B-K lighting ORION User manual

Hot SurfaceHigh VoltageWarning
Standard Installation
ORION
YOKE MOUNT
Flammable
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY
TO PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before
replacing lamp/LED. Fixture gets HOT quickly!
Contact only switch/plug when turning on.
Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time.
Use a soft cloth or gloves. Oil from skin may cause
damage.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
Waterproof Wire Connectors
Adjustable Crescent Wrench
Flat Head Screwdriver
TORX T27 Tamper Resistant 1/4” Bit
Mounting Hardware 3/4” Bolt w/ Lockwasher
Torque Wrench & 3/4” Socket
TOOLS
NEEDED:
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL
ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
RELEASE DATE
06/27/2023
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
REFERENCE NUMBER
INS-2506-00
ORION - YOKE MOUNT
Yoke
Optional: External Egg-Crate Louvers
(Not Field Removeable)
Cord with Built-in Watertight
Strain Relief
Heavy-Gauged, Die-Formed
Aluminum Housing
Tamper Resistant
Screws
LED Array

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASE DATE
06/27/2023
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
REFERENCE NUMBER
INS-2506-00
3. Adjust aim by slightly loosening two (2) 1/2-13”
bolts using an 3/4” socket. Aim fixture to desired
position and re-tighten bolts to secure in place.
Using torque wrench, tighten each bolt to 25
ft-lbs.
WIRING DIAGRAM
4. Fixture internal wiring (primary and secondary)
are factory pre-wired. Fixture is provided with 2ft.
leads for installer to make appropriate connections.
Make watertight connections using waterproof
wire connectors to connect primary wiring per
NEC. Be sure to leave enough cord length for
aiming the fixture.
HOT LED
NEUTRAL
GROUND
HOT
NEUTRAL
GROUND
Integral
DRIVER
+
-
0-10V -
0-10V +
0-10V -
0-10V +
2. Line up fixture yoke to mounting location and
secure with 3/4”-10 bolt (not included) and locking
washer. Using torque wrench, tighten to 30 ft-lbs
(mounting hardware not included).
1. Prepare for installation for yoke location. Clearance
hole is 7/8” diameter.
7/8” Dia.
120V Through 277V (MT)
Standard Installation
ORION
YOKE MOUNT