AVLink DVI-EXW User manual

DVI
EXTENDER
DVI-ELW
(Local)
DVI-ERW
(Remote)
USER MANUAL V1.1
DVI-EXW
Package Contents-
 1x DVI-ELW Local Unit
 1x DVI-ERW Remote Unit
 1 user manual
 2x Power adapter DC 12V with lock
 1x DVI 1.2M cable (DVI-D Male to Male)
 1x IR Blaster Cable(Peak Wavelength 940nm)
 1x IR Receiver Cable
 4x screws
 8x foot pads
Any thing missed, please contact with your vendor.
Features
 Through the DVI Extender, you can use one PC to
display identical image and extension of DVI signal up
to 100 meter on DVI monitor
 Supports resolution up 1920x1200
 HDCP Compliant
 Support RS-232(Bi-direction transfer)
 Supports all frequency band IR control
 One CAT.5 cable extension
 HD-baseT technology
 Use CAT.5 cable to install easily
Specifications
Function DVI-ELW DVI-ERW
DVI In Connector DVI Female x 1 None
DVI Out
Connector None DVI Female x 1
RJ-45 Connector 1
IR OUT 3.5ψ Stereo Jack x 1 None
IR2 IN None 3.5ψ Stereo Jack x 1
Max. Resolution Up to 1920x1200
Cable Distance 100 m (Max.)
Power Adapter
(Min.) DC 12V with lock
Housing Metal
Weight 313g 315g
Dimensions
(LxWxH) 150x80x35mm
-1-
LOCAL FRONT VIEW
1. IR OUT
2. HDCP LED
3. LINK LED
4. MODE LED
5. POWER LED
LOCAL REAR VIEW
1. Power jack (12V DC)
2. LINK (RJ-45 Connector)
3. DVI IN
4. RS-232
REMOTE FRONT VIEW
1. IR2 IN
2. IR1 IN
3. HDCP LED
4. LINK LED
5. MODE LED
6. POWER LED
REMOTE REAR VIEW
1. Power jack (12V DC)
2. LINK (RJ-45 Connector)
3. DVI OUT
4. RS-232
-2-

Installation
1. Turn off the PC and DVI monitor.
2. Connect the DVI extension cable between the PC and
the “DVI IN” port of DVI-ELW.
3. Connect the DVI extension cable between the DVI
monitor and the “DVI OUT” port of DVI-ERW.
4. Connect the CAT.5 cables between the DVI-ELW “LINK”
port and the DVI-ERW “LINK” port of extender.
5. Connect the power cord and turn on the extender.
6. Turn on the PC and DVI monitor.
IR Receiver Cable Directions:
Put it into the DVI-ERW “IR2 IN” port and place the IR
Receiver Cable, so that you can point to it easily with your
IR remote controller.
IR Blaster Cable Directions:
Plug IR blaster cable plug into DVI-ELW “IR OUT” port, it
sits in front of the device receiver’s IR sensor, which is
located on the front-panel.
Additional Options
Select any additional options you may require.
1. IR Receiver Cable
GND
+V
Sig
2. IR Blaster Cable
NC
P+
N-
-3-
Technical Specifications Output Signal
Pin #
Signal
Pin #
Signal
1 T.M.D.S Data 2- 16 Hot Plug Detect
2 T.M.D.S Data 2+ 17 T.M.D.S Data 0-
3 T.M.D.S Data 2/4 Shield 18 T.M.D.S Data 0+
4 T.M.D.S Data 4- 19 T.M.D.S Data 0/5 Shield
5 T.M.D.S Data 4+ 20 T.M.D.S Data 5-
6 DDC Clock 21 T.M.D.S Data 5+
7 DDC Data 22 T.M.D.S Clock Shield
8 Analog Vert. Sync 23 T.M.D.S Clock+
9 T.M.D.S Data 1- 24 T.M.D.S Clock-
10 T.M.D.S Data 1+
11 T.M.D.S Data 1/3 Shield C1 Analog Red
12 T.M.D.S Data 3- C2 Analog Green
13 T.M.D.S Data 3+ C3 Analog Blue
14 +5V Power C4 Analog Horz Sync
15 GND C5 Analog Ground
Wiring Information & Coding
Conductor
Identification
RJ45 Pin
Assignment
Color Code for
Conductor
Pair 1 5 White-Blue
4 Blue
Pair 2 1 White-Orange
2 Orange
Pair 3 3 White-Green
6 Green
Pair 4 7 White-Brown
8 Brown
-4-
-5-

Note
However sometimes, especially in demonstrations or in a
lab environment, the cable is rolled randomly in small turns
for convenience. The randomly rolled UTP cable suffers
additional signal impairments (compared to a straight cable)
and therefore the maximal operating reach might be
reduced.
Rolling a CAT5E cable around a 70cm fixed diameter
plastic drum has just a minor effect on the FEXT (Far End
Cross Talk) when compared to a fully stretched cable.
© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.
Trademarks:
All the companies, brand names, and product names
referred to this manual are the trademarks or registered
trademarks belonging to their respective companies.
-6-