Assa Abloy Lockwood 5831 Series User manual

We take the worry out of
protecting what’s valuable to you.
Lockwood: no worries®
www.lockweb.com.au
5831 Series Low Energy Operator

2Lockwood Product Catalogue | 5831 Series Low Energy Operator
1300 LOCK UP (1300 562 587) lockweb.com.au
5831 Series Low Energy Operator
Table of Contents
How It Works, Application Images ................................... 4
Product Descriptions, Features....................................... 5
Functions............................................................ 6
Touchless Solutions ................................................. 6
5831 Selection Guide................................................ 7
Low Energy vs Full Energy Operators ............................... 7-9
Wireless Interface Module ..........................................10
Product Dimensions ................................................11
Accessories.........................................................12
Kits.................................................................13
How to order .......................................................14
As one of the world’s only regenerative power door operators, The
Lockwood 5831 Series is a heavy duty, low energy door operator designed
for moderate to heavy use traffic. An on-board lithium battery eliminates
the need for electrical power. Available in wireless and plug-in versions
and able to fit in the tightest of spaces, the 5831 Series is simple to install
and use.
A simplified solution in automating an existing door in varying applications.

5831 Series Low Energy Operator
3
Lockwood Product Catalogue | 5831 Series Low Energy Operator
1300 LOCK UP (1300 562 587) lockweb.com.au
SAFETY MESSAGE:
The 5831 Series Swing Door Operator, like any powered appliance, has the potential to cause serious
harm and injury.
Its important that the product is installed in accordance with the supplied instructions and where
needed, any power connection be carried out by a qualified electrician.
Correct programming of the unit is necessary to ensure pedestrian safety.
ASSA ABLOY Opening Solutions recommends the use of finger protection guards where appropriate.
• WARNING - KEEP BATTERIES OUT OF REACH OF CHILDREN
• If the battery is a lithium button/coin battery placing the battery in any part of the body or swallowing
may lead to serious injury in as little as 2 hours or death. Including, but no limited to choking hazard,
chemical burns, or potential perforation of the oesophagus (if swallowed).
• If the battery is a non-lithium button/coin battery placing the battery in any part of the body or
swallowing may lead to serious injury.
• Ifyoususpect yourchildhasswallowed or inserted abuttonbattery,seekmedical attentionimmediately.
o Australia: Call the Poisons Information Centre immediately on 13 11 26 for 24/7 fast, expert
advice. If your child is having any difficulty breathing, contact 000.
o New Zealand: Call the National Poisons Centre immediately on 0800 POISON (0800 764 766)
for 24/7 fast, expert advice. If your child is having any difficulty breathing, contact 111.
• Examine devices and make sure the battery compartment is correctly secured, e.g., that the screw or
other mechanical fastener is tightened. Do not use if compartment is not secure.
• Dispose of used button batteries immediately and safely. Flat batteries can still be dangerous. As soon
as you have finished using a button battery put sticky tape around both sides of the battery. This will
make them less attractive to children and to avoid the low risk of them catching fire. Then dispose of
them immediately in an outside bin, out of reach of children, or recycle safely.
• Tell others about the risk associated with button batteries and how to keep their children safe.

4Lockwood Product Catalogue | 5831 Series Low Energy Operator
1300 LOCK UP (1300 562 587) lockweb.com.au
5831 Series Low Energy Operator
Push Side Mounting without electrical power Push Side Mounting with 1015T/24V Hardwire Kit
Pull Side Mounting without electrical power Pull Side Mounting with 1015T/24V Hardwire Kit
How it works
How does the 5831 Series work without electrical power?
The 5831 Series is a heavy duty, low energy door opener
designed for moderate to high traffic manual opening
applications that occasionally require powered operation.
A regenerative drive system charges an onboard battery
pack eliminating the need for electrical power.
When considering the 5831 Series Low Energy Operator, it’s
recommended to use the 80/25 guideline - 80 manual cycles
or more per day and is used 25% or less automatically.
When applied using the 80/25 guideline, the operator
will self generate all the power it needs to keep its field
replaceable, onboard battery pack charged.
A fully charged battery has the capability to open a door
up to 2000 times in a row, generously allowing for periodic
fluctuations from 80/25 guidelines with little impact on the
product’s overall usability. Example: 30% automatic use for
one day is not a problem, as long as that level of automatic
use is not sustained.
The 5831 Series Low Energy Operator can be used outside of
the 80/25 parameters. Simply plug the unit into a common
240V AC electrical outlet using our 1015T/24V Hardwire Kit
option. The Hardwire Kit is a low voltage plug in transformer
and can be added to existing installed field units.
Note: ASSA ABLOY Opening Solutions recommends that any unusable, discharged batteries
are disposed of in the correct way through a specialist battery recycling service or Local
Government Authority. Please DO NOT dispose of through regular recycling or waste facilities.

5831 Series Low Energy Operator
5
Lockwood Product Catalogue | 5831 Series Low Energy Operator
1300 LOCK UP (1300 562 587) lockweb.com.au
5831 Low Energy Operator - Push Side
• No electrical power required.
• Moderate to high traffic, manual opening applications that
occasionally require automatic operation.
• Regenerative Drive System charges an onboard battery pack.
• The 5831 Series excels in applications where the traffic
pattern allows for 80 door cycles per day, 25% of which
are automatic and 75% of which are manual. It requires no
electrical connection, no permit, no inspection, no wiring,
and no low voltage license.
• Installed similar to a manual door closer in less than an hour.
• A scalable solution in either Regenerative or Powered modes.
• Integrates into existing Access Controlled environments.
Features
• Regenerative drive or continuous duty operation
• 5° door opening
• Push Side mounting - standard
• Push-and-Go (ADA1015T/24V Kit must be connected)
• Power Close (ADA1015T/24V Kit must be connected)
• Latch Assist
• Executive Mode Feature
• Radio Frequency stainless steel push buttons
• Integral RF receiver
• Shock absorbing arm
• 24VDC input port
• ADA1015T/24V hardware kit
(Optional and to be ordered separately)
• Built-in ON/OFF Switch
• Auxiliary activation input port
• Maximum door width - 1200mm
• Maximum door weight - 110Kg
• Patented Auto-Tune feature ensures safety
• 2 year limited warranty

6Lockwood Product Catalogue | 5831 Series Low Energy Operator
1300 LOCK UP (1300 562 587) lockweb.com.au
5831 Series Low Energy Operator
Functions
Touchless solutions
Complete your touchless environment with a simple door
opening upgrade, designed for both ease of access and
optimal hygiene control.
The 5831 Series offers a simple solution for upgrading a
variety of doors to operate hands-free.
Wave-to-Open switches paired with the 5831 Series
Low Energy Operator allow building occupants to easily
move through a space without transference of germs or
leaving messy fingerprints behind. The highly sensitive
programming of the Wave-to-Open Switch picks-up hand
gestures within 100mm, ensuring it triggers operation only
when intended.
From bathrooms and entrances to all sorts of openings
throughout schools, universities, health care hubs, and
offices, these touch-less door opening solutions provide a
healthy means for meeting DDA requirements.
• Adjustable Hold Open
- Amount of time a door will stay in the full open
position after an activation
• Dynamic Braking
- Braking or slowing of the door if excessive door speed
occurs resulting from a wind load or an abusive open
condition
• Emergency Interface Relay*
- Door closes and ignores any activation input until
signal is discontinued
• Executive Mode Feature
- When door receives activation signal it opens and
remains open until either a second signal is received
or door is manually moved in closing direction
• Latch Assist
- At closed position, after an activation, the door is
pulled in
- After the door has closed, the door is pulled in to assist
with latch release/engagement
• Obstruction Detection
- Open - door closes if it hits an obstruction while opening
- Close (Stop on Stall) - door will stop once it hits an
obstruction and will rest against the obstruction until
obstruction is removed
• On/Off Switch
- Disables operator activation
• Open Delay*
- Delays operator opening for locking hardware
• Outside Push Button Disable*
- When contact is closed, outside push button is disabled
• Power Close
- Additional force to assist door closing between 90° and
70° and 10° and 0°
• Push & Go
- As the door is manually opened, the operator “senses”
movement and opens door to the full-open position
• Single Relay Output*
- Closes to indicate a valid activation
*Only available with Wireless Interface Module (WIM)

5831 Series Low Energy Operator
7
Lockwood Product Catalogue | 5831 Series Low Energy Operator
1300 LOCK UP (1300 562 587) lockweb.com.au
Swing Door Operators are suitable for varying building types
and applications and are used in environments to provide
automated access into a building or room. Whether to
achieve DDA Compliance or to effectively control pedestrian
traffic, they are designed to provide optimum convenience
for the user.
Swing Door Operators are available in two types depending
on energy requirements:
-Low Energy Operators
-Full Energy Operators
• Selection of the right operator will depend on a few
determining factors including, but not limited to:-
– Building Type
– Usage/Traffic
– Compliance to standards
The following can be used as a guide to help determine the
correct Swing Door Operator product to select.
If in any doubt, it is recommended to forward through the
enquiry to ASSA ABLOY Entrance Systems.
Low Energy vs Full Energy Operators
5831 Selection Guide
Doors equipped with low energy operators can be opened
manually or through the use of a actuation device (ie: push
button, wall switch, or hands free device).
In accordance with the DDA (Disability Discrimination Act),
low energy door operators can provide greater accessibility
for openings used by mobility-challenged individuals.
High energy door operators are designed to operate quickly
and continuously for optimal convenience. They are normally
activated via motion sensors when approached by pedestrians.
You will most often find them at entrances to supermarkets,
hospitals and shopping centres. They include provisions such
as safety sensors, to reduce the potential for personal injury
or entrapment.
HIGH ENERGY OPERATORLOW ENERGY OPERATOR

8Lockwood Product Catalogue | 5831 Series Low Energy Operator
1300 LOCK UP (1300 562 587) lockweb.com.au
5831 Series Low Energy Operator
Low Energy vs Full Energy Operators: Which is
right for my project?
Here are criteria to help you answer the question: Is my
project better suited to low or high energy door operators?
The 5831 Series is designed, built and tested in a state-of-the-art
facility in Monroe, North Carolina, USA. The information below is
designed to help you determine if a low energy operator is right for
your application.
They can be found in entrances to public buildings, including
schools, libraries, museums, offices and government buildings.
PROJECT
TYPE
Is this an entirely new project
or a retrofit project for which
you must use an existing door
system?
NEW New construction projects may specify high or low energy door
operators or a combination of both, depending on the intended use.
In retrofit projects, installing high energy operators is possible, though
costly, because it requires removal of the entire door frame for add
following: and a structural beam above the door for support.
Low energy operators can be installed on any existing door system.
RETROFIT
INTENDED
USE
Are openings required to
be accessible by mobility
challenged individuals? (Usage
expectations and relevant
compliance standards will
determine this.)
YES
Modern, low energy door operators enable smooth and quiet door
operation, much like an ordinary door. They can be used manually the
majority of the time and used automatically on occasion by mobility-
challenged individuals.
Low energy operators provide access to mobility-challenged
individuals without requiring them to push or pull open the door in
front of their path of travel.
NO
TRAFFIC
VOLUME
& FLOW
What is the expected traffic flow
and volume of usage?
HIGH
Low energy operators are often suitable for high and low traffic areas.
Some models are designed with a regenerative power system, which,
during manual operation, charges an onboard battery pack used
during automatic operation.
This feature eliminates the need to run electrical wire to the unit. High
energy operators are designed to operate quickly and continuously for
convenience (for example, in supermarkets and hospital emergency
rooms).
LOW
COST OF
OWNERSHIP
What is the overall cost of
ownership, including installation
cost, lifetime energy costs and
maintenance costs?
HIGH
High energy door operators are often packaged for sale with an annual
maintenance agreement to ensure the doors continue to operate
safely. In addition, installation costs for high energy operators have
been estimated to be twice that of low energy operators.
Some low energy operators have been designed to be installed and
serviced by existing facility maintenance staff, consume minimal
electrical power each year, and require no formal maintenance
agreements.
LOW
ACCESS
CONTROL
/ SECURITY
Is it necessary to control who
has access to particular areas?
In other words, is access control
required?
YES
When necessary, low energy operators can be integrated with electric
locking devices for complete access control.
NO

5831 Series Low Energy Operator
9
Lockwood Product Catalogue | 5831 Series Low Energy Operator
1300 LOCK UP (1300 562 587) lockweb.com.au
When determining which model door operator is best
suited for your project, it is also helpful to consider:
The expected design life of the project.
Is it a public school for which the design will remain fairly
constant over many decades and, therefore, requires a
heavy-duty opener?
Or is it a fast food restaurant that updates its décor every
few years, in which case, doors are replaced frequently to
support design changes.
Codes & Safety Requirements
LOW ENERGY OPERATORS HIGH ENERGY OPERATORS
Building
Standard
AS5007-2007
Powered Doors for Pedestrian Access and Egress.
(Has the ability to meet the requirement)
AS5007-2007
Powered Doors for Pedestrian Access and Egress.
Speed of
Operation
Must operate slowly and with minimal force upon
impact or resistance.
• Must take at least 5 seconds to fully open a door.
• Must hold door open for minimum of 5 seconds.
• Must take at least 5 seconds to close door.
These requirements increase as the weight and
size of the door increases.
Designed to operate quickly and continuously.
Safety Device
Requirement
Does not require safety devices. A properly adjusted
low energy door operator will stop, stall, or reverse
when an obstruction is encountered during operation.
AS5007-2007
Includes requirements for monitoring of
presence sensors and safety control mats.

10 Lockwood Product Catalogue | 5831 Series Low Energy Operator
1300 LOCK UP (1300 562 587) lockweb.com.au
5831 Series Low Energy Operator
Technical Information: wiring diagrams
Electric Strike with RF or Wired Push Buttons
and Card Reader (or other Access Control)
Wiring the WIM and Operator
LOCK
POWER
SUPPLY
INSIDE BUTTON
PRESS & RELEASE
TO LEARN
HOLD TO ERASE
OUTSIDE
BUTTON DOOR
OPERATOR
OPERATOR
SIGNALSIGNAL
DELAY
IF ER AP EN L NI OC OM TU
CA C SSE TC R
ON OC NM C
OL KC
OL KC
O
P EW R
UO ST DI BE TU OT N
ID AS LB E
POWER IN
12 OR 24V
OUTSIDE BUTTON
PRESS & RELEASE
TOLEARN
HOLD TOERASE
INSIDE
BUTTON
WIREL ESS RF
CONNEC TION
OPTIONAL
HAR D WIRED
CONNEC TION
OPTION AL
HARDWIRED
CONNEC TION
OUTSIDE
BU TTON
INSID E
BU TTON
FAIL SECURE
FAIL SAFE
CARD
READER
(ACCESS CONTROL)
ALARM
PANEL
System Description:
The Wireless Interface Module allows the 5831 Series
door operator to interface to 5800 wired or wireless
push buttons, wireless remote, an electric lock, fire panel,
access control, and an outside push button disable
contact.
Mounting:
The WIM (108mm x 146mm) is designed to fit inside a
power supply cabinet.
Inputs:
• Power input: 24VDC
• Hardwire push buttons input: separate INSIDE and an
OUTSIDE activation input
• Wireless push button input: separate INSIDE and an
OUTSIDE RF activation input
• Operator connection cable: Plug in 5831 Series swing door
cable connector interface
• Lock power: Dry contact SPDT to power an electric lock
• Outside push button disable: privacy feature
Outputs:
• Wireless Output: RF signal to activate door opener
• Output Contacts: SPDT dry contact output for AUX signal
• Lock Contacts: SPDT dry contact output for LOCK
• Access Control Contacts: indicates valid Unlock signal
• Signal Delay Timer: 1.5 second lock release delay
• Emergency Interface Relay (EIR): disables signal inputs
Wireless Interface Module (ADA1028W)