pull 10XU93
c Install Double Lever Pull (10XU94/ 10XU94-2)
Screws (2) #10 - 32 x 1-1/4"
Used with 10XU94-2 only

7
Copyright © 2021 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part
without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
A8286 04/21
10X Line
Installation Instructions
Cylindrical Lockset
12 Miscellaneous Options
Tailpiece
1. Provided less core.
2. Tailpiece included with lock.
3. Attach tailpiece to Schlage® LFIC and insert into the lever.
1. Provided less core.
2. Depress cap pin and unscrew end cap to
remove tailpiece from competitor cylinder.
3. Insert new tailpiece, in orientation shown.
4. Re-assemble end cap over new tailpiece.
b Lever to Accept Schlage®LFIC (SF- Option)
c Lever to Accept Schlage®or Yale®Fixed Core Cylinder (30- or YC- Option)
d Lever to Accept Yale®LFIC (YRC- Option)
Competitor’s
Cylinder
Cap Pin
End Cap
1. Provided less core.
2. Slide provided spacer over tailpiece
3. Insert driver assembly into back of core.

A8286 04/21
1-800-727-5477 • www.sargentlock.com
Copyright © 2021 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission ofSARGENT Manufacturing Company is prohibited.
WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information go
to www.P65warnings.ca.gov.
12 Miscellaneous Options
e 10XG50 Hotel Function Adjustment
1. Remove lever, cylinder and spacer from assembly.
2. Insert adjustment tool (provided with lock) into interior cap as shown below.
4. Rotate back counter-clockwise until tool handle is approximately in line with the end of the shank (as shown) AND cap slot
orientation is vertical. Slot alignment may require a slight rotation in either direction.
5. Remove adjustment tool and re-install cylinder and lever. Lever install will require key be rotated 90° counter-clockwise.
3. Rotate cap clockwise until fully tight.
- To adjust timing of hotel cylinder key lockout indicator
cap