BDI CORRIDOR SV 7128 User manual

1
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to your BDI
products. Register today, and you will be entered to win free a BINK table
from BDI: www.bdiusa.com/register
Placement and Maintenance
Your Corridor Console is designed for indoor use on level floors. Clean
wood veneer and steel parts with a moist cloth.
Corridor is engineered for easy assembly. Carefully follow this procedure
to prevent any damage. Do not use power tools for assembly of
this product.
Step 1 Unpack and identify the parts listed below. The assembly
workspace should be a non-marring surface such as carpet. For missing
hardware pieces, contact BDI Customer Service at:
[email protected].
For all other concerns, please contact your BDI retailer.
Designed by Matthew Weatherly.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Corridor & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2017, BDI
Made in China. 10.05.2017 V1
CORRIDOR SV™7128
2 BAY CONSOLE
A1 Cabinet x 1
C5 Glass Top x 1
bdiusa.com
customerservic[email protected]om
T2 Hex Wrench x 1
H1 1/4-20 x 15 mm
Machine Screw x 8
H2 1/4-20 x 63 mm
Machine Screw x 6
T1 Phillips Screwdriver x 1
A2 Sub Frame x 1
A3 Leg Frame x 2
H3 M4 x 35 mm
Machine Screw x 4
H4 Rubber Bumper x 6
H5 Door Pull x 2

bdiusa.com
customerservic[email protected]om
CORRIDOR 7128
CONSOLE
2
Step 3 With help from another person, carefully position the cabinet A1 upside-down (as shown) or on its
back. Caution-do not remove blocking above the shelves. Attach the base to the cabinet with 6 Screws H2
using Hex Wrench T2. Do NOT fully tighten until all screws are started.
T2
2 Person Ta sk
H2 x 6
Step 2 - Attach the 2Leg frames A3 to Sub-frame A2 with 8Screws H1 using Hex wrench T2.
Make sure the red arrow on the sub-frame faces the same direction as the direction of the leg frames.
H1 Screw x 8
A2
T2
H1
Red
T2
A3
A2

bdiusa.com
customerservic[email protected]om
CORRIDOR 7128
CONSOLE
3
Step 5 - Place glass top C5 on top of the cabinet. Position glass flush with cabinet front doors.
2 Person Ta sk
Step 4 - With help from another person, carefully position the cabinet upright and install Door Pulls H5 using
Screws H3 and Screwdriver T1. Adhere Rubber Bumpers H4 about 1 inch (25mm) from edges of the cabi-
net as shown below.
2 Person Ta sk
H5
H5
H4
H4
H4
H4
H4
H4
H3
H3
C5

bdiusa.com
customerservic[email protected]om
CORRIDOR 7128
CONSOLE
4
Fine tuning your new BDI Corridor Home Theater Furniture
These steps are to be followed after you have unpacked and completed the simple assembly instructions for
your Corridor AV cabinet. Due to jostling in freight or perhaps an uneven floor, the doors on your Corridor cabinet
may not appear to be in perfect alignment. Making a few minor adjustments can rectify this situation. Be aware
that depending on your situation, patience and a bit of trial and error are required. The high-quality European
hinge hardware is infinitely adjustable, but changing one element can cause the need for further adjustments.
Through a little adjustment, you can modify the orientation of the cabinet doors to make sure that they are sitting
perfectly on your Corridor unit.
STEP 1 - Level your Corridor unit
Levelers are integrated into each leg assembly and are accessed at the bottom of each cabinet leg using Hex
Wrench (B2). If your floor is uneven, you may extend one or more levelers to attain a level, stable cabinet
placement. Turning the leveler clockwise will extend the leveler; turning it counter-clockwise will retract it.
CORRECT! Door is
sitting squarely and evenly
spaced on tops and sides.
INCORRECT! Door is
out of alignment with
the rest of the unit.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing
against the door frame.
If the cabinet’s doors appear out of alignment, this condition can be corrected with minor adjustment to the
European hinges on each door.
Because these hinges are infinitely adjustable, adjusting one
hinge element can sometimes cause the need for adjustments
to other elements. But with a few adjustments, you can modify
the orientation of the cabinet doors to make sure that they hang
perfectly within your cabinet.
Use the Phillips Screwdriver (A) supplied to adjust Corridor's
door hinges:
•By adjusting Screw 1, the door will move LEFT or RIGHT
within the frame. Make minor adjustments at both top and
bottom hinges for best results.
•By adjusting Screw 2 the entire door will move IN or OUT,
opening or closing the gap between the door frame and
cabinet. (This screw rarely needs adjustment.)
21
1
2