Barco MDSC-8358 RL User manual

MDSC-8358
User Guide
MDSC-8358RL-MDSC-8358RLG
MDSC-8358 RLF - MDSC-8358 RLH
(451920612552) K5902150/01
28/11/2017

Barco NV
Beneluxpark 21, 8500 Kortrijk, Belgium
Phone: [phone]
Fax: [phone]
Support: www.barco.com/en/support
Visit us at the web: www.barco.com
Registered address: Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
Phone: [phone]
Fax: [phone]
Support: www.barco.com/en/support
Visit us at the web: www.barco.com
PrintedinBelgium

Table of contents
TABLE OF CONTENTS
1. Welcome! .......................................................................................... 3
1.1 About the product ............................................................................................. 3
1.2 What’s in the box.............................................................................................. 3
1.3 About this user guide ......................................................................................... 4
2. Parts, controls and connectors ............................................................... 5
2.1 Front view...................................................................................................... 5
2.2 Rear view ...................................................................................................... 6
2.3 Connector view................................................................................................ 6
2.4 Connector pin assignments.................................................................................. 7
2.4.1 DVI–D single link / dual link connector................................................................ 7
2.4.2 RS232 connector........................................................................................ 8
3. Display installation .............................................................................. 9
3.1 Hoist bracket installation ..................................................................................... 9
3.2 VESA mount installation......................................................................................11
3.3 Video input connection .......................................................................................12
3.4 Video output connection......................................................................................13
3.5 Power supply connection.....................................................................................13
4. Daily operation ................................................................................... 15
4.1 On/Off switching...............................................................................................15
4.2 Power led status ..............................................................................................15
4.3 Brightness adjustment........................................................................................16
4.4 OSD menu activation.........................................................................................16
4.5 OSD menu navigation ........................................................................................16
4.6 OSD menu unlocking.........................................................................................17
5. Advanced operation ............................................................................. 19
5.1 Product info....................................................................................................19
5.2 Status info .....................................................................................................19
5.3 Brightness info ................................................................................................19
5.4 Transfer function ..............................................................................................20
5.5 Color temperature settings...................................................................................20
5.6 Color gamma settings ........................................................................................20
5.7 Input channel selection.......................................................................................21
5.7.1 Input channel menu .....................................................................................21
5.7.2 Failover input ............................................................................................21
5.8 OSD setting menu ............................................................................................22
5.8.1 Time-out OSD............................................................................................22
5.8.2 OSD menu lock..........................................................................................22
5.9 Setup menu....................................................................................................23
6. Important information ........................................................................... 25
6.1 Safety information.............................................................................................25
6.2 Environmental information ...................................................................................28
6.3 Biological hazard and returns................................................................................30
6.4 Regulatory compliance information .........................................................................30
6.5 Cleaning and disinfection ....................................................................................31
6.6 Explanation of symbols.......................................................................................31
6.7 Legal disclaimer...............................................................................................34
6.8 Technical specifications ......................................................................................34
6.9 Open source license information............................................................................38
7. Appendix A ........................................................................................ 41
7.1 RS-232 protocol...............................................................................................41
(451920612552) K5902150 MDSC-8358 28/11/2017 1

Table of contents
2(451920612552) K5902150 MDSC-8358 28/11/2017

1. Welcome!
1. WELCOME!
1.1 About the product
Overview
The Barco Medical Grade MDSC-8358 series are color high resolution liquid crystal displays especially
designed for medical imaging applications.
The MDSC-8358 is a 58” Color Flat Panel Display, intended to replace typical multi-monitor arrays in med-
ical applications, whenever a large display is needed in addition to high resolution, while offering the same
good rendering in greyscale medical imaging thanks to the DICOM conformance. It has been designed
to meet the specific need of typical monitor set-up in examination rooms, where monochrome and color
pictures have to be displayed and freely positioned over the display, when processed by a suitable graphic
engine.
The MDSC-8358 shall provide 8 MP screen resolution, high luminance and accept digital inputs, according
to the DVI standard, with the native panel resolution of 3840 x 2160.
The MDSC-8358 can operate as a decoder or a Dual Link monitor.
Other important features like the very large viewing angle, the high brightness level, the backlight stabiliza-
tion, the grayscale correction and the compliance with the DICOM standards, will help the users avoiding
misinterpretation in medical diagnosis.
The MDSC-8358 is also suitable for viewing a large range of contents, as color temperature and color
gamma adjustments are provided. The display can also be controlled by remote, through a serial or Eth-
ernet communication link. The MDSC-8358 shall be supplied with VESA 400 mounting interfaces.
The MDSC-8358 is available in two versions:
• MDSC-8358RL: 2 power supplies, no glass, no DVI Splitter
• MDSC-8358RLG: 2 power supplies, with glass, no DVI Splitter
• MDSC-8358RLF: 2 power supplies, no glass, with DVI Splitter
• MDSC-8358RLH: 2 power supplies, with glass, with DVI Splitter
1.2 What’s in the box
Overview
Your MDSC-8358 display comes with:
• MDSC-8358 user guide
• Hoist bracket (2 pcs)
• Screws for the hoist bracket (8 pcs)
• O-rings for the screws of the hoist bracket (8pcs), to be used in the display with the protection glass
• Plastic cap (8pcs), to be used in the display without the protection glass
• Screws for the VESA mount (16pcs)
• O-rings for the screws of the VESA mount (16pcs)
• DVI dual link cables 1.8m (2 pcs)
• AC power cords (1 pcs EU & 1 pcs US)
(451920612552) K5902150 MDSC-8358 28/11/2017 3

1. Welcome!
Keep your original packaging. It is designed for this display and is the ideal protection
during transport.
The user guide is available in other languages on www.barco.com.
1.3 About this user guide
Overview
This manual provides support to the user during the installation, set up and utilization of the MDSC-8358
display. Depending on the specific version that has been purchased, some of the features and options
described in this document may not apply to the display in user’s hands.
4(451920612552) K5902150 MDSC-8358 28/11/2017

2. Parts, controls and connectors
2. PARTS, CONTROLS AND
CONNECTORS
2.1 Front view
Overview
1
2 3 4 5
Image 2-1
1. Power On/Off
2. Enter key
3. Down key
4. Up key
5. Esc key
A 5-key keypad is located on the bottom of the display.
(451920612552) K5902150 MDSC-8358 28/11/2017 5

2. Parts, controls and connectors
2.2 Rear view
Overview
2
1 1 1 1 1
Image 2-2
1. VESA mount screw holes
2. Connector location
2.3 Connector view
Connectors
1 2 3 4 59 6 10 7 6 9 7
610 8 9
7
6
9
7
7 7
Image 2-3
6(451920612552) K5902150 MDSC-8358 28/11/2017

2. Parts, controls and connectors
1. Additional protective earth pin
2. Input power connector
3. RS-232 connector
4. Switch (between RS-232 & Ethernet)
5. Ethernet connector for monitor remote control
6. DVI-D single link / dual link connector (*)
7. +5V out connector
8. DisplayPort connector
9. DVI splitter output connector
10. DVI splitter input connector
(*) 4 DVI connectors, numbered from 1 to 4 from right to left; all connectors must be installed when in SL
mode; DVIs 1 & 3 or 2 & 4 must be installed when in DL mode.
The 5V connections are available with the specific purpose to power an external DVI
extender.
No other uses of the +5V are allowed.
Every +5Vout connector is connected with the nearest jack, but every pair is indepen-
dent (500mA max).
If a DVI pair is disabled, then there is no power on the connector and the jack, connected
to the DVI connector.
2.4 Connector pin assignments
2.4.1 DVI–D single link / dual link connector
Overview
Image 2-4
Pin Function
1D2_Rx- (T.M.D.S.)
2D2_Rx+ (T.M.D.S.)
3GND (data 2 shield)
4D4_RX- (T.M.D.S.)
5D4_RX+ (T.M.D.S.)
6SCL (for DDC)
7SDA (for DDC)
8N.C.
9D1_Rx- (T.M.D.S.)
10 D1_Rx+ (T.M.D.S.)
11 GND (data 1 shield)
12 D3_RX- (T.M.D.S.)
(451920612552) K5902150 MDSC-8358 28/11/2017 7

2. Parts, controls and connectors
13 D3_RX+ (T.M.D.S)
14 +5V input (form the video source system)
15 GND
16 +5V Power for DVI extenders
17 D0_Rx- (T.M.D.S.)
18 D0_Rx+ (T.M.D.S.)
19 GND (data 0 shield)
20 D5_RX- (T.M.D.S.)
21 D5_RX+ (T.M.D.S.)
22 GND (clock shield)
23 CK_Rx+ (T.M.D.S.)
24 CK_Rx- (T.M.D.S.)
2.4.2 RS232 connector
Overview
Image 2-5
Pin Function
1 Not connected
2Rx (driven by host)
3Tx (driven by display)
4 Not connected
5Ground
6 Not connected
7Not connected
8 Not connected
9 Not connected
8(451920612552) K5902150 MDSC-8358 28/11/2017

3. Display installation
3. DISPLAY INSTALLATION
3.1 Hoist bracket installation
WARNING:Two brackets are provided in the accessory kit to be used for service per-
sonal only.
WARNING:The hoist brackets are intended to be used during the monitor’s installation
phase only.
To mount and use the hoist bracket to the display
1. Mount the brackets to the display using the screws provided in the accessory kit. Verify that the screwing
operation is well done using a torque value of 4N/m.
2. Move your display as shown on the picture below.
(451920612552) K5902150 MDSC-8358 28/11/2017 9

3. Display installation
3. After transportation, you can remove the brackets and the 8 mounting holes can be closed, either with
8 plastic caps (version without the protection glass) or using the same screws adding the respective
o-ring (version with the protection glass).
10 (451920612552) K5902150 MDSC-8358 28/11/2017

3. Display installation
3.2 VESA mount installation
Overview
The display supports mounting arm & stands according to the VESA 400 mm standard.
CAUTION:Use an arm that is in compliance with VESA requirements.
CAUTION:The monitor VESA interface has been designed for a safety factor 6 (to sup-
port 6 times the monitor weight). In the medical system, use an arm with suitable safety
factor (IEC60601-1).
CAUTION:The IP21 protection level (for version with protective glass) requires the all
the VESA mount holes (on the back side of the display) are closed by the 16 screws (M6)
and the 16 o-rings provided in the installation KIT
(451920612552) K5902150 MDSC-8358 28/11/2017 11

3. Display installation
CAUTION:The arm or stand is not provided. The product stability must be verified in
the specific usage (according to IEC 60601-1 Clause 9.4.2.2)
To mount the display to an arm stand
1. Attach the mounting arm or the stand firmly to the display using minimum 6 screws (M6) pointed out by
the red arrows in the image below. The screws can be inserted maximum 11 mm and minimum 8 mm.
Image 3-1
3.3 Video input connection
WARNING:When the display is assembled in the medical system, take care of the an-
chorage of all cables, to avoid unwanted detachment.
To connect the video inputs
1. Connect the available display(s) to the corresponding video input(s) using the appropriate video ca-
ble(s).
12 (451920612552) K5902150 MDSC-8358 28/11/2017

3. Display installation
1 1 1
3 3
12
Image 3-2
Overview possible inputs
1. DVI
2. DisplayPort
3. DVI splitter
3.4 Video output connection
WARNING:When the display is assembled in the medical system, take care of the an-
chorage of all cables, to avoid unwanted detachment.
To connect the video outputs
1. Connect the available display(s) to the corresponding video output(s) using the appropriate video ca-
ble(s).
Image 3-3
Overview possible outputs
1. DVI splitter
The DVI single link connection cables 0.5m included in the box can be used to connect
two outputs of the video splitter to two inputs of the monitor.
3.5 Power supply connection
To connect the power supply
1. Connect the power cord set into the AC power adapter
(451920612552) K5902150 MDSC-8358 28/11/2017 13

3. Display installation
2. Plug the power connector of the adapter into the power port of the display.
Image 3-4
3. For additional grounding, earth the display by connecting the protective earth pin to a grounded outlet
by means of a wire with a minimum AWG18 size (according to national requirements regarding the
maximum admitted cable length). Use the included M4 screw to attach the wire to the protective earth
pin.
14 (451920612552) K5902150 MDSC-8358 28/11/2017

4. Daily operation
4. DAILY OPERATION
4.1 On/Off switching
About power management:
The display has 2 keys:
• Mainpowerswitch(toswitchofallpowertothedisplay).
• Push button to enter/exit the Power Down Mode.
The display can go in three different statuses:
• On Line: The display is in this status when the video input is good and an image is displayed. In this
status all circuits are powered and the power consumption depends from the backlight level.
• Standby: The display is in this status when the video input is gone, the backlight goes off. All circuits
remain powered but the power consumption is low. This status needs to be enabled in the OSD menu
(see "Time-out OSD", page 22).
• Power Down: The display can be brought into power down mode by pushing the power on/off key.
When the monitor is in Power Down, all circuits are shut down, backlight is off and the power con-
sumption is low. Only the CPU remains active (to detect when the display needs to come out of this
mode by pushing the power on/off key).
To change the status of your display:
1. Activate the power through the switch located on the back side of the display.
2. While your display is off, press the Power On/Off key once for 3 seconds.
The display goes into On Line status. If no valid input is detected, the display will go into standby mode.
To switch on/off your display:
1. While your display is on, switch off the power with the main power switch.
Or,
while your display is off, switch on the power with the main power switch.
4.2 Power led status
About the power led status
The behavior of the power led shows the status of the unit:
• Led is GREEN: Correct video timing and calibration.
• Led is GREEN (blinking): Boot phase at switching on (approx 5 or 15 seconds if splash screen is
enabled).
• Led is ORANGE: Out of calibration.
• Led is ORANGE: (blinking): Incorrect video timing (at least one of four inputs)
•LedisRED:StandBy
• Led is RED (blinking): Diagnostic error (PWS, Panel Temperatures) In this case of warning please
contact the service assistance.
(451920612552) K5902150 MDSC-8358 28/11/2017 15

4. Daily operation
4.3 Brightness adjustment
To quickly adjust the brightness
1. While no OSD Menu is on the screen, press the Up/Down keys to adjust the brightness as desired. The
brightness will be displayed in a window in the upper-left corner.
by pressing the Up/Down keys simultaneously, the default brightness will be restored
(400 cd/m² in DICOM modes and 57% in COLOR modes).
brightness ranges from 40 cd/m² to 600 cd/m² in DICOM modes and from 5% (about 90
cd/m²) to 100% (about 700 cd/m²) in COLOR modes.
4.4 OSD menu activation
To activate the OSD menu
1. If not already done so, switch on the display.
2. Touch the Enter key.
As a result, the OSD main menu comes up. If no further actions are taken within the following 30
seconds, the OSD menu will disappear again.
The time-out of the OSD menu automatic close function can be adjusted or disabled in
the OSD menu (OSD Time-out).
The OSD menu position can be adjusted in the OSD menu (OSD Hor. Pos. and OSD Vert.
Pos.).
The OSD menu can be locked for access, see "OSD menu lock", page 22. To unlock the
OSD menu by entering the password, see "OSD menu unlocking", page 17.
4.5 OSD menu navigation
To navigate through the OSD menu
• Press the enter key to open the OSD menu.
• Use the up/down key to scroll to the desired menu page.
• When the desired Menu page is highlighted, press the enter key to select the top menu item that will
be highlighted.
• Use the up/down key to move to other Menu Items, then press the enter key to select it.
16 (451920612552) K5902150 MDSC-8358 28/11/2017

4. Daily operation
• If the selected menu item is controlled by a slider use the up/down keys to adjust the item value, then
press the enter key to confirm.
• If the selected menu item is a multiple choices menu use the up/down keys to select the desired option
then press the enter key to confirm.
• Press the exit key to exit from the Menu page.
4.6 OSD menu unlocking
About the OSD menu lock
The OSD menu can be locked for access, see "OSD menu lock", page 22. If the OSD menu lock is
enabled, entering the OSD menu will display a ’ Request for password’ window.
To unlock the OSD menu
1. If not already done so, switch on the display.
2. Touch the Enter key.
As a result, the dialog box as shown below comes up if the OSD menu is password protected, see
"OSD menu lock", page 22.
ENTER PASSWORD: _ _ _ _
3. Enter the password by using the four right keys of the keyboard, you can label the four keys as 1, 2, 3
and 4 (from left to right). So, if i.e. keycode is ’4444’, it means you have to press four time the Esc key.
1 2 3 4
If the inserted password is not correct, the following message appears on the screen.
WRONG PASSWORD!
The default password is 1-3-3-4.
(451920612552) K5902150 MDSC-8358 28/11/2017 17

4. Daily operation
18 (451920612552) K5902150 MDSC-8358 28/11/2017