baby&child Cabin Twin Loft Bed 355-81 User manual

All Restoration Hardware
bunk beds are designed to
meet the highest safety
standards and comply with
all U.S. and CanadianBunk
Bed regulations.
Page 1 of 10
RESTOTION HARDWARE
baby&child

Distributed in the U.S.A by:
Restoration Hardware
11640 Harrel St, Suite B Mira Loma
CA 91752
rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada Inc.
1500-1055 West Georgia Street,
Vancouver, British Columbia V6E
4N7
WARNING:
Read all Instructions before
assembling this product KEEP
INSTRUCTIONS FOR FUTURE
USE.
CUSTOMER SERVICE.
If you are missing parts or have any questions about this product, contact us first. You can also order
parts by writing to the address above. Include the product model number, color, and abrief descrip-
tionof thepart.Call 1-800-762-1751.
CAREAND CLEANING
DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft dry cloth. Rinse and dry
thoroughly. If the Bunk bed is to be stored, store in a cool dry place and carefully package all origi-
nal hardware to protect from loss.
Page 2 of 10
Restoration Hardware Baby & Child
11640 Harrel St, Suite B Mira Loma CA 91752
rhbabyandchild.com
Made in Vietnam
Assembly Instructions Cabin Twin &Full LoftBed
ModelNo:
#355-81 Cabin Twin Loft Bed
#355-82 Cabin Full Loft Bed
R ESTOTION HARDWARE
baby&child

IMPORTANT SAFETY INFORMATION FOR BUNKBED:
1. Follow the information on the WARNINGS appearing on the upper bunk end structure and on the
carton. DO NOT REMOVE WARNINGLABEL FROMBED.
2. Always use the specified size mattress or mattress support, or both to help prevent the likelihood
of entrapment or falls.
3. Surface of mattress must be at least 5inches below the upper edgeof side rails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the side rails, ladder, and other components are in their
proper position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use theladder for entering and leaving the upper bunk.
9. Do not usesubstitute parts. Contact Restoration Hardware for replacement parts
10. Use of anight light may provideadded safety precaution for a child using the upper bunk.
11. The use of water flotationmattresses is prohibited.
12. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are
not designed for use with the bed: for example, but not limited to, hooks, belts, and jump ropes.
13. Keep these instructions for future reference.
Page 3 of 10
CABIN TWIN & FULL LOFTBED

Parts Identification
Please note, Headboard and Footboard are interchangeable and can be installed on either end of bunk.
Page 4 of 10
(A) Bed Front (x1 piece)
(C) Ladder (x1 piece) (D) Bottom Side Rails (x2 pieces)
(F) Platform Panels (x2 pieces)
(H) Long Stretcher Bar (x1 piece)
(E) Top Side Rails (x2 pieces)
(G) Roof (x2 pieces)
(I) Short Stretcher Bar (x4 pieces)
(B) Bed Back (x1 piece)
CABIN TWIN & FULL LOFT BED

STEP 1:
While holding the Bed Front (A) & Bed Back (B)
upright, place the hooks of theBottom Side Rails
(D) into the slots in the post of theBed Front (A).
If necessary, using a thick magazine orbook to
protect the Bottom Side Rails (D), hammer with a
mallet orhammer until tight. Then hook the
Bottom Side Rails (D) into the Bed Back (B), (refer
to Detail "AA").
ASSEMBLY INSTRUCTIONS:
Note:
- Bed must be assembled by at least two
people.
- Please read instructions carefully before
assebling bed.
- Use the above parts and fittings list to
identify each component.
- Keep all packing materials until assembly
is complete to avoid loss of smaller parts.
- Do not completely tighten all bolts until
all steps are finished.
HARDWARE INCLUDED:
Page 5 of 10
Phillips Head Screwdriver
(Not included)
TOOLSNEEDED:
CABIN TWIN & FULL LOFTBED
1
2
3
4
5
5/16”x1-1/2” Short Bolt
5/16” Spring Washer
2 pcs.
8 pcs.
2 pcs.
10 pcs.
10 pcs.
48 pcs.
1 pc.
4mm Allen Key
30mm Long Screw
19mm Short Screw
5/16”x2-1/2” Long Bolt
5/16” Flat Washer
NO. ITEMDESCRIPTION
QTY.
6
7

STEP 3:
Position the Ladder (C) in the opening in the Bed Front (A). Hook the Ladder (C) over the rails of
Bed Front (A) and tighten with Short Screws (7) using Phillips head screwdriver (refer to Detail
"CC").
STEP 2:
Install the Top Side Rails (E) securely into the metal brackets on the Posts of Bed Front (A) & Bed
Back (B), (refer to Detail "BB").
Page 6 of 10
CABIN TWIN & FULL LOFT BED

STEP 4:
Lay the 4 Short Stretcher Bars (I) in between the Bed Front (A) and Bed Back (B), then tighten using
Long Screws (5) and Phillips head screwdriver (refer to Detail "DD").
STEP 5:
Lay the Platform Panels (F) on top of
the Short Stretcher Bars (I) and attach
using Qty.40 Long Screws (5) with
Phillips head screwdriver (not included),
(refer to Detail "EE").
Page 7 of 10
CABIN TWIN & FULL LOFT BED

STEP 7:
Set the Roof (G) on top of assembled bed frame.
STEP 6:
Attach the Long Stretcher Bar (H) onto the top of Top Side Rails (E) by using Long Bolt (1), Spring
Washer (3), Flat Washer (4) and Allen Key (6) to tighten.
Page 8 of 10
CABIN TWIN & FULL LOFT BED

STEP 9:
Place the Trundle ( optional, sold separately),
underneath the loft bed.
STEP 8:
Attach Roof (G) to the Top Side Rail (E) by using Short Bolt (2), Spring Washer (3), Flat Washer (4)
and Allen Key (6) to tighten.
Page 9 of 10
CABIN TWIN & FULL LOFT BED

STEP 10: INSTALL BEDDING
BEDDING SPECIFICATIONS FOR TOP BUNK:
The following size mattress and Foundation are specified for use with this Bunk bed.
MATTRESS DIMENSION SPECIFICATIONS FOR TOP BUNK:
Twin - over - twin Bunk: (74" - 75") long x (37 1/2" - 38 1/2") wide x 9" thick.
Full - over - full bunk: (74" - 75") long x (53 1/2" - 54 1/2") wide x 9" thick.
PLATFORM:
-Twin - over - twin bunk: Upper bed consists of 2 pcs platform 37 3/4" long x 38 3/4" wide x 3/4" thick.
-Full - over - full Bunk: Upper bed consists of 2 pcs platform 37 3/4" long x 53 7/8" wide x 3/4" thick.
**Note: MATTRESS THICKNESS MUST NOT EXCEED MAX 9" FOR TOP BUNK.
Be sure to adhere to these BEDDING SPECIFICATIONS in order to avoid the possibility of falling or
entrapment. THESE SPECIFICATIONS MUST BE STRICTLY ADHERED TO !
Page 10 of 10
CABIN TWIN & FULL LOFT BED