Bartec 17-A1Z0-0005 User manual

HART Add-On Module
Installation Instruction

Installation Instruction - Translation
HART Add-On Module
Typs 17-A1Z0-0005, B7-A2Z0-0033 and G7-A0Z0-0007
Version for:
Non hazardous areas
ATEX/IECExZone1 andZone2
UL Class I Division 1 and Division 2
Document No.: B1-A2Z0-7N0001 / 400570
Revision A - Status: 29. September 2016
Reservation:
Technical data subject to change without notice. Changes, errors and
misprints may not be used as a basis for any claim for damages.
Content Pages
English 1-12
BARTEC GmbH
Max-Eyth-Straße 16
97980 Bad Mergentheim
GERMANY
Phone: [phone]
Fax: [phone]
Contact:
Service-mobilecom[email protected]
Download: www.bartec.de

Installation Instruction
(Translation) HART Add-On Module Typs 17-A1Z0-0005 , B7-A2Z0-0033 and G7-A0Z0-0007
Technical data subjectto change .
Revison A - 09/2016
EN 1/12
Basic Information
Read carefully before putting the device into operation.
The Installation Instruction is a fixed part of the product. It must be kept in the direct
vicinity of the device and the installation, operating and service staff must have access
to it at all times.
More detailed instructions of use can be found at www.bartec.de as well as the current versions of
the datasheets, user manual, certificates and EU declaration conformity or may be requested directly
from BARTEC GmbH.
Knowledge of the safety and warning information and the strict compliance with it is essential for
safety installation and use. Injuries and material damage can be avoided by circumspect handling
and systematically following the instructions.
The BARTEC companyreserves the rightto carryout technical changes atany time.
Maintenance and Repairs The pertinent erection and operating provisions for electrical systems
must be observed! Repairs to explosion-protected devices may only be performed by authorised
personnel with original spare parts and according to the state of the art. The applicable provisions
must beobserved in thisrespect.
Inspections According to EN/IEC 60079-17 and EN/IEC 60079-19, the operator of electrical
systems in potentially explosive atmospheres is obliged to have these inspected by an electrician to
ensure correct condition.
Warranty If non-specified components are used, the explosion protection will no longer be
guaranteed. In the case of externally procured parts, it is not guaranteed that these have been
designed and manufactured inaccordance with theirload and requisite safety.
Disposal As professional electrical devices, our devices are intended exclusively for commercial
use, so-called B2B devices, in accordance with the WE
EE Directive. Observe the national waste
disposal regulations when disposing of the devices. All products purchased from us can be returned
to us byour customers fordisposal.The sender shallbear the costs ofpostage andpackaging.

Installation Instruction
(Translation) HART Add-On Module Typs 17-A1Z0-0005 , B7-A2Z0-0033 and G7-A0Z0-0007
Technical data subjectto change .
Revison A - 09/2016
EN 2/12
Safety Instructions The HART Add-On Module may only be operated in a clean, undamaged
condition and may only be deployed within the specified temperature class and the temperature
range indicated for it. Special Conditions for explosion protection must be observed. The
assembly/dismantling must be conducted by qualified personnel authorised and trained to install
electrical components in potentially explosive areas. The use in areas other than those specified or
alteration of the product releases BARTEC from liability for defects and further liability. Modifications
and changes to the module are not permitted. The generally applicable statutory regulations and
other binding guidelines on occupational health and safety, on accident prevention and on
environmental protection must be complied with.
Danger, Warning and Note Symbols Safety instructions and warnings are specially
highlighted in this installation instruction and marked bysymbols.
DANGER
The DANGER sign drawsattention to a direct threat which if not avoided will lead to deathor very
serious injuries.
WARNING
WARNING draws attention to a possible threat which if not avoided can lead to death or very
serious injuries.
CAUTION
CAUTION draws attention to a possible danger which if not avoided can lead to slight or minor
injuries.
ATTENTION
ATTENTION draws attention to a potentially damaging situation which if not avoided can cause
damage to theequipmentor toobjects in itsvicinity.
Important instructions and information on effective, economical & environmentally
compatible handling.

Installation Instruction
(Translation) HART Add-On Module Typs 17-A1Z0-0005 , B7-A2Z0-0033 and G7-A0Z0-0007
Technical data subjectto change .
Revison A - 09/2016
EN 3/12
Marking, test certificate, and standards
Note: Full information see "usermanual" tabletPC.
Type 17-A1Z0-0005 for tablet PC "Agile X IS"
ATEX Zone 1 II2G Ex ia [ia Ga] IIC T4 Gb EPS 15 ATEX 1 069 X
IECEx Zone 1 Ex ia [ia Ga] IIC T4 Gb IECEx EPS15.0065X
NEC (USA/Canada) Class I Div 1 Groups A, B, C, D T4 CSA 70045374
Type G7-A0Z0-0007 for tablet PC "Agile"
ATEX II (2)G [ia Ga] IIC EPS 15 ATEX 1 069 X
IECEx [Ex ia Ga] IIC IECEx EPS15.0065X
NEC [Ex ia Ga] II C CSA 70045374
Special conditions on the test certification EPS15 ATEX 1 069 X
for typs 17-A1Z0-0005 and G7-A0Z0-0007
-Maximum ambient temperature range: -20 °C to +50 °C.
-The HART addon modulesshallbe protected againststrong charge generating processes.
-It is allowed to connect the HART add on module to non certified HART circuits outside
hazardous areas. Um = 60 V shall never be exceeded. The user is responsible to meet this
condition.

Installation Instruction
(Translation) HART Add-On Module Typs 17-A1Z0-0005 , B7-A2Z0-0033 and G7-A0Z0-0007
Technical data subjectto change .
Revison A - 09/2016
EN 4/12
Type B7-A2Z0-0033 for tablet PC "Agile X"
ATEX Zone 2 and 22 II 3G Ex ic [ia Ga] IIC T4 Gc
II 3D Ex ic [ia Da] IIIB T135 °C Dc EPS 15 ATEX 1 823 X
IECEx Zone 2 and Zone 22 Ex ic [ia Ga] IIC T4 Gc
Ex ic [ia Da] IIIB T135 °C Dc IECEx EPS15.0010X
NEC (USA/Canada) Class I Division 2
Groups A, B, C and D UL File E321557
Special conditions on the test certification EPS 15 ATEX 1 823 X
for type B7-A2Z0-0033
-Maximum ambient temperature range:-20°C to +50°C.
-External connectors shall never be used in hazardous areas. The battery shall never be
removed, changed or charged in hazardous areas.The RFID module shall never be mounted or
removed in hazardous areas. The flash (LED) shall never be used as a permanent light in
hazardousareas.
-The apparatus shall be protected against mechanical impact, excessive UV-light and strong
charge generating processes.
-In combination with Bartec accessory 03-9849-0130 (hand strap) the device is only suited for
gas group IIA.
-It is allowed to connect the HART add on module to non certified HART circuits outside
hazardous areas. Um = 60 V shall never be exceeded. The user is responsible to meer this
condition.

Installation Instruction
(Translation) HART Add-On Module Typs 17-A1Z0-0005 , B7-A2Z0-0033 and G7-A0Z0-0007
Technical data subjectto change .
Revison A - 09/2016
EN 5/12
Device / system specification
HART interface UI ≤ DC 30 V
II ≤ 130 mA
PI≤ 1 W
U0≤DC 3 V
I0≤ 10 mA
P0≤ 5 mW
Um≤ DC 60 V
max. cable length:1.8 m
Size (weightx length xheight) 125 mm x 125 mm x 24 mm
Weight 200 g
Protection class(IEC 60529) Mounted on tabletPC: IP54
Connector strip (PoGo Pins): IP20
Operating temperature
insidehazardousareas
outside hazardous areas
-20 °C to +50 °C
-20 °C to +60 °C
Storage temperature -30 °C to +70 °C
Operating humidity 30 % to 95 % (non-condensing)

Installation Instruction
(Translation) HART Add-On Module Typs 17-A1Z0-0005 , B7-A2Z0-0033 and G7-A0Z0-0007
Technical data subjectto change .
Revison A - 09/2016
EN 6/12
Introduction
The intrinsically safe combination of the tablet PC system and the newly developed HART Add-On
Module makes it possible to perform diagnostics, set parameters and manage field devices much
more quickly and efficiently. The HART modem is used as an add-on module for the tablet PC
system in its extension interface. Since the user is now able to switch safely between the Ex and
non-Ex area, only one device is then needed for the wireless uploading or adjusting of the field
devices distributed there, completelyindependentlyof the controlsystem.
Scope of delivery:
-1x HARTAdd-On Module
-2x Pan head screw M3x10
-2x Pan head screw M3x7
-2x Truss head screw M3x7
-2x Connection cable
-2x Test probes
-1x Installation instructionHARTAdd-On Module
DANGER
The extension interface of the tablet PC must always be sealed in a potentially explosive
atmosphere! There is a risk of explosion!
 Only remove or mount the cover of the extension module outside the potentially explosive
atmosphere.
Only assemble/dismantle the HART Add-On Module outside the
potentially explosive
atmosphere.
Riskof short circuiting if the screws suppliedwith delivery are not used.
 Carry out the correct assembly for the attachment.
Use the screws supplied with delivery. All screws must be used to ensure the safe
mechanical assembly of the HARTAdd-On Module on the tablet PC.
Store the cover ofthe extension port safely.

Installation Instruction
(Translation) HART Add-On Module Typs 17-A1Z0-0005 , B7-A2Z0-0033 and G7-A0Z0-0007
Technical data subjectto change .
Revison A - 09/2016
EN 7/12
Installation HART Add-On Module
Only assemble/dismantle the HART
Add-On Module outside the potentially
explosive atmosphere.
Only use the HART Add-On Module for
the purpose that they have been tested
and certificatedby BARTEC..
Avoiddata losses!
Donot just switch the tablet PC
using the "ON/OFF" switch.
1. Shut the tablet PC down using the
operating system.
2. Place the tablet PC on the display
side, taking care that no parts
nearbyscratch the screen.
3. Remove the coveron the extension
interface.
4. Remove the top two screws on the
I/O interface cover.
5. Unpack the HART Module (the
srews supplied for mounting are in
the packaging).
6. Place the HART Add-On Module
on the extension interface.

Installation Instruction
(Translation) HART Add-On Module Typs 17-A1Z0-0005 , B7-A2Z0-0033 and G7-A0Z0-0007
Technical data subjectto change .
Revison A - 09/2016
EN 8/12
7. Fasten the HART Add-On Module
using the six screws supplied.
Torque 3Nm.
8. Visual inspection of the HART
Add-On Modules to ensure correct
positioning andassembly.
9. Switch the tablet PC on using the
"ON/OFF" button.
Optional: Attach hand strap.
(MaterialNo. 03-9849-0130)
10. Losen the top screw thatholdsthe
HARTAdd-On Module in place.
11.
Place the hand strap on and
fasten using the four M3x8
(supplied) pan head screws.
Torque: 3 Nm.
Do not assemble or remove the
hand strap in a potentially
explosive atmosphere.
DANGER
Zone 2: Tablet PC Agile X
There is a risk of fatal injury in an
explosive atmosphere!
The hand straps may onlybe
used in areaswithgas group
IIA.

Installation Instruction
(Translation) HART Add-On Module Typs 17-A1Z0-0005 , B7-A2Z0-0033 and G7-A0Z0-0007
Technical data subjectto change .
Revison A - 09/2016
EN 9/12
Setting up/activating the HART Add-On Module
Switching the tablet PC on.
Press the ON/OFF button for three
seconds.
Activating the HARTAdd-On
Module.
(1) Click on "Hottab" on the start
screen to start theapplication.
(2) Click in the menu on the option
"Device ON/OFF".
(3) Select "Ext.Module" to active the
extension interface.
(orange = ON; White = OFF)
(4) Power set to ON.
In up-to-date versions of the operating
system the driver has already been
integrated in the image. With older
versions the driver must be installed
manually using the device manager.
Affects "Hottab" versions from
1.40 and higher. Older versions
can be updated..

Installation Instruction
(Translation) HART Add-On Module Typs 17-A1Z0-0005 , B7-A2Z0-0033 and G7-A0Z0-0007
Technical data subjectto change .
Revison A - 09/2016
EN 10/12
Downloading and installing driver software
1. If the driver for the virtual COM port
is not listed in the tablet PC’s
system image, a new "CP2109 USB
to UART Bridge Controller" device
will appear under "Other devices"
in the device manager once the
HART Add-On Module has been
mounted.
2. Download the driver from:
http://automation.bartec.de/
3. Unzip the zip file.
4. Select the right driver installer for
the operating system
- 32-bit driver version:
CP210xVCPInstaller_x86-Installer
- 64-bit driver version:
CP210xVCPInstaller_x64-Installer

Installation Instruction
(Translation) HART Add-On Module Typs 17-A1Z0-0005 , B7-A2Z0-0033 and G7-A0Z0-0007
Technical data subjectto change .
Revison A - 09/2016
EN 11/12
5. The "User Account Control"
(UAC) window opens.
6.
Start installation by clicking on
"Yes".
7. Continue installation in the
"CP210x USB to UART Bridge
Driver Installer
" window by
clicking on "Next".
8. Accept the licence conditions by
clicking on "
I accept this
agreement"
and confirm by
clicking on "Next".

Installation Instruction
(Translation) HART Add-On Module Typs 17-A1Z0-0005 , B7-A2Z0-0033 and G7-A0Z0-0007
Technical data subjectto change .
Revison A - 09/2016
EN 12/12
9. The "The
Drivers were
successfully installed on this
computer" message
appears in
the window.
Complete installation by clicking on
"Finish".
10. Once the driver has been installed,
the HART Add-On Module can be
found in thedevice manager under:
"Ports (COM & LPT)" with the
designation "Silicon Labs CP210x
USB to UART Bridge".

EN_B1-A2Z0-7N0001-09/2016-Automation-400570
Your partner
for safety
technology.
Challenge us!
BARTEC GmbH
Germany
Phone: [phone]
Fax: [phone]
Max-Eyth-Str. 16
97980 Bad Mergentheim
[email protected]
www.bartec.de