Assa Abloy Sargent 8200 Series User manual

1-800-727-5477 • www.sargentlock.com
A8260D 11/21
Installation Instructions
7800 & 8200 Series Mortise Lock
Used with VN1 Escutcheon Trim and V Series Indicators
Copyright © 2019, 2020, 2021, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express
written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
WARNING
This product can expose you to
lead which is known to the state of
California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.
P65warnings.ca.gov.
Attention Installer: Improper
installation may result in dam-
age to the product and void the
factory warranty.
WARNING

2
1-800-727-5477 • www.sargentlock.com A8260D 11/21
7800 and 8200 Series Mortise Lock
Installation Instructions
Used with VN1 Escutcheon Trim and V Series Indicators
Copyright © 2019, 2020, 2021, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
Tools Required
1
TOC Table of Contents
1 Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 Indicator Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3 Lock set configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4 Rehanding Indicator (if required). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
a Prepare Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
b Install Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
c Install Outside Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
d Install Inside Trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
e Install Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
f Install Outside Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
g Perform Functional Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
h Indicator Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
#2 & #3 Phillips
head screwdrivers
Flat blade
screwdriver
1/8”Allen
Wrench
3/32"Drill bit T-20 Torx Screw
with Tamper Pin
Driver

3
1-800-727-5477 • www.sargentlock.com
7800 and 8200 Series Mortise Lock
Installation Instructions
Used with VN1 Escutcheon Trim and V Series Indicators
Copyright © 2019, 2020, 2021, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
A8260D 11/21
Indicator Variants
2
Depending on function and option ordered, indicators are provided in
the following variations, these instructions detail how to install with
cylinder, however other variations follow similar instructions. (Figure1)
Contact factory for any questions.
Coin Turn - For
installation
on outside of
door.
Cylinder - For
installation
on inside or
outside of
door.
No input /
blank - For
installation
on inside or
outside of
door.
Thumbturn -
For installation
on inside of
door.
Figure1
Lock set configuration
3
To set function of multi-function lock or to re-hand, see instructions on
lock body.
Rehanding indicator (if required)
4
Indicator spindle cams MUST be oriented correctly per lock function and
door mounting location. Verify hand and bevel of door. (Figure2)
LH
Left Hand
Hinges Left
Open Inward
RH
Right Hand
Hinges Right
Open Inward
LHRB
Left Hand
Reverse Bevel
Hinges Left
Open Outward
RHRB
Right Hand
Reverse Bevel
Hinges Right
Open Outward
Figure2
Note:
Stand on outside of locked door when determining door hand.
Next, verify inside and/or outside indicators are handed correctly,
using Spindle Cam Position chart. (Figure3) If they are handed
correctly, skip to Step 5 "Prepare Door".
If they are not handed correctly:
1. Remove retaining pad and spindle cam from assembly. (Figure4)
2. Position spindle cam in correct direction for door hand. (Figure3)
Important:
• For thumbturn indicators, make sure thumbturn
is positioned in the 12 o’clock direction as
shown. (Figure5)
3. Slide spindle cam post into correct slot of display slide. (Figure4)
4. Re-seat retaining pad into original position.
5. Return indicator to the vacant/unlocked position for installation.
Scan this QR
code for the
Sargent Indicator
Handing Charts
Door Hand: RH / RHRB
Door Hand: LH / LHRB
Outside Indicator
Inside Indicator
Inside Indicator
Outside Indicator
Spindle Cam Position for Locks with Deadbolt (*and 56 function)
Door Hand: RH / RHRB
Door Hand: LH / LHRB
Outside Indicator
Inside Indicator
Inside Indicator
Outside Indicator
Spindle Cam Position for Locks without Deadbolt (*except 56 function)
Figure3
Figure4
Spindle
cam
Display
slide slot
Retaining
pad
Thumbturn
position
Figure5

4
1-800-727-5477 • www.sargentlock.com A8260D 11/21
7800 and 8200 Series Mortise Lock
Installation Instructions
Used with VN1 Escutcheon Trim and V Series Indicators
Copyright © 2019, 2020, 2021, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
aPrepare Door
bInstall Lock
Installation
5
Figure6
Prepare door for function holes, size, and location according to A8258 door
marker template, if not already prepped.
1. Verify strike location according to template. Clean out door pocket and door edge of debris.
2. Ensure handing of lock matches handing of door. Slide lock into door. (Figure6)
3. Temporarily hand tighten two (2) lock screws (#12 x 1-1/4"wood screws, or #12-24 x1/2"machine screws).
Notes:
• Keep door open until installation is complete.
cInstall Outside Trim
dInstall Inside Trim
Inside of door
Lock
Lock
Screws
Outside
of door
RH door
shown
1. Verify lock is in unlocked state (control hub slot should be vertical).
Also, verify indicator is in vacant/unlocked position.
2. Align trim posts with diagonal holes in door, be sure lever is horizontal. Slide outside
escutcheon assembly through lock body from outside door face. (Figure7)
Note:
If indicator is used on outside, align indicator spindle with control hub. Outside Escutcheon Assembly
Figure7
1. Slide spindle into lockbody hub. (Figure8)
2. Slide adapter and plate assembly over spindle.
3. Secure with two (2) #8-32 x 5/8" screws.
4. For Studio Collection levers only, use trim bushing over adapter plate.
5. Verify lock is in unlocked state (turn outside lever to ensure).
Also, Verify indicator is in vacant/unlocked position.
6. Align escutcheon over adapter and install inside escutcheon assembly onto
inside door face.
Note:
• If indicator is used on inside, align indicator spindle with control hub.
7. Through-bolt inside escutcheon to outside escutcheon with
two (2) #8-32 x 2-1/4"screws.
8. Install inside lever on adapter plate. Secure with set screw.
Note:
Screw heads should be visible on inside escutcheon.
Figure8
Inside
Escutcheon
Assembly
Studio
Collection
Trim
Bushing
Adapter Plate
Spindle
Lever
Set
screw
#8-32 x 2-1/4" screw
#8-32 x
2-1/4"
screw
#8-32 x
5/8" screws

5
1-800-727-5477 • www.sargentlock.com
7800 and 8200 Series Mortise Lock
Installation Instructions
Used with VN1 Escutcheon Trim and V Series Indicators
Copyright © 2019, 2020, 2021, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
A8260D 11/21
Installation, continued
5
eInstall Cylinder
fInstall Outside Front
1. Thread cylinder into lock until flush with escutcheon surface. (Figure9)
• Pull key slightly out of cylinder to help thread into lock body.
2. Tighten cylinder clamp screw with #1 Phillips screwdriver.
• Check operation and adjust cylinder if necessary.
Notes:
• SARGENT logo must be horizontal and on top. (Figure10)
• If double cylinder function is used, repeat steps 1 and 2 for second cylinder.
• Removable Core or Interchangeable Core cylinders require a control key (key
stamped with C) to remove and install the core. This is not provided standard;
it must be requested separately. If requesting 1-bitted control key, specify
113511 cut.
Cylinder
Cylinder
Clamp
Screw
Figure9
Incorrect
Key and cylinder must be rotated as shown.
Correct
Figure10
1. Tighten the two (2) lock screws completely. (Figure11)
2. Attach outside front with two (2) flat head screws #8-32 x 1/4".
gPerform Functional Check
DO NOT FORCE if resistance is encountered during functional check.
Refer back to Rehanding Indicator (if required) section to ensure
correct handing. Rehand if necessary.
1. Insert key into cylinder (if present) and rotate:
• Ensure there is no friction against lock case or any other obstructions.
2. Check key retracts latch:
• Key should rotate freely.
3. Throw deadbolt (if present):
• Check key retracts both deadbolt and latch.
4. Test levers:
• Confirm latch and deadbolt (if installed) retract.
5. Verify indicator displays correct status when locked and unlocked.
Figure11
Lock
screw
Outside
front
Lock screw
#8-32 x
1/4" screws

6
1-800-727-5477 • www.sargentlock.com A8260D 11/21
7800 and 8200 Series Mortise Lock
Installation Instructions
Used with VN1 Escutcheon Trim and V Series Indicators
Copyright © 2019, 2020, 2021, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
Indicator Parts List
6
* These parts are for 1-3/4"standard thickness doors. For other thicknesses, please contact factory.
Note:
Reference 8200 Series parts manual for all lock body parts.
4A
4B
4C
Figure12
Figure12 Description Part Number Req.
1 VN1 Indicator Escutcheon Consult Factory 1
2 Indicator Window 81-0811 1
3
Indicator Display Assembly - Green Unlocked / Red Locked 82-5602
1
Indicator Display Assembly - Green Vacant / Red Occupied 82-5603
Indicator Display Assembly - Green Unlocked Icon / Red Locked Icon 82-5604
Indicator Display Assembly - White Unlocked / Red Locked 82-5605
Indicator Display Assembly - White Vacant / Red Occupied 82-5606
Indicator Display Assembly - White Unlocked Icon / Red Locked Icon 82-5607
4A Indicator Spindle Cam - Thumbturn / Coin Turn 81-0745 1
4B Indicator Spindle Cam - Cylinder / No Input / Blank 81-0756* 1
4C Indicator Spindle Cam - 05, 37, 38, 59 Functions 81-5577* 1
5 Indicator Backing Plate 81-0748 1
6 VN1 Escutcheon Screw Pack (Not shown) 82-5587 x finish* 1
7 Door Marker Template (Not shown) A8258 1

7
1-800-727-5477 • www.sargentlock.com
7800 and 8200 Series Mortise Lock
Installation Instructions
Used with VN1 Escutcheon Trim and V Series Indicators
Copyright © 2019, 2020, 2021, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
A8260D 11/21

WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information go
to www.P65warnings.ca.gov. A8260D 11/21