Assa Abloy Premium Plus HSA6410 User manual

Premium+ Alarm Kit
HSA6410
Installation · Programming · Operating
Keep this manual safe for reference and future maintenance
Introduction Contents
General System Overview
Thank you for choosing the Yale Wireless Alarm System.
This simple to install system has been designed with the
user in mind.
No connections
All the components are self contained and no connections
are needed between the panels. There is no need to
damage the home decor, lift carpets or run cables.
Number of devices
You can install up to 20 devices in the system. As well as
extra door/window contacts, PIR motion detectors and
smoke detectors, you can add keyfob remote controls and
keypads for added control convenience.
Long battery life
There is no need to wire into the mains supply or seek
the services of a qualified electrician. The control panel is
powered by a plug supply and all other components are
powered by battery (all batteries included).
Batteries operate for 2 years or more before they need
changing*. Regular testing and battery changes (when
notified by the system) will ensure reliability and peace of
mind. Please note that alkaline batteries must be used as
replacements. *Depending on usage.
Tamper proof system
The security accessories, control panel and external siren
are ‘tamper’ protected. Any unauthorised tampering with
these items will result in an alarm. This feature can be
turned off by the user when a battery change is required.
Take care of your safety
Display extreme caution when using ladders or steps,
please follow manufacturer’s instructions.
Be careful when using hand and power tools and follow
the manufacturer’s guidelines when using them. Take care
that the correct tools are used. Wear goggles or protective
clothing where required.
The external Siren is extremely loud, please ensure you
replace the cover and retreat to a safe distance before
testing.
Caution
The dialling facilities must only be used with persons who
have consented to being contacted by the system.
The system is not to be used to make 999 emergency
calls directly. Yale do not hold responsibility for any actions
taken by emergency services for incorrect use of the
dialling facility.
Information and illustrations are subject to change within this
document. Yale reserves the right to alter the specification and
product design at anytime without notice. Yale® is a registered
trademark. © 2017 ASSA ABLOY. All rights reserved.
Contents
1Location planning 2
2Unpack all the parts 4
3First Time Easy Install 6
4Mounting alarm devices 9
5Control Panel Menu System in Detail 12
6Using the System 18
Adding and using Accessories 20
Changing the batteries 22
Troubleshooting 24
Specifications 26
Recommended Installation Sequence
We recommend you follow the simple install
sequence, headings numbered 1-6.

2
Yale
R
!
pr
12abc
4ghi 5jkl 6mno
pqrs
78tuv wxyz 9
0
3def
Yale
R
!
pr
12abc
4ghi 5jkl 6mno
pqrs
78tuv wxyz 9
0
3def
Yale
Location planning
Home and Away Mode Planning
The home arming mode allows the premises to be
part armed so that no one can get inside without
warning the occupier, yet the person already inside
the house can move freely without triggering the
alarm. For example the downstairs of a house can
be armed while upstairs can be disarmed allowing
the user to go to bed without causing an alarm.
If this feature is to be used, then it should be
planned now, before installation.
Decide what areas can be occupied when in home
arming mode, the sensors for these areas should
be programmed to home omit; and the sensors
activated on the path to access the control panel
should be to be set to either Entry or Away Entry as
explained on page 15.
Operating Range
All devices must be within 30 metres of the control
panel and must not be mounted on or near large
metal objects. Avoid obvious sources of electrical
interference such as fridges and microwave ovens.
Tamper Switches
When mounting devices ensure that any tamper
switches close fully. On uneven surfaces it may be
necessary to place packing behind the switch for
reliable operation.
Extend The System
Extend the system in the future to increase your
security or as your needs change.
For example, add extra PIR motion detectors and
extra door/window contacts.
1Work out the best places to locate the devices for maximum protection. Having chosen the
locations do not mount at this stage.
Keypad remote control accessory
When used as second keypad, it is ideal in
bedrooms or at the top of a stairwell so the
ground floor can be armed when going to bed for
the night. Or, at a side or back door for alternative
entry.
• Mount at chest height for ease of use
• Designed for indoor use only
• Keypad should be accessible from a protected
entry/exit point
• Ensure that the keypad is not visible from the
outside of the premises.
PIR motion detector
• Mount in a position such that an intruder would
normally move across the PIRs field of view.
• Height should be between 1.7 and 2.3 metres
above floor level.
• Location in a corner will ensure wider room
coverage.
• Do not mount the PIR where its field of view will
be obstructed e.g. by curtains, ornaments etc.
• Do not point directly at sources of heat e.g. fires
or boilers, and do not position directly above
radiators.
• Avoid mounting the PIR directly facing a
window.
• Do not point the PIR at a door protected by a
door/window contact.
Panic button accessory
The panic button provides extra protection for
you and your family. When help is needed the
button can activate your alarm immediately - even
when the system is disarmed.
• Mount on bedroom wall or by the front door
• Not clearly visible to an intruder
• Easily accessible
• Out of reach of children

3
Yale
R
!
pr
12abc
4ghi 5jkl 6mno
pqrs
78tuv wxyz 9
0
3def
Yale
R
!
pr
12abc
4ghi 5jkl 6mno
pqrs
78tuv wxyz 9
0
3def
Yale
Keyfob remote control accessory
Can be used inside or outside the property and
can be kept on your keyring.
Smoke detector
• Mount in the middle of the ceiling at the top of
a stairwell, or on the centre of hallway ceilings
where smoke would most likely be detected.
• Do not mount in corners or above cooking
appliances and heaters.
• Install additional detectors if there are closed
doors preventing smoke from reaching
detectors. Door/Window contact
Select a door that will be the main point of entry
and exit, usually your front door.
• Mount as high as possible
• Do not aim a PIR motion detector at this door
or window
Yale
R
!
pr
12abc
4ghi 5jkl 6mno
pqrs
78tuv wxyz 9
0
3def
Yale
R
!
pr
12abc
4ghi 5jkl 6mno
pqrs
78tuv wxyz 9
0
3def
Yale
PIR motion detector
• Mount in a position such that an intruder would
normally move across the PIRs field of view.
• Height should be between 1.7 and 2.3 metres
above floor level.
• Location in a corner will ensure wider room
coverage.
• Do not mount the PIR where its field of view will
be obstructed e.g. by curtains, ornaments etc.
• Do not point directly at sources of heat e.g. fires
or boilers, and do not position directly above
radiators.
• Avoid mounting the PIR directly facing a
window.
• Do not point the PIR at a door protected by a
door/window contact.
Control panel
• Ensure the control panel is accessible when
entering through a protected entry/exit point.
• Avoid mounting the control panel where it would
be visible from the outside of the premises
• Locate by a mains socket and telephone point.
Siren
Choose a position on an external wall where the
siren would be most prominent. Mount as high as
possible, out of easy reach.

4
Unpack all the parts
2The easiest way to get to know the system and get it up and running quickly is to get all the
devices and accessories programmed on a table top before locating and mounting them.
WARNING
The siren is very loud, be prepared! Take care not to
activate the siren tamper switch unnecessarily.
1Remove the cover by unscrewing the single screw
located on the lid.
2Familiarise yourself with the internal components,
do not switch siren on at this stage, this will be
done at First Time Easy Install, section 3.
PIR movement detectors
1Pull out the plastic pull tab on the back of the PIR.
This will activate the batteries.
2A red light can be seen flashing through the
lens. This will last for 30 seconds indicating the
component’s initiation.
Text Display
Up
Down
Contactless
Reader
Programming
Menu
Arm Button
Part-Arm
Button
Disarm
Button
Microphone
Power LED
Add Device
Numeric &
Text Keypad
Back Space
OK
Fault LED
Control panel
A power adaptor is supplied that plugs into mains
supply wall socket and control panel. Do not plug
in at this stage, this will be done at First Time Easy
Install, section 3.
• In addition to the adapter, there is a rechargeable
battery inside the control panel that serves as a
backup in case of a power failure. A fully charged
battery can provide backup power for a period of
at least 10 hours. It takes approximately 36 hours
to fully charge the battery. The control panel is
equipped with a backlit LCD display and keypad
for easy operation in dark. To conserve backup
battery duration the backlights will be switched
off during mains power failure. The control panel
is also provided with a contactless tag reader that
allows the user to tap a tag to disarm the system.
Siren
The siren comes in two shapes, square shaped
and round depending on the kit purchased. The
operation and programming of the sirens are
identical, only the case is different.
Battery
Switch
Siren
Power Socket
Telephone
Socket

5
Door/window contacts
1Pull out the battery saver tab to activate the battery.
Cover screw
Learn/Test
Button
Status
LED
Battery
saver tab
Gap no more
than 8mm
Magnet
Sensor
Learn/Test
button
LED
Keyfob remote control accessory
1Open the battery compartment using a coin by
turning cover in the direction of the big arrow so
the cover small arrow is next to round dot.
2Insert battery and replace cover.
Smoke detector accessory
1Remove the cover and insert the four AAA
batteries as shown
2The Smoke detector will now enter into self-
calibration mode for 10 minutes. It will resume
normal operation after this period.
Panic button accessory
Remove the cover by loosening the fixing screw
and insert the 12V battery (supplied) as shown.
Please ensure you observe battery polarity.
Door/window contacts
1 Remove the cover of each door/window contact
by loosening the fixing screw.
2Insert two AAA batteries into each detector as
shown. The indicator LED will flash briefly.
7
Keypad remote control
Remove the cover and insert the 3 AAA alkaline
batteries as shown. The ‘Tx’ LED will flash briefly
while components initialise.
Please note, the Home button on the operating
panel and the jumper switch inside (do not move)
have no function on this model.
Smoke detector accessory
Remove the cover and insert the four AAA
batteries as shown.
Keyfob remote control accessory
Slide off the battery cover, insert the
23A/MN21 battery as shown, and replace
battery cover. Switch to ‘on’.
Help button accessory
Remove the cover by loosening the fixing
screw and insert the 12V battery (supplied) as
shown. Please ensure you observe battery
polarity.
Tamper
switch
Jumper
switch
Tamper
switch
Jumper
switch
Magnet
Extension terminals
Learn/Test button
Learn/Test
button
On/Off sw itch
Door/window contacts
1 Remove the cover of each door/window contact
by loosening the fixing screw.
2Insert two AAA batteries into each detector as
shown. The indicator LED will flash briefly.
7
Keypad remote control
Remove the cover and insert the 3 AAA alkaline
batteries as shown. The ‘Tx’ LED will flash briefly
while components initialise.
Please note, the Home button on the operating
panel and the jumper switch inside (do not move)
have no function on this model.
Smoke detector accessory
Remove the cover and insert the four AAA
batteries as shown.
Keyfob remote control accessory
Slide off the battery cover, insert the
23A/MN21 battery as shown, and replace
battery cover. Switch to ‘on’.
Help button accessory
Remove the cover by loosening the fixing
screw and insert the 12V battery (supplied) as
shown. Please ensure you observe battery
polarity.
Tamper
switch
Jumper
switch
Tamper
switch
Jumper
switch
Magnet
Extension terminals
Learn/Test button
Learn/Test
button
On/Off sw itch
Keypad remote control
1Pull out the plastic battery saver tab at the back of
the remote keypad. This will activate the batteries.
Battery
saver tab
ale
Y
R
123
6
5
4
789
0
A
B
Disarm
Home
Arm
Arm
LED
Yale
R

6
First Time Easy Install
• Any omissions or mistakes can be rectified
later. Once the first time install has been
successfully completed it will not be shown
again.
• More advanced programming can be done
at a later stage including adding and naming
sensors and changing various settings.
Unpack the kit
content on a
table. Remove the
mounting plate
(if fitted) from the
control panel. Move
rightwards to lock
and move leftwards
to release the panel
(panel top facing the
user). Connect the
power adaptor.
The control panel will beep and “Set user code (OK?)”
will be shown, and the green LED will be on.
Move rightwards to lock and move leftwards to release
the panel (panel top facing the user). Using a pointed
tool, slide the battery switch to the right in the direction of
the arrow to switch the internal battery.
The panel is now ready for the first time
installation steps:
3The quick install guide will prompt you to program the basic system in easy steps.
i
1. Set user code (OK?)
Press 3
2. Enter 1st code ….
Enter a four digit PIN code. Press 3
Xcan be use to correct wrong number.
Make a note of the entered code, it will be
required later.
3. Set 2nd code Y/N
Select No to skip, Yes to enter 2nd code.
Maximum 3 set of codes can be set.
The current selection is shown by the
flashing dot on the far LEFT. Use p/qkeys
to navigate.
4. Reset code / Next step
Select reset code to repeat step 2, or next
step to proceed.
Cursor is on NEXT STEP as default
5. Add Device (OK?)
Press 3
6. Push button on Device to Add
Keypad (Keys should be pressed positively within 3 secs of the
previous press)
1Press Panic button A and enter 0000
(The LED will now be flashing. System is now in setting mode)
2 Press Panic button A and enter 7
(The keypad will confirm with two fast flashes that it is in “Siren as master”
mode.)
3 Press Panic button A then 1to send learn-in signal, then
press disarm twice to quit.
ale
YR
123
6
5
4
789
0
Battery
cover
Coin
slot
Locked
Unlocked
Yale
PRESS
PRESS
PRESS
PRESS
PRESS
7. Detect (OK?)… Zone01 B
Press 3to confirm
Devices are labeled by the following codes:
·Door Contact DC
· PIR Sensor IR
· Smoke Sensor SD
· Remote Controller RC
· Remote Keypad KP
· Help Button FP (Fix-Panic)
8. More device / Next step
If you have more device to add to the system,
select More devices (this will go back to step
6), or select Next step to move forward.

7
10. Push learn button on siren (OK?)
• Press 3
• Press learn button on siren
11. Hear beep Y/N
Did you hear the siren beep when you press
the learn button on the siren? If not select No
and step 10 will be repeated.
12. Learn Siren Y/N
Select Yes to learn in siren. Select No to skip
learning siren
After selecting Yes, the siren should beep
13. Hear beep Y/N
Did the siren beep in the last step? If not
select No and go back to step 12
14. Add siren / Next step
You can add more siren or you can select to
move to the next step by using the p/qkey.
15. Set Tel. Number for alert (OK?)
Key in the full telephone number (number you
want to alert in the event of an alarm)
16. Set 2nd num? Y/N
Select yes if you want the system to call more
than one telephone number. Maximum 3
numbers can be stored.
17. Reset Number / Next step
Select reset Number to go back to step 15.
Select next step to move forward.
18. Rec Name&address 10 sec (OK?)
Press 3and follow on screen instruction to
record your message. Please say your name
and address slowly.
19. Record again / Next step
Select record again to go back to step 18.
Select next step to progress.
20. Test call?
You can choose to test the telephone message calling
feature with the Yes/No option. To make a test call plug in
the telephone line cord supplied into the control panel as
shown. Find a convenient telephone line wall socket and
plug the other end of the cord in. Follow the on-screen
instructions to complete the test.
• Check with the called party before doing the test.
• Four messages will be played:
·Address message you have just recorded
·Burglar message
·Emergency message
·Acknowledgement message
• The call can be terminated by the recipient pressing “9”
on the phone or by pressing the 5key on the panel.
• If the call is being made to a mobile or DECT radio phone,
press “9” repeatedly to cancel the call.
21. Call again / Next step
Select Call again to repeat test call.
22. Set Date/Time (OK?)
Press 3. Follow the on-screen instructions to
set both the time and date.
• The date and time is set by using the p/q
keys and then pressing 3when finished.
9. Add Siren (OK?)
• Remove the siren cover. Ensure
the siren power is switched off and set
the program switch number 1 to ON to
clear memory as shown.
• Press the siren learn button a few times
to drain any residual power.
• Switch on the siren power and wait for the siren
LEDs to flash and siren beep
• Then set the program switch number
1 to OFF, ready for learning in.
• Press 3NORMAL
155.30 33.18
155.31

8
23. Date/Time? / Next step
Select date/time? To go back to step 22.
Select next step to progress.
24. Start walk test (OK?)
Follow the on-screen instructions to test all the
learnt-in devices except the siren.
• Press the test buttons on the PIR and door contact
and the arm keys on the keyfob and keypad to
send a test signal.
• The walk test can be quit at any time by pressing
the Xkey.
• Walk test is used to check that the sensors are
working correctly. Walk test can also be used
to find out if the devices are in radio range of the
control panel.
• The control panel will chime and display the device
that sent the test signal.
25. Test device ? / Next step
To re-test press the pkey and 3, otherwise
press 3directly to go to the next step.
26. Setup finished (OK?)
Press 3and “Start again?” will be shown, to
restart press the pkey and 3, otherwise
press 3directly to go to finish.
• The control panel will display “Alarm off” with the
time and date.
• More advanced programming, such as adding
contactless tags, device naming, entry/exit times,
adding other users and any corrections can be
made in the main programming menu, see section
5 Control Panel Menu System in Detail.
• All the devices are set-up as burgular mode. This
will result in the siren ringing instantly when you
enter the house (no countdown). You need to setup
an entry device if you want a countdown period.
See Edit device on page 13.
Steps continued...

9
Mounting alarm devices
4WARNING To prevent the alarm from activating during installation, the siren must have its
tamper disabled and the control panel must be in ‘Walk Test’/Programme mode.
Control Panel Mounting
Table top
Remove the mounting back plate (if fitted) and
simply place on top of a table on its rubber feet.
•If the mounting plate has been fitted with the
power on, the control panel will show a panel
tamper condition when the plate is removed. To
cancel make sure that the mounting plate is not
fitted and power down by removing the power
plug and switching off the battery. Reconnect
power and switch the battery back on. The panel
tamper will be reset and not activate again unless
the plate is put back on.
Wall Mounting
Using the two holes on the mounting back plate,
mark the position of the holes. Drill two holes and
fix with the screws and plugs provided. Hook the
control panel onto the plate. Ensure that the control
panel is fitted at approximately chest height where
the display can be easily seen and the keypad
convenient to operate.
•The control panel tamper protection will
automatically arm when mounted on the back
plate.
Disabling the system tamper
1Press the key and enter a user PIN code
followed by 3.
2The control panel is now in programming mode,
Select Devices +/-, then Program Siren and
Siren Tamp. Off using the pq3 keys.
3Press 3 when in the Siren Tamp. Off menu
and the control panel will beep followed by an
acknowledgement pip from the siren.
• Siren programming is described more fully
in “Control Panel Menu System in Detail” in
section 5.
• The siren tamper will now be disabled for 1
hour after which it will automatically arm again.
If longer is needed to fit the siren then simply
repeat the steps above.
• Leave the control panel in programming
mode to stop the system responding to
tampers. If the control panel automatically
times out, re-enter programming mode
again.
Mounting the siren
Ensure the tamper switch is fully depressed when
the siren is mounted. If there is a gap, pack with a
suitable spacing material.
Round
Siren
Base
Wall
Spring Guide
Spring compressed
firmly against wall
Square Siren Base
Plunger must
be pressed in
fully against
wall
Wall
1 Find a location where the siren is to be mounted.
2 Using the large screws and wall plugs provided,
screw the siren onto the wall through the 4
mounting holes on the siren base.
3 Fix the siren cover with the securing screw.
4 Using the Programming Devices +/- menu enable
the siren tamper (see the end of this section “Final
step:”) and Arm and Disarm the system with the
control panel.
5 If there are 5 short beeps when armed, the tamper
switch is NOT fully depressed and will need to be
adjusted.
Unset the system and disable the siren tamper as
described above before adjusting the siren tamper
switch. If there is a gap between the wall and the
tamper switch mechanism, pack with a suitable
spacing material.
When adjusted repeat the steps above from steps
3 through 5.
6 If there is one short beep and flash when armed,
the siren is mounted correctly and the siren
installation is complete.
Before mounting it is important to disable the
siren and system tamper to avoid the siren
sounding an alarm.
i

10
Mounting other devices
Find a location where the device is to be mounted,
see section “Location Planning” for suggestions.
Mounting the Keypad:
Fixing Slots X 2
Keypad
Cradle Open
1 Drill holes into the wall using the fixing slots as a
template.
2 Fit wall plugs into the wall and fix cradle with the
screws provided.
3 Slide the keypad into the cradle
4 Close the cradle cover so the logo is facing you
Mounting the PIR motion detector
1 Open the PIR by loosening the bottom screw.
Knock out the relevant holes on the base where
the plastic is thinner. The center two knockout
holes are for flat wall mounting while the 4 side
holes are for corner mounting.
Corner fixing
knockouts X 4
Wall fixing
knockouts X 2
2 Drill holes into the wall using the knockout holes on
the base as a template.
3 Fit wall plugs and secure the PIR base with the
screws provided.
4 Fit the PIR back together and tighten bottom
screw, the PIR installation is complete.
Before proceeding to mount the devices
physically, check that the control panel will
receive the system radio transmissions by
doing a simple radio range test.
• Put the control panel into walk test mode.
•KEYPAD: press the arm button.
• HELP BUTTON: press the button.
• ALL OTHER DEVICES: Hold the device
in the desired location and press the
learn/test button, the control panel should
respond with a chime.
• When you are satisfied that the devices
work in your chosen locations, proceed
with the installation as described.
• If the control panel does not respond,
the location may be out of range, try
alternative locations until reliable radio
contact is obtained.
i
The PIRs have a built-in sleep timer to save
battery power. If there is no movement in front
of the PIRs for 1 minute, the PIRs will become
‘ready to signal’ and movement will now be
reported. The PIRs will sleep for 1 minute after
reporting.
Any movement detected in sleep time will not be
reported and will extend the sleep period by a
further 1 minute.
i