Bartec 17-A1Z0-0005 User manual

Tablet PC Agile X IS
HART Add-on Module
Installation instruction

BARTEC GmbH
Max-Eyth-Straße 16
Fon: [phone]
Support:
em[email protected]
97980 Bad Mergentheim
Fax: [phone]
Download:
http://automation.bartec.de
GERMANY
Internet:
www.bartec.com
Installation instructions - Translation
HART Add-on Module
for Agile X IS –10.1” Tablet PC
Type 17-A1Z0-0005
ATEX/IECEx Zone 1
UL Class I Division 1
Document No.: B1-A2Z0-7N0001
Status: July 2021 / Revision B
Proviso: Subject to technical changes. Changes, mistakes, and printing errors do
not substantiate any claim to damages.
Content
Pages
English
1-15

HART Add-on module
Type 17-A1Z0-0005
Basic safety information
Subject to technical changes.
July 2021 / Revision B
1/15
1Basic safety information
1.1 Information on this Installation instruction
Read carefully before putting the devices into operation.
The Installation instruction is a fixed part of the product. It must be kept in the direct vicinity
of the device and the installation, operating, and service staff must have access to it at all
times.
The Installation instruction contains important information, safety instructions, and test
certificates which are necessary for the perfect function of the device in operation.
The Installation instruction is directed at all individuals concerned with the commissioning,
handling, and servicing of the product. The applicable guidelines and standards for areas
with gas and dust atmosphere (EN/IEC 60079-17, EN/IEC 60079-19) must be observed
when conducting this work.
Knowledge of the safety and warning information in this Installation instruction and the
strict compliance with it is essential for safe installation and commissioning. Accidents,
injuries, and material damage can be avoided by circumspect handling and systematically
following the instructions.
The examples, tables, and figures provided in this Installation instruction are for illustration
purposes. Due to the different requirements of the respective application, the BARTEC
company cannot assume responsibility or liability for actual use based on the examples
and figures.
The BARTEC company reserves the right to carry out technical changes at any time.
In no event will BARTEC company be responsible or liable for indirect or consequential
damages resulting from the use or application of this Installation instruction.
Safety and warning information is particularly emphasized in this Installation instruction and
marked by symbols.
DANGER
DANGER describes a directly imminent danger. If not avoided, death or severe injury
will be the consequence.
WARNING
WARNING describes a possibly imminent danger. If not avoided, death or severe injury
may be the consequence.
CAUTION
CAUTION describes a possibly imminent danger. If not avoided, mild or slight injury may
be the consequence.
ATTENTION
ATTENTION describes a possibly damaging situation. If not avoided, the plant or
objects in its vicinity may be damaged.
Important information on effective, economical & environmentally compliant handling.

Basic safety information
HART Add-on module
Type 17-A1Z0-0005
2/15
Subject to technical changes.
July 2021 / Revision B
1.1.1 Languages
The original Installation instruction is written in German. All other available languages are
translations of the original Installation instruction.
The Installation instruction is available in German and English. If further languages are
required, these must be requested from BARTEC or stated on placing an order.
1.1.2 Changes in the document
BARTEC reserves the right to change the content of this document without notification. No
warranty is assumed for the correctness of the information. In cases of doubt, the German
safety instructions apply because it is not possible to rule out errors of translation or printing.
In the case of legal disputes, the “General Terms and Conditions of Business” of the
BARTEC Group also apply.
The current versions of the datasheets, certificates, and EU declarations of conformity can
be downloaded from www.bartec.com or may be requested directly from BARTEC GmbH.
1.2 Handling the product
The product described in this Installation instruction left the factory in a perfect and tested
state in terms of safety. To maintain this state and to achieve a perfect and safe operation
of this product, it may only be operated in the manner described by the manufacturer. In
addition, the perfect and safe operation of this product requires correct transportation,
proper storage, and careful operation.
The safe and perfect handling of the HART Add-on Module is a prerequisite for its perfect
and correct functioning.

HART Add-on module
Type 17-A1Z0-0005
Basic safety information
Subject to technical changes.
July 2021 / Revision B
3/15
1.3 Safety information
Do not dry wipe or clean devices in potentially explosive atmospheres!
Do not open devices in potentially explosive atmospheres.
General statutory provisions or guidelines on occupational health and safety, accident
prevention provisions, and environmental protection laws must be heeded, e.g.
Operational Safety Ordinance (BetrSichV) and nationally applicable ordinances.
Use suitable clothing and shoes concerning the danger of hazardous electrostatic
charges.
Avoid heat influences outside the specified temperature range.
Protect the device from external influences! Do not expose the device to
caustic/aggressive liquids, vapors, or spray. In the case of malfunction or damaged
enclosure, remove the device immediately from the potentially explosive atmosphere
and bring it to a safe place.
1.4 Labeling, test certificate, and standards
Labels on explosion protection and the test certificate are attached to the HART Add-on
module. Labeling see chapter: Technical Data.
The guidelines and standards applicable to the HART Add-on module for devices and
protected systems for intended use in potentially explosive atmospheres see chapter: EU
Declaration of Conformity.
1.5 Co-applicable documents
All documents are available online from the following websites:
BARTEC: www.bartec.com or http://automation.bartec.de
Document BARTEC
Explanation
Quick Start Guide
Agile X IS
This Quick Start Guide describes the safety
information, initial use and other data about
the Tablet PC Agile X IS.
User Manual
Agile X IS
This User Manual describes the use,
commissioning, and settings of the Tablet
PC Agile X IS.

Product description
HART Add-on Module
Type 17-A1Z0-0005
4/15
Subject to technical changes.
July 2021 / Revision B
2Product description
2.1 HART Add-on module
The intrinsically safe combination of Tablet PC and HART Add-On Module makes it
possible to perform diagnostics, set parameters, and manage field devices much more
quickly and efficiently. The HART modem is used as an add-on module for the tablet PC
system in its extension interface. Since the user is now able to switch safely between the
Ex and non-Ex area, only one device is then needed for the wireless uploading or
adjusting of the field devices distributed there, completely independently of the control
system.

HART Add-on Module
Type 17-A1Z0-0005
Technical data
Subject to technical changes.
July 2021 / Revision B
5/15
3Technical data
3.1 Explosion protection
ATEX Zone 1
Type 17-A1Z0-0005
HART Add-on Module
Labeling
Ex II 2G Ex ia [ia Ga] IIC T4 Gb
Test certificate
EPS 15 ATEX 1 069 X
Standards
See chapter: EU Declaration of Conformity
IECEx Zone 1
Type 17-A1Z0-0005
HART Add-on Module
Labelling
Ex ia [ia Ga] IIC T4 Gb
Test certificate
IECEx EPS 15.0065X
Standards
See chapter: EU Declaration of Conformity
Class I, Division 1
Type 17-A1Z0-0005
HART Add-on Module
Labelling
Class I Div 1 Groups A, B, C, D T4
Test certificate USA and Canada
CSA 70045374
X - labeling (special conditions of use for secure operation within the potentially
explosive atmosphere)
The ambient temperature range is -20 °C ≤ Ta ≤ +50 °C.
The device must be protected from impact with high impact energy, from intense UV-
irradiation, and strongly charge generating processes.
It is allowed to connect the HART add-on module to non-certified HART circuits outside
hazardous areas. Um = 60 V shall never be exceeded. The user is responsible to meet
this condition.

Technical data
HART Add-on Module
Type 17-A1Z0-0005
6/15
Subject to technical changes.
July 2021 / Revision B
3.2 Features
HART interface
UI≤ DC 30 V
II≤ 130 mA
PI≤ 1 W
U0≤ DC 3 V
I0≤ 10 mA
P0≤ 5 mW
Um≤ DC 60 V
max. cable length: 1.8 m
Dimensions:
(Length x Width x Height)
125 x 125 x 24 mm
(4.92 x 4.92 x 0.94 inch)
Weight
approx. 200 g
(approx. 7.05 oz)
3.2.1 User environment
Operating temperature
-20 °C to +50 °C ( -4 °F to +122 °F)
Storage temperature
-30 °C to +70 °C (-22 °F to +158 °F)
Relative humidity
5 % to 95 % (non-condensing)
Class of protection (IEC 60529)
Mounted on Tablet PC: IP54
Connector strip (PoGo Pins): IP20