Assa Abloy 7003 User manual

Product Layout:
2
User Manual
7003 Smart Door Lock
3
.
Panel and lock body installation steps.
1. Adjust latch direction according to door opening side.
2. Lock body: Put lock body into hole made then tighten screw.
3. Put M 5 stud on front rose and use screwdriver tight it, data line and spindle go
thought lock body together properly and data line go thought back handle, then tight
M4*35 screws on back rose, last test lock body latch and bolt should work well.
4.Connect front data line onto port at back handle and put 4*AAA battery into handle,
after heard: “Du” means connected, last put battery cover on handle properly.
5. Put M 5 stud on front rose for cylinder then hole made for it and back rose should be
connect with right position then tight M4*35 screws. Cylinder go thought rose and
screw in cylinder screw on liner.
6.Install buckle plate and buckle box on frame, make sure bolt and latch work smoothly.
7. Try handle & lock body see if work smoothly otherwise check again until work well.
Change battery by using A screwdriver from back handle
Front rose back rose
Function button
Please keep internal/external panel clean before installation.
Lock body change direction
Handle change direction
latch
Latch adjust parts Commutate
lock body
liner
Pull spindle out and turn 180 degree
Inside Handle Outside Handle
Rose
1.When installing lock
sure batch bolt should
always on top and dead
bolt at.
2.Please adjust latch bolt
slope when necessary.
a.Latch bolt commutator
follow arrow direction that
push latch bolt in adjust it
as required.
b.Turn latch bolt 180° and
take it out from liner after
adjusting.

Product Features:
● Multiple way to access: Fingerprint & Mechanical Key.
● Fingerprint: Advanced semiconductor sensors with 360° scanner.
● Lock can have fingerprint access users capacity: Fingerprint ( 2 master users & 28 normal
users).
● Reminder: Unlock, low battery and up to lock voice.
● External power supply: Can use power bank with 5V for emergency power supply.
Operations:
1. Reset factory default: Press function button at back of lock for 5 seconds, voice will prompt
reset succeed.
2. Register master/user:
2.1 Initial mode: Short press function button at back handle 1 time voice promote add master.
2.2 Once master user is added: Short press function button at back handle 1 time, input any
registered master at this time can add 1 more master( if only 1 master registered) or common
user.
3. Delete registered fingerprint:
3.1 Short press function button at back handle 3 time, confirm any registered master and input
master or user need to be deleted, until heard succeed.
Other function:
1. Internal Forced Lock: Short press function button 2 times, voice promote locking,
at this time only master and key can unlock
2. On/Off unlocking mode:
2.1 After master open and pres function button at back 1 time within 6 second,unlocking
mode on.
2.2 By using mater open 1 time unlocking mode will off.
3. Turn off voice: Short press function button at back for 4 times, voice promote will be off.
4. Electricity quantity Checking and series checking: Short press function button at back for
5 times, voice will promote ( low / medium/high battery) and series no.
How to take battery cover out:
1. After installation of lock please reset lock to factory default mode.
2. After factory default mode make sure to register 1 master user.
3. The handle is the key part for opening and closing door, and its flexibility ratio directly
influences the usage of door lock, hence, don't hang articles on handle.
4. Gently press fingerprint on the fingerprint sensor for registration of fingerprint.
Please don't press with great force to prevent scratching the fingerprint sensor.
5. This lock uses 4 AAA high-energy alkaline batteries (1.5V). When it prompts "the
voltage is low, please replace battery" for the first time, the door can be opened for
about 100 times as per different battery capacities; At this time, the battery should be
replaced promptly to avoid inconvenience due to the exhausted battery.
Remark:
1. All fingerprint need to scan 3 times for addition.
2. After successful registration press function button at back to exit.
3. When Deleting fingerprint, one master user in fingerprint has to be left.
Remark:
4 5
When change battery use slotted screwdriver push in
and up towards door direction.