Atop MB5404D Series User manual

MB5404D Series
4-Port Modbus Gateway
Quick Start Guide
Version 1.0 August, 2011
This document is intended to provide customers with
brief descriptions about the product and assist
customers to get started. For detailed information and
operation of the product, please refer to the product
user’s manual in the product CD or Atop website.
1. PACKAGING
Check whether your package contains following items:
◎ MB5404D x1
◎ Quick Start Guide with Warranty Card x1
◎ Product CD x1
◎ 7-pin Screw Terminal Block (2ESDVM-07P) x1
Optional Accessories：
◎ Wall Mount Kit (WMK-B-459) 202EH731000003G
◎ Console Cable (CBL-RJ45(8P)-DB9(F)-90-C) 50891971G
◎ Grounding Cable (GDC-120) 59906861G
◎ Adaptor (ADP-DB9(F)-TB5) 59906231G
◎ Conductive DIN-Rail Kit (CDK-S-459) 201EH731000005G
◎ US315-12(US-Y) Power Adapter 50500151120009G
◎ USE315-12(EU-Y) Power Adapter 50500151120019G
◎ 7-pin Screw Terminal Block (2ESDPM-07P) 50707871G
◎ 7-pin Screw Terminal Block (2ESDVM-07P) 50707741G
2. HARDWARE DESCRIPTION
NOTE:
1. MB5404D (RS-232/422/485 DB9 without isolation ),
2. Press the Default button of MB5404D to reset to the default
value
Figure 2.1. MB5404D Series interfaces
LED Indicators:
Name Color Status Description
Off Power is not connected
Power Green On Power is connected
Off Ethernet Disconnected
Green Blinking Data is transmitting on
Ethernet for 100Mbps
LAN
Orange Blinking Data is transmitting on
Ethernet for 10Mbps
Off No data is transmitting on
COM port
COM Green Blinking Data is transmitting on
COM port
Off System is not ready or
halt
RUN Green Blinking AP firmware is running
normally
Installation Procedures:
Step 1: Connect MB5404D to power source
Step 2: Connect MB5404D to the Ethernet network. Use a
standard straight-through or cross-over Ethernet cable
Always make sure the PC is on the same network subnet
as MB5404D.
Step 3: Connect MB5404D’s serial port to a serial device.
Step 4: Mount MB5404D to a Din Rail.
3 SOFTWARE SETUP
DefaultNetworkSetting:
Default User Name/Password:
LAN1 IP: 10.0.50.100
User Name: admin
Gateway: 10.0.0.254
Password: null (leave it blank)
Subnet: 255.255.0.0
LAN2 IP：192.168.1.1
Gateway: 192.168.1.254
Subnet: 255.255.255.0

Auto IP (Dynamic IP): A DHCP server can automatically
assigns the IP address and all the network settings. MB5404D
supports the DHCP client function. By default, the DHCP client
function on MB5404D is disabled; you may activate the DHCP
client functions by executing Device View Utility ( Figure 3.1)
Figure 3.1. Device View Utility Dialog Window
Assign a Static IP address by:
1. Configuration by Telnet
i. Telnet to MB5404D using DOS command “Telnet
IP_address 23”. Example: telnet 10.0.50.100 23
ii. MB5404D’s network, link mode and COM ports settings
can be configured in the telnet window
2. Configuration by Device View Utility
i. Use Device View Utility on Product CD or our website
to configure MB5404D. First click ”Config” then assign a
static IP.
3. Configuration by Web Browser
i. Open a web browser, then Enter in the IP address as the
MB5404D. The default user name is admin and default
password is null (leave it blank).
ii. The MB5404D’s network, link mode and COM ports
settings can be configured on different web pages.
iii. Click “Save Configuration” to save settings.
Warranty Policy
Warranty Conditions
Products supplied by Atop Technologies are covered in this
warranty for sub-standard performance or defective
workmanship. The warranty is not, however, extended to goods
damaged in the following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock,
earthquake
(c) Use of unqualified power supply, connectors, or
maintenance procedure
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized "RMA" number
from Atop before shipping the goods to be repaired to Atop.
When in normal use, a sold product shall be replaced with a
new one within 3 months after purchase. The shipping cost
from the customer to Atop will be reimbursed by Atop.
After 3 months and still within the warranty period, it is up to
Atop whether to replace the unit with a new one; normally, as
long as a product is under warranty, all parts and labor are free
of charge to the customers.
After the warranty period, the customer shall cover the cost for
parts and labor.
Three months after purchase, the shipping cost from the
customer to Atop will not be reimbursed, but the shipping cost
from Atop to the customer will be paid by Atop.
Limited Liability
Atop shall not be held responsible for any consequential losses
from using Atop’s product.
Warranty Period
The Warranty Certification will not be effective until an authorized
stamp issued byAtop’s overseas agents.
Purchase Date: / / (yyyy/mm/dd)
Serial Number:
※ATOP Customer Services and Supports
1. Please contact your local dealers or Atop technical support
center at the following numbers.
y+886-3-550-8137 (Atop Taiwan)
y+86-21-6495-6232 (Atop China)
2. Please report the defected problems viaAtop’s Web site or
E-mail account
Web Site:www.atop.com.tw e-mail: [e-mail]
Web Site:www.atop.com.cn e-mail: [email protected]
Product Categories Warranty
Serial-to-Ethernet Server
Serial-to-WLAN Server
Industrial Wireless Ethernet Device
Modbus Gateway Series
Industrial Ethernet Switch
Embedded Serial Server
5 Years
DIN-Rail Power Supply 3 Years
Pick-to-Light System
Auto-Identification and Data
Collection-AIDC
Power Adaptor
Antenna
Other Accessories
1 Year