baby&child Chesterfield RH58KBK User manual

All Restoration Hardware bunk beds are designed to meet the highest safety
standards and comply with all U.S. and Canadian Bunk Bed regulations.
Assembly Instructions Bun
Model No: RH58KBK
Restoration Hardware Baby & Child
11640 Harre remove ektra 1 Street Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1005 West Georgia Street,
Vancouver, British Columbia V6E 4N7
WARNING: Read all instructions before assembling
this product. KEEPINSTRUCTIONSFORFUTUREUSE.
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You
can also order parts writing to the address above. Include the product model number,
color, and a brief description of the part. Call 1-800-762-1751
CARE AND CLEANINGCAGCARE AND CLEANING
DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft dry cloth add
period & Dab spills quickly with a soft cloth. Vacuum to remove dust.
If the Bunk Bed is to be stored, store in a cool dry place andcarefully package all original
hardware to protect from loss.
Page 1 of 12
!

IMPORTANT SAFETY INFORMATION FOR BUNK BED
1. Follow the information on the WARNINGS appearing on the upper bunk end structure and on the
carton. Do not remove warning label from bed
2. Always use the specified size mattress, to help prevent the likelihood of entrapment or falls
3. Surface of mattress must be at least 5 inches below the upper edge of guardrails on top bunk
4. Do not allow children under 6 years of age to use upper bunk.
5. Prohibit more than one person on upper bunk
6. Periodically check and ensure that the guardrails, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement parts.
10. Use of a night light may provide added safety precaution for a child using the upper bunk.
11. Use guardrails on both sides of the upper bunk.
12. I f t h e b u n k b e d w i l l b e p l a c e d n e x t t o a w a l l , t h e g u a r drail that runs the full length of the bed should be
placed against the wall to prevent entrapment between the bed and the wall.
13. The use of water flotation mattress is prohibited.
14. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that
not designed for use with the bed: for example, but not limited to,hooks, belts, and jump ropes
15. Keep these instructions for future reference.
Page 2 of 12
WARNING:
To help prevent serious or fatal
injuresfromentrapmentof falls;
●Never allow achild under 6years
onupper bunk.
●Use onlymattress which in 74"-75"
l o n g a n d 3 7 1 / 2 " - 3 8 1 / 2 " wi d e o n
u p p e r b u n k .
●Ensure thickness of mattress and
foundation combineddoes not exceed
7 " a n d m a t t r e s s i s a t l e a s t 5 " b e l o w
u p p e r e d g e o f g u a r d r a i l s .
●Use guardrails on both sides of upper
b u n k .
●Prohibit horseplay on or underbed(s).
●Prohibit more than one person onupper
b u n k .
●Use ladderfor enteringand leaving upper
b u n k .
STRANGULATION HAZARD - Never
attachor hang items to any part ofthe bunk
bed that are not designed for use with the
bed;for example, but not limitedto, hooks,
belts,and jump ropes.
D O N O T R E M O V E T H I S L A B E L
!

PARTSINCLUDE
Page 3 of 12
4 pcs

HARDWARELIST
HARDWARELIST
TOOLS NEEDED:
Screwdriver Phillips (Not included)
ASSEMBLY INSTRUCTION
Note:
-Bed must be assembled by at least two people.
-Please read instructions carefully before assembling bed.
-Use the above parts and fittings list to identify each component.
-Keep all packing materials until assembly is complete to avoid loss of smaller parts.
-Do not completely tighten all bolts until all steps are finished.
Page 4 of 12

Process:
Step 1:
Page 5 of 12
Insert the Allen Head Bolt (N) into the holes on the Left Bunk End (1) and Right Bunk End (2)
Standard the Left Bunk End (1) and Right Bunk End (2) upright and attached Bottom Side Rail (3).
1 2
3
4
4
3

Page 6 of 12
Step2:Attach Top Side Rail (4) to Left Bunk End (1) and Right Bunk End (2). Insert the Threaded Rods (A)
into the holes on the end of Top Side Rail (4), and insert Curved Washers (B), Spring Washers (C),
and Nuts (D) onto the Threaded Rods (A) to attach theLeft Bunk end (1) and Right Bunk End (2).
Tighten the Nut (D) and Threaded Rod (A) with Spanner Wrench (E). Repeat the procedure with Back
Side Rails (3).
1 2
3
3
4
4
A
B
C
D
E

Page 7 of 12
Step3: Attach Back Guard Rail (5) to Left Bunk End (1) and Right Bunk
End (2), by using the Allen Key (I) to tighten Allen Head Bolts (J)
andBigFlatWashers(K);
Step4:Attach Front Guard Rail (6) with Allen Head Bolts (J) and Big Flat Washers (K).
ForBunkswithLadderonLeftside,attach Front Guard Rail (6) to the Right Bunk
End(2),soladdersitsonLeft.
ForBunkswithLadderonRightside,attach Front Guard Rail (6) to Left Bunk
End(2),soladdersitsonRight.
Step 5:Reinforce the Back Guard Rail (5) and Front Guard Rail (6) with
MetalPlates(H),bytightening with Medium Screws (G);
BackGuardRail(5)
FrontGuardRail(6)
I
J
K
1
2
3
G
1 2
3

I
Page 8 of 12
Step6: Attached the Storage (10) to the Left Bunk End (1) and Right Bunk End (2) by using Allen Key (I)
to tighten Allen Headbolts(0).

Page 9 of 12
Step7:
-
-The webbing on the slats should be on the bottom side.
-Numbers on the slat roll show the locations to tighten the Big Screws
9
F
F
Lay the Slat Roll (9) in between the Top Side Rail(4) &Bottom Side Rail(3), then tighten with Big Screw (F).
9

Page 10of 12
Step8:Lay the Twin Panels (8) on top of the Slat Roll (9), and tighten with Medium Screws (G)
- Numbers on the panel show the locations to tighten the Medium Screws.
8
G

Page 11 of 12
Step9: Attach Ladder (7) to Front Side Rail (4) and tighten with Small S crews (L) and Small Flat Washers (M).
7
L
M

BEDDING SPECIFICATION:
The following size mattress and Foundation are specified for use with this Bunk bed;
MATTRESS:53-1/2”W×74” to 75”L×Maximum 7”H
PLATFORM PANEL:CONSISTING OF 4 PANELS(74.8”W×26.6”L×0.7”H)
Note: MATTRESS AND PLATFORM PANEL MUST NOT EXCEED 9” TOTAL THICKNESS Be sure to
adhere to these BEDDING SPECIFICATIONS in order to avoid the possibility of failing or entrapment.
THES SPECIFICATIONS MUST BE STRICTLY ADHERED TO!
FULL BUNK MATTRESS DIAGRAM
5”MINIMUM DISTANCE
FROM TOP OF MATTRESS
TO TOP OF GUARD RAJL
9”MAXIMUM
THICKNESS MATTRESS
PLATFORM PANEL
Thank you for your purchase
www.rhbabyandchild.com
Page 12 of 12
Step1: Install Bedding:Step1 :
0