Bartec 07-3323-3 Series User manual

Operating Instructions Switch Module Type 07-3323-3...
BARTEC GmbH Max-Eyth-Straße 16
D-97980 Bad Mer entheim
Tel.: [phone]
Fax: [phone]
[email protected]
www.bartec.de
Reservation Technical data subject to chan e without notice. Chan es, errors and
misprints may not be used as a basis for any claim for dama es.
1/4
Switch module with connection cable
Explosion protection Technical data
Ex protection t pe
II 2G Ex d IIC T6
0044
Certification
PTB 00 ATEX 1092 X
Ambient temperature
-40 °C to +60 °C
Stora e, transport: -55 °C to +70 °C
approved for Zone
1
Description
These switch modules are used everywhere
in Group IIc, Zone 1 hazardous areas
where
machine functions are to be activated by
pressin a button or actuatin a switch.
The switch module is equipped with self-
cleanin contacts featurin positive brea
k
operation.
Each actuatin element is fitted into a
mountin hole on a control console or panel.
The respective switch module is then fas-
tened without tools to the actuatin element
and secured with a fixin nut (see followin
pa es for assembly).
The easy installation of the actuatin ele-
ments in the control console or panel allows
conformance to a hi h IP de ree of protec-
tion.
Dimensions in mm
01-3323-7D0003-A.01-BARTECAdvertisin A ency-294000
Protection class
determined by actuatin element and
additional enclosure.
Switch module up to IP 67 in combination
with actuatin element
PTB 00 ATEX 3114 U.
Weight
approx. 160 (without connection cable)
Rated insulation voltage
400 V (standard version)
Rated operating voltage (Ue)
AC 230 V and 400V
DC 24 V and 110 V
Enclosure material / manufacturing process
Thermoplastic / injection mouldin
Contact material
A SnO
2
Contacts
all contacts are self-cleanin and have
positive break operation
1 NC contact and 1 NO contact or
2 NC contacts or
2 NO contacts or
1 NC contact or
1 NO contact
AC-12: 16 A, 400 V
AC-15: 10 A, 400 V
DC-13: 0,5 A, 110 V
DC-13: 1 A, 24 V
Conventional thermal current I
the
16 A / +40 °C, 11 A / +60 °C
Connection
inte rated connection cable,
ø 9.1 mm, 4 x 1.5 mm
2
or
ø 7.7 mm, 2 x 1.5 mm
2
ø 7.1 mm, 4 x
Mounting
locked, by bayonet lock
Service life
mechanical: > 10
5
switchin cycles

Operating Instructions Switch Module Type 07-3323-3...
BARTEC GmbH Max-Eyth-Straße 16
D-97980 Bad Mer entheim
Tel.: [phone]
Fax: [phone]
[email protected]
www.bartec.de
Reservation Technical data subject to chan e without notice. Chan es, errors and
misprints may not be used as a basis for any claim for dama es.
2/4
01-3323-7D0003-A.01-BARTECAdvertisin A ency-294000
Safet Instructions
The switch modu
le and its actuatin element
may be used only within the specified ambient
and operatin temperature ran e.
Utilisation in areas other than those specified or
the modification of the product by anyone other
than the manufacturer will exempt BARTEC
from liability for defects or any further liability.
Incorrect installation can cause malfunctionin
and the loss of explosion protection.
The switch module may be connected and
mounted only by qualified personnel who are
authorised and trained to assemble electri
c
components in hazardous (potentially explo-
sive) areas.
Always disconnect the switch module from
volta e before assembly or disassembly.
The enerally applicable statutory rules and
other bindin directives relatin to workplace
safety, accident preventio
n and environmental
protection must be adhered to.
The switch module may be used only if it is
clean and not dama ed in any way.
Marking
Particularly important points in these instruc-
tions are marked with a symbol:
DANGER
Non-observance leads to death
or serious
physical injury. The necessary safety measures
must be taken.
CAUTION
Warning of damage to property and financial
and penal disadvantages (e.g. loss of guaran-
tee rights, liability etc.).
ATTENTION
mportant instructions and information on
preventing disadvantageous behaviour.
NOTE
mportant instructions and information on
effective, economical and environmentally
compatible handling.
Standards conformed to
EN 60079-0:2006
EN 60079-1:2004
DIN EN 60068-2-27:1995, 30 , 18 ms
Assembl and Commissioning
NOTE
The assembly of the switch module and actu
a-
tor is described in the operating instructions for
the actuating elements.
Assembl /disassembl
ATTENTION
Only authorised and qualified personnel may
do any of the assembly, disassembly, install
a-
tion and commissioning work.
The minimum centre-to-centre spacing b
e-
tween two mounting holes must be observed.
Make sure the switch module to be fitted is
intact (no cracks and no damage to the cable).
Position the switch module’s bayonet lock at
the m
ounted actuatin element and turn the
closin latch to connect it securely to the act
u-
atin element.
Installation
The switchin module is to be installed as a
stationary unit and with protection a ainst the
risk of mechanical dama e.
The free end of the c
onnection cable must be
connected either in the safe area or in Groups I
and II hazardous areas with an appropriate
enclosure ensurin “Ex e” increased safety or
an enclosure that conforms to another a
p-
proved type of protection under EN 60079-
0
Section 1.
When installin in an enclosure with the "Ex e"
type of protection, the clearance and creepa e
distances as in EN 60079-7 Section 4.3, Se
c-
tion 4.4 and Table 1 must be complied with at
the conductor ends.
Only suitable tools may be used for installation
wor
k. It is not permissible to modify the module
in any way.
The cable is to be fixed in a way that prevents
mechanical strain (between the illuminated
button and connection cable and between the
junction box and the cable). The minimum
bendin radius of the
cable must be at least 29
mm.
ATTENTION
Avoid any capacitive influence from parallel
conductors as well as any additional adverse
heat effects on the cable.
Commissioning
Before commissionin check that:
• the device has been installed correctly
• the device is not dama ed
• the connection has been established
properly
Operation, Maintenance and
Fault Clearance
The operator of the switch module must keep it
in ood condition, operate it properly, monitor it
and clean it re ularly. The switch module,
actuator
, sealin s and cables must be checked
re ularly for cracks and dama e.
NOTE
Dirty modules/actuators can be cleaned with
compressed air.
The switch module is defective if the switchin
unit does not perform switchin functions any
lon er. Defective switc
h modules cannot be
repaired; they must be replaced.
Defective actuators can be removed and r
e-
placed by functionin actuators of the same
type.
Accessories, Spare Parts
See BARTEC catalo ue also.
Disposal
The components in the switch module contain
metal and plastic parts.
Therefore the statutory requirements for electr
i-
cal scrap must be observed (e. . disposal by
an approved disposal company).
Service address
BARTEC GmbH
Max-Eyth-Straße 16
D-97980 Bad Mer entheim
Tel.: [phone]
Fax: [phone]

Operating Instructions Switch Module Type 07-3323-3...
BARTEC GmbH Max-Eyth-Straße 16
D-97980 Bad Mer entheim
Tel.: [phone]
Fax: [phone]
[email protected]
www.bartec.de
Reservation Technical data subject to chan e without notice. Chan es, errors and
misprints may not be used as a basis for any claim for dama es.
3/4
Contact arrangements for switch modules
T pe 07-3323-31.. T pe 07-3323-32.. T pe 07-3323-34..
2 NC contacts
BK
GY BN
BU
2 NO contacts
BK
GY BN
BU
1 NC contact + 1 NO contact
BK
GY BN
BU
T pe 07-3323-37.. T pe 07-3323-38..
1 NC contact
BN
BU
1 NO contact
BN
BU
01-3323-7D0003-A.01-BARTECAdvertisin A ency-294000
Ke
BK = black core
BN = brown core
BU = blue core
GY = rey core

Operating Instructions Switch Module Type 07-3323-3...
BARTEC GmbH Max-Eyth-Straße 16
D-97980 Bad Mer entheim
Tel.: [phone]
Fax: [phone]
[email protected]
www.bartec.de
Reservation Technical data subject to chan e without notice. Chan es, errors and
misprints may not be used as a basis for any claim for dama es.
4/4