Assa Abloy Norton 8000 Series User manual

Copyright © 2004, 2017 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2217-020 Rev 2 (09-17)
ASSA ABLOY
Installation Instructions
1
Left Hand Door - LH
Right Hand Reverse - RHR Right Hand Door - RH
Left Hand Reverse - LHR
Regular Arm Installation
Adjustable (Sizes 1 thru 6)
S8101
S8301
S8501
Non Hold Open Models
8000 Series
Non Handed Door Closer
• "DA" suffix (Delayed Action) is an optional feature.
• NOTE: For special applications a separate door and frame preparation template is packed with these instructions.
Use this instruction sheet for installation sequence and closer adjustments only.
• Doors should be hung on ball bearing or anti-friction hinges.
• A separate door stop is recommended.
• Door and frame must be properly reinforced.
• Always adjust spring power before adjusting control valves.
• Adjust closing time speed between 3 and 7 seconds from 90° to 0°. Greater closing times may be required for
elderly or handicapped.
• These door closers should NOT be installed on the exposed side (weather side) of exterior doors.
An Incorrectly installed or improperly
adjusted door closer can cause property
damage or personal injury. These
installation instructions should be followed
to avoid the possibility of misapplication or
misadjustment.
!

Copyright © 2004, 2017 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2217-020 Rev 2 (09-17)
2
3/16"
#7
1/4-20
for Wood drill 7/32
Machine Screws
#7 Drill, 1/4-20 Tap
Metal Wood Self Drilling Screws
Wood and Metal
For Wood drill 3/16 hole
* Pilot Hole
Required
Sleeve Nut and Bolt
Thru Bolt and Grommet Nut
Drill 9/32 thru from Closer Side
3/8 Drill other side
Drill 9/32 thru from Closer Side
3/8 Drill other Side
(Optional)
Screw Pack
Regular Arm/Top
Jamb Shoe
Connecting Rod
Forearm
Screw
Main Arm
Closer Arm
Backcheck Valve Power Adjustment Shaft
Latch Valve
Sweep Valve
Closer Body
Cover Clips
Cover Screw
Cover Screws
Metal Cover
Standard With
8500M Series
8400M Cover
Cover Screw
Cover Screws
Standoffs
Architectural Metal Cover
Standard With 8500MA Series
8400MA Cover
Pinion Cap (1639)
Insert Cutouts
Cover
Insert
Standoff
Standoff
Architectural Plastic Cover
Standard With 8500A Series
8400A Cover
Cover
Insert
Insert Cutouts
Full Cover
Standard With 8500 Series
8400P Cover
Narrow Cover
Standard With 8300 Series
8200P Cover
Mark and Drill Holes
Non Hold Open Door Closers — Regular Arm
8000 Series
ŸDo not scale drawing.
ŸRight hand door shown, left hand opposite.
ŸDimensions are in inches / (mm)
ŸHollow metal door require channel or box type reinforcement
when through bolt mount is specified.
ŸSex bolts required for wood or plastic faced fire door
mounting.
ŸMinimum thickness recommended for reinforcements in
hollow metal doors and frames: .146" (2.66mm) unless
otherwise specified.
Opening
Dimension “A”
Inches
mm
To 100°
7-1/2
191
100° to 130°
6
152
131° to 180°*
4-1/2
114
1-1/4
(32)
3/4
(19)
A
5-1/2
(140)
1-3/4
(45) 1-1/8
(29)
12"
(305)
Centerline
of Hinge or Pivot
C
L
Frame Rabbet
Door Top
2-9/16
(65)
1-5/8
(41)
Cover
2-1/8
(54)
3-11/16
(94)
3-0
(76)
This template for use with standard butt hinges or 3/4 offset pivots.
For all other hardware, please consult factory for template.
*Door/Frame/Hardware/Wall conditions permitting.

Copyright © 2004, 2017 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2217-020 Rev 2 (09-17)
3
Non Hold Open Door Closers — Regular Arm
8000 Series
Pinion Cap or Optional Cover
or
(2)
Installation Sequence
8300 Series
Screw pinion cap onto pinion shaft by hand or
with a Phillips screw driver - DO NOT OVER TIGTHEN.
*Optional 8500M
Metal Cover Installation
2 Cover
Screws
8400M Cover
2 Clips for metal
covers 8500M
1
6
4
7
Optional
For
8500 Architectural
Cover Only
90°
5
*For Optional 8500M
Cover, install clips
before securing
closer to door.
Arm Placement in Shoe
or
or
7-1/2 % stronger
7-1/2 % weaker
-
+
3
2
L
Y
S
Z
R

Copyright © 2004, 2017 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2217-020 Rev 2 (09-17)
4
ASSA ABLOY
8000 Series
Spring Power Adjust
Adjustment Chart
EXTERIOR
INTERIOR
Regular Arm
FULL 360° TURNS
OF 5/16 POWER
ADJUSTMENT
WRENCH
S8101/S8301/S8501
DOOR
*32"
(0.85M)
36"
(0.90M)
42"
(1.00M)
48"
(1.20M)
5811 13
710 13 16
20 FULL (360°) TURNS MAXIMUM AVAILABLE
*
MAXIMUM DOOR SIZE
Number of Turns Required
Closer is shipped set at mid range setting = 10 turns
The closing force for series 8101, 8301 & 8501 door closers is adjustable
from a size 1 to a size 6, as outlined in ANSI Standard A156.4.
When these series of door closers are installed and adjusted to
conform to ADA reduced opening force requirements (5 lbs max.) for
interior doors, they may not have adequate closing force to reliably
close and latch the door. Power adjustments charted on this page are
recommended where possible, to ensure proper door control.
By law the Americans with Disabilities Act (ADA) may
require that door closer installation comply with
accessability guidelines.
!
+
-
(Use 5/16” Socket or
Adjustable Wrench for
this Adjustment)
CLOSED
70°
10°
(Use 1/8" Hex Wrench
for these Adjustments) Adjust Closing Speed Time to between 3
to 7 seconds from 90°. Use of the door
by handicapped, elderly or small children
may require greater closing time.
!
Backcheck
+
-
Latch
Sweep
Delayed Action
(Optional)
-
+
-
+
+
-
To Identify Date Code:
Mfg.
Date
1FA
3000 Highway 74 East • Monroe, NC 28112
Tel: [phone] Ext. 4706 • Fax: [phone]
www. no r tondo or co nt ro ls .c om