BEMIS bioBidet Bliss BB1700 User manual

OWNER’S MANUAL
BB1700

2 3
PRODUCT INFORMATION
Important Safeguards.............................................4
Main Unit & Parts......................................................10
Dimensions....................................................................11
Remote Control.........................................................12
Operation......................................................................14
PRODUCT INSTALLATION
Installation...................................................................25
Unit Separation.........................................................29
PRODUCT SETTINGS
Maintenance..............................................................30
Water Draining..........................................................32
Troubleshooting.......................................................33
Specifications............................................................34
WARRANTY
Warranty......................................................................35
Information to the User........................................38
TABLE OF CONTENTS

4 5
IMPORTANT SAFEGUARDS
DANGER - To reduce the risk of electrocution
WARNING - To reduce the risk of burns, electrocution,
fire, or injury to the persons
PLEASE OBSERVE THE FOLLOWING PRECAUTIONS
BEFORE USING THIS PRODUCT
READ ALL INSTRUCTIONS BEFORE INSTALLATION AND USE
1. Do not open the product to repair or remodel. Only qualified service
personnel should service this product. Do not use attachments not
recommended by the manufacturer.
2. Connect this product to a cold water supply pipe carrying potable
water. Do not connect to an industrial water supply line that does
not carry water of drinking quality. This will negatively effect hygiene
and performance.
3. Low Temperature Burns - A burn occurs when the skin has been exposed
to high temperatures. However, a low temperature burn may occur when
the skin has been in contact with an object at relatively low temperature
(about 104F). Close supervision is necessary when this product is used
by children or adults with sensitive skin.
4. If using any chemical toilet bowl cleaner, be sure to wipe up any spills
that splash onto the electric bidet. Do not use benzene or any acid
chemical detergent. Only neutral detergent permitted.
5. Do not plug in the power cord before connecting the water supply hose.
6. This product must be grounded. An approved Ground Fault Circuit
Interrupt must be used.
7. Do not splash water on this product. Please provide adequate ventilation
to avoid high levels of humidity which can damage the electronic
components. It is necessary to provide adequate ventilation with a fan,
open door, or open window when bathing.
GENERAL CAUTIONS
1. Never operate this product if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return the product to a
service center for examination and repair.
2. Do not stand or sit on the seat cover lid. It is not designed to
support a user’s body weight.
3. Allow the seat and lid to close automatically. Do not force the lid closed.
4. Do not strain or push the connected hose and tube connecter; it may
cause water leakage. Never drop or insert any object into any opening or
hose. Use proper plumbing suppliesif any modification is to be made.
5. Use this product only as described in the operating instructions.
Never use while sleeping or drowsy. Do not use while bathing.
6. Be careful so that this product does not become stained
with excrement and urine.
7. Drain the water from unit and unplug the power if this product is
not going to be used for an extended period of time.
8. Do not touch the power cord with wet hands. Do not reach
for a product that has fallen into water. Unplug immediately!
9. This product must be connected to a standard voltage power
source. Do not connect power cord if the cord is damaged or broken.
Do not plug the unit into a loose electric outlet.
10. Please disconnect the power cord when you clean this product or
detach it from toilet bowl. Do not supply electrical power to the unit
until the plumbing work has been completed.
11. Keep the electrical cord away from heated surfaces to prevent a
fire hazard. Also, keep any flammable materials away from this product
at all times.

6 7
IMPORTANT SAFEGUARDS (CONT.)
CAUTIONS BEFORE INSTALLATION:
WIRING REQUIREMENT
•THIS PRODUCT MUST BE PLUGGED into a regular voltage grounded
GFCI outlet (North America 120V ac). The rated power consumption is
1400W. In locations where only a standard two-prong outlet is available,
it is the responsibility of the user to install a grounded three-prong outlet.
Using a higher voltage is dangerous and may result in a fire or other
accident. This product is not responsible for damage resulting from
the use of it on other than specified voltage, or operating it without
proper grounding.
WARNING
•This product must be on a separate circuit. No other appliance should
share the circuit with this product. Sharing a circuit could cause the
branch circuit fuse to blow or the circuit breaker to trip. Continuous
usage under these conditions could result in fire or property damage.
GROUND INSTRUCTIONS
1. This product has a three-prong grounding plug, which must be plugged
into an outlet that is properly installed and grounded. In the event of an
electrical short circuit, grounding reduces the risk of electric shock by
providing an escape wire for the electric current. If repair or replacement
of the cord or plug is necessary, do not connect the grounding wire to
either flat blade terminal. The wire with insulation having an outer surface
that is green with or without yellow stripes is the grounding wire. Check
with a qualified electrician or service person if the grounding instructions
are not completely understood, or if in doubt as to whether the product
is properly grounded.
2. This product is for use on a nominal 120V circuit, and has a grounding
plug that looks like the plug illustrated in sketch A in Figure 1. A
temporary adapter, which looks like the adapter illustrated in sketches
B and C, may be used to connect this plug to a 2-pole receptacle as
shown in sketch B if a properly grounded outlet is not available. The
temporary adapter should be used only until a properly grounded outlet
(sketch A) can be installed by a qualified electrician. The green colored
rigid ear, lug, or the like extending from the adapter must be connected
to a permanent ground such as a properly grounded outlet box cover.
Whenever the adapter is used, it must be held in place by the screw.
OPTIONAL GROUND INSTRUCTIONS

8 9
IMPORTANT SAFEGUARDS (CONT.)
DANGER
•IMPROPER GROUNDING CAN RESULT IN A RISK OF ELECTRIC SHOCK.
Electric wiring has to be done in accordance with all local codes, or in the
absence of local codes, with the National Electrical Codes.
•The use of an extension cord is not recommended or advised. If it is
necessary to use an extension cord, use only a three-prong extension
cord (one to one), and a three slot built-in GFCI receptacle that will
accept the plug on this product. The marked rating of the extension
cord should be equal to or greater than the electrical rating of the unit
(10amp). Consult a qualified electrician or service person if you are not
sure whether the unit is properly grounded.

10 11
MAIN UNIT & PARTS DIMENSIONS
PosteriorWash Nozzle
Turbo Wash Nozzle
Digital Occupied Sensor
Drain / Quick Release
Operation LEDWindow
Heated Seat
Lid
Caution Label
Deodorizer
Dryer Vent
Control Panel for BB-1700
Feminine Wash Nozzle
Drain button
Cone packing
(2 pcs)
Mounting bolts (2 pcs) Catch Plate (1 pcs)
Nuts
(2 pcs)
Bolt Case
(2 pcs)
Water supply hose
(for electronic bidet)
Water supply hose
T-Valve L-Valve
1/2" O.D.Compression
Conversion Nut

12 13
REMOTE CONTROL
Stop all operation.
Posterior wash. Feminine wash.
Turbo Wash Dry washed area.
Adjust the water
pressure and warm air
dryer temperature.
Adjust the oscillation
function and nozzle
position (5 levels).
Adjust the water
temperature (4 levels).
Adjust the seat
temperature (4 Levels).
When selected during the
wash function, the nozzle
oscillates automatically for
a wider wash.
When selected during the
wash function,it starts the
massage wash.
If move button is selected
when user is not sitting on
the seat, it operates nozzle
shower function.
If massage function
is selected when the
user is not using wash
functions, it automatically
operates was and dry
function sequentially.
If Economy mode is
selected, seat temperature
and water temperature will
stay at 89.6°F.
When user sits on the
seat, it automatically
operates to deoderize.
(Can select on/off).
When you sit down on this product, sit on the center in order to activate the
sensor. (if the unit’s input water temperature is lower that 54°F, the water
temperature could be lower than the above noted temperatures.)

14 15
OPERATION
Please press the “off” or “low”button to reduce the seat
temperature after using. Special precautions should be taken for
children, those who cannot adjust the temperature, and those who
have sensitive skin.
DO NOT ALLOW CHILDREN TO USE THE TURBO WASH
or VORTEX WASH FUNCTION! SUPERVISION IS STRONGLY
RECOMMENDED FOR THE ELDERLY OR OTHER PERSONS
THAT MAY HAVE LIMITATIONS IN BODY MOVEMENT, ILLNESS
OR DISABILITIES.
1. Check for Water Leaks
•Please turn on the water supply
valve and check connected spots
(1~5) for the leakage.
2. Preparation
•Please plug the power cord into AC120V power outlet.
•Plug the unit into the proper power source and the LED
power light will start flashing.
•Wait until the LED power light stops flashing
and becomes solid red.
•The water tank will be filled after pushing a “wash”
(Posterior Wash, Feminine) button.
•When the water tank is filling the buzzer “Beeps”continuously.
•After the water tank is full the buzzer will end with
“One Solid Beep”.
•When you sit down on
the seat, the ORANGE LED
lamp on the control panel
will light up.
•When the digital sensor
on the seat is activated,
the operation LED window
on the main unit will
light “Occupied sensor”
and simultaneously, the
deodorizer fan will start
to work. (BB-1700/ BB-2000
Models)
•Press this button to
stop all operation.
3. Sit On Seat 4. Stop

16 17
5. Posterior Wash
1. Press “Posterior Wash”.
Automatically, the nozzle
comes out and sprays warm
water to posterior.
2. Additional functions during
your Posterior Wash
experience are available.
1. Press “Feminine Wash”.
Automatically, the nozzle
comes out and sprays
warm water to
feminine area.
2. Additional functions
during your Feminine
Wash experience
are available.
1. Press “Dry”, warm, dry air is
gently directed to washed
area for about 3 minutes.
2. You may adjust the warm air
temp. by pressing High and
Low (+, -) buttons.
3. This product memorizes the
air temperature of prior use.
•After sitting down on the
this product, the LED lamp
for water pressure on the
Power Control will light at
third or middle level.
•Press high or low (+, -)
to adjust the pressure of
the water spray to your
desired comfort level.
1. Press “Turbo Wash” or “Vortex Wash”, the nozzle spray is more
or focused to produce the effect of strong wash, to help s
timulate bowel movement.
2. Press “Water pressure - High & Low button”to adjust the water pressure.
3. Press “Turbo Wash”or “Vortex Wash”continuously for 3 to 5 seconds.
Automatically, the water nozzle comes out and sprays a warm stream of
water to the posterior center of the rectum.
4. If necessary, adjust “Position”of water stream with the (<, >) buttons.
5. Press “Water pressure High & Low button” (+, -) to
adjust the water pressure to your desired comfort.
6. Feminine Wash
7. Turbo Wash/Vortex Wash 8. Warm Air Dryer 9. Water Pressure
Adjustment
OPERATION (CONT.)
6. Press the “STOP” button when you feel your abdomen is full or wait until
the “Turbo Wash”or “Vortex Wash”function stops, approximately 1 minute.
7. You will shortly feel the urge to push the water out of your colon, push
the water and feces out as thoroughly as you can.
8. 6- Relax for a few minutes and be sure you feel your colon is empty and
then use the “Posterior Wash”and “Air Dry” function to finish.

18 19
OPERATION (CONT.)
•The temperature of water and seat are adjustable to the desired level
by pressing the “WATER” and “SEAT” button.
10. Warm Water/Seat Temperature Adjustment 11. Deodorizer
•Deodorizer ON/Off (initial setting is Off)
•Press button for 3 seconds (press the button again
for 3 seconds, the function is canceled.)
•After setting Deodorizer function, it is automatically
activated when sensing the human body.
•Once used, the Deodorizer function automatically
stops after 1 minute of operation.
•Deodorizer function stops while dryer is selected. After
dryer function completes, deodorizer automatically is activated.

20 21
OPERATION (CONT.)
•Nozzle position is adjustable to the desired position by pressing
“Front” or“Rear” (< , >) button from 1 to 5 positions. After using this
product, the nozzle will return to position 3.
•When using Posterior or Feminine Washing functions, pressing the
“MOVE” button will provide a short-motion, front to back oscillating
sprayfor a much wider cleansing experience.
•You may change the position of the Oscillating spray by pressing the
“MOVE” button again and “Front” or “Rear” buttons simultaneously.
•Push the “MOVE” button again and the oscillation motion
will stop automatically.
•Auto-Setting of Oscillation Feature - You can set this function to
automatically oscillate whenever the seat is occupied and the Posterior
or Feminine washes are in operation.
1. Sit on this product. Press the “MOVE” button for 3 seconds or until
you hear a single Chime.
2. Sit on the this product and proceed with Posterior or Feminine
Wash. In the automatic setting, you may still adjust the position of
the Oscillating spray by pressing the “Front”or “Rear”buttons.
12. Oscillation (Nozzle Movement Function) 13. Nozzle Position Adjustment
14. Massage (Rhythm Wash)
•When using the Posterior Wash or Feminine Wash functions,
pressing the“MASSAGE” button will provide a pulsation spray.
•You may change the pressure of the spray by pressing the
“High”or “Low” (+, -) buttons.
•Push the “MASSAGE” button again and the pulsating
action will stop automatically.
•Auto-Setting of Massage Feature
•You can set this function to automatically pulsate whenever the seat is
occupied and the Posterior or Feminine washes are in operation.
1. Sit on this product. Step 2: Press the “MASSAGE”button
for 3 seconds or until you hear a single Chime.
2. Sit on this product and proceed with Posterior or Feminine Wash.
In the automatic setting, you may still adjust the pressure of the
pulsating spray by pressing the “High” or “Low” (+, -) functions.
•Canceling the Automatic Oscillation function
1. Sit on this product. Press the “MOVE” button for 3 seconds or
until you hear a double Chime.
2. Press the “MOVE” button for 3 seconds or until you hear a
double chime.
•Canceling the Automatic Oscillation function
1. Sit on this product. Press the “MASSAGE” button
for 3 seconds or until you hear a double Chime.

22 23
OPERATION (CONT.)
•Saver On/ Off
•When pressing the energy
saver LED on the main unit
will turn on. (press button
again, the saver LED will
turn off)
•Energy saver mode
automatically maintains a
water and seat temperature
of 89.6F (32C).
•When using bidet in saver
mode, it is turned to
automatic saver.
•When you rise from the seat,
it goes into saver mode.
•Seat temperature is
maintained 32C.
Caution!
In energy saver mode, the seat
heating temperature could
appear to be lower than the
actual temperature setting.
OTHER ENERGY
SAVING TIPS:
•Keep seat cover closed
when not in use to prevent
heat from being lost.
•Keep temperature
set to low.
•Unplug the power cord
if you do not plan to use
the unit for a long period
of time.
•If the “MASSAGE” function
selected when user is not
using wash functions, it
automatically operates wash
and dry function sequentially.
•Wash (30 Seconds) + Dryer
(1 minute) then
automatically stops. •Press “Move” button while
seat is not occupied.
•Nozzle shower will initiate
to clean nozzle and tip for
about 20 seconds.
•Nozzle will automatically
retract once finished.
15. Auto Wash 16. Nozzle Shower 17. Economy (Energy Save Mode)
DEODORANT ENERGY
SAVER
POWER
BB-1700

24 25
OPERATION (CONT.) INSTALLATION
18. Nozzle Cleaning (Automatic & Manual)
Automatic
•This product has an automatic
nozzle self-cleaning function
that cleans the nozzle before
and after each use.
Manual
•Press the “Posterior”
button on the Auxiliary
Control panel on the
side of the seat without
occupying seat. The
nozzle will fully extend.
Gently clean the nozzle
with a soft cloth or
toothbrush.
•Press “Stop” button to
retract nozzle to stand
by mode.
•Shut off the water
supply shut off valve.
•Drain the toilet
tank completely.
•Then remove the
existing fill valve
water supply hose.
•Remove mounting bolts to
release existing toilet seat
from toilet.
•Remove existing supply
hose connected to the
toilet tank. Make sure
not to damage the water
supply hose.
•Install T-Valve at the
thread from tank.
•Beeping mode can be
enabled or disabled.
•To select or cancel silent mode,
press and hold down the “Stop”
and “Massage” remote buttons
simultaneously for approximately
3 seconds or until short beeps
•Single short beep - Silent mode
has been canceled
•Double short beeps - Silent mode
has been set
•The new setting will automatically
be saved if no other buttons
are pressed.
19. Selecting/Canceling Silent Mode
•Do not plug in before
installation.
•If you need an electric power
system or extension, please
consult a qualified electrician.
•Please contact our service
center (847-458-2334) when
you want to reinstall the
bidet product (move
or replacement).
1. Turn Off Water
2. Remove Existing
Seat & Lid
3. Connect T-Valve

26 27
INSTALLATION (CONT.)
4. Water Supply Hose 5. Installation
Catch Plate
6. Bolt & Nut Assembly
7. Assembly
8. Flexible Tube
•Remove existing supply tube
from fresh tank
•If your shut off valve is 1/2”
O.D compression size, use
supplied 1/2” conversion nut
as shown above.
•Slide cone packing and
washers onto the bolts then
fasten to securely mount
bidet seat to toilet.
1. Slide this product onto the catch
plate centering the unit with
the guide arrows on the base.
2. You will hear a click once this
product is securely mounted
to the catch plate.
3. This product will feel a little
loose on the toilet bowl. Adjust
the fit from front to back and
side to side for balance.
4. Tighten the nuts on
both bolts securely.
5. Check for any water leaks.
•Place the plate and guides
over each mounting hole.
Insert the mounting bolts
through the plate and
mounting holes.
•Connect the flexible tube from
side of T-Valve to this product,
Open the Angle Stop valve to
fill water.
•Check for any water leaks.
•Customers should use the
new hose set provided with
the product. Do not use used
set again.

28 29
9. Nozzle Change
INSTALLATION (CONT.) UNIT SEPARATION
Nozzle Separation
Nozzle Combination
Separation of Unit From Toilet Bowl
1. Disconnect the power plug.
2. Close water supply shut-off valve.
3. Drain water from bidet seat using drainage as illustrated.
4. Remove bidet seat from toilet as illustrated.
DO NOT TURN UNIT UPSIDE DOWN

30 31
MAINTENANCE
Cleaning The Nozzle
•When the “Posterior Wash”
button is pressed for 3 seconds
without occupying the seat, the
nozzle can be cleaned with a soft
toothbrush.
•After cleaning the nozzle, push
the “Stop” button once again, and
the nozzle retracts itself.
•Use of external water filter is only recommended in areas with known
hard water issues. If a filter is used, it must be replaced every 3 months.
•This product is designed and intended for use exclusively with Bio Bidet
Carbon & Iodine water filters. The purchase or use of any other water
filter is not the responsibility of BBC Innovation LLC. As such, any use of
non Carbon or Iodine water filters is prohibited and will void the warranty
for those Bio Bidet products. Bio Bidet will not be responsible for any
resulting damages or claims related to the misuse or distribution of non
BioBidet Carbon & Iodine filters.
•When you clean this
product, do not use
thinner, benzene or toilet
bowl cleaner. It may cause
damage to the surface
of unit.
•Use a wet cloth when
you clean this product.
•Do not spray water
directly on to this product.
•When you clean this
product, disconnect
the power plug.
This product will not operate properly if the strainer is clogged.
Please clean the strainer regularly.
1. Close the water shut off valve.
2. Flush the toilet to empty the water reservoir.
3. Unscrew the water hose nut.
4. Clean the strainer with a small brush or water
5. Re-screw the water hose nut.
6. Open the water shut off valve.
Cleaning The Body Of Unit
Water Filter Maintenance
Cleaning The Strainer

32 33
TROUBLESHOOTING
Trouble Cause Remedy
The
washing
water
does not
spray
1. The water tank
is not filled.
2. The shut off valve
is closed.
3. Freezing inside the
main unit or the water
supply pipe.
1. Wait about one minute.
2. Press the desired washing
button once again.
3. Turn on the shut off valve
to open.
4. Heat the room
(for about two hours).
Operating the unit while
parts are frozen will cause
a malfunction.
The unit
is not
operating
1. Disconnected the
power cord.
2. The seat is not
occupied.
3. The battery of remote
controller is exhausted.
1. Connect the power cord.
2. Check the power supply
system in your house.
3. Occupy the seat (The unit
has an occupied sensor).
4. Replace the battery.
Water is
leaking
Check the water
supply system
If water is leaking from the
main unit, call the service
center or the place you
purchased unit.
The washing
water pressure
is weak
1. The water pressure
level is set to “LOW”.
2. The strainer is clogged.
1. Set the water pressure
to “HIGH”
2. Clean the strainer.
The washing
water is not
warm
1. The water temperature
is set to “LOW”
2. Continuous operation
has depleted the
supply of warm water.
1. Set the water
temperature to “HIGH”
2. Wait about three minutes.
The seat and
dryer is not
warm
The seat & dryer
temperature is set to
“LOW”
Set the seat & dryer
temperature to “HIGH”
WATER DRAINING
Do not drink the drained water. Do not insert finger into the drain
hole. Before draining, unplug the power cord and wait 30 minutes
until the unit has cooled down.
Draining the Warm Water Tank in the Unit
Maintenance For Winter Season
If you do not intend to use this
product for 14 days or longer,
Drain the water from this product’s
warm water tank.
1. Disconnect the power plug.
2. Close the water shut
off valve.
3. Press the drain lever until the
water is completely drained
from water tank.
4. To re-supply water after
draining,open the water
shut off valve.
1. Check the power cord if it is plugged in or not.
2. Keep the water temperature on “Middle or High Level”
to prevent water from freezing.
3. If you do not intend to use the unit for 14 days or longer,
disconnect the power plug and drain the water.

34 35
SPECIFICATIONS
Specifications BB-1700
Power Rating America or Canada:
120Vac, 60Hz, 1400W
Water
Inlet
Type
Type Direct Inlet flow type
Water inlet pressure 0.04 ~ 0.74MPa(0.4 ~ 7.5 kgf/cm)
Power Cord 1.2m (4 feet): AMERICA
Wash
Device
Posterior Wash Max. 0.7l/min ( Max. 0.185 GPM )
Feminine Wash Max. 0.7l/min ( Max. 0.185 GPM )
Water Pressure
Adjustable
5 Levels
Warm Water
Temperature
Room Temp - Low, Normal, High
Heater 1340 W
Safety Devices Thermal fuse, Thermal switch,
Float switch
Heated
Seat
Temperature Room Temp - Low, Normal, High
Heater 55 W
Safety Device Thermal fuse
Warm
Air Dryer
Device
Adjustable Dry Temp (Room
Temp 55C)
Heated (250W)
Safety Device (Thermal fuse,
bi metal)
Turbo& Vortex Function
Inlet Water Temp. 3C~ 35C ( 37.4C ~ 95C )
Ambient Temp. 3C~ 40C ( 37.4C ~ 104C )
Dimension W : 460mm / L : 531mm / H : 152mm
Weight (kg) 4.9kg
WARRANTY
3 YEAR FULL COVERAGE WARRANTY
BBC Innovation LLC warranty its product to be free from manufacturing
defects under normal use and service for a period of three (3) years from
original date of purchase.
This warranty is extended only to the ORIGINAL PURCHASER.
BBC Innovation LLC’s obligations under this warranty are limited to repair or
replacement, at BBC Innovation LLC’s option, of products or parts found to
be defective, provided that such products were properly installed and used in
accordance with instructions.
•BBC Innovation LLC reserves the right to make such inspections as may
be necessary in order to determine the cause of the defect.
•BBC Innovation LLC will not charge for labor or parts in connection with
warranty repairs or replacements.
•BBC Innovation LLC is not responsible for the cost of removal, return
and/or re installation of products.
This warranty does not apply to the following items:
•Damage or loss sustained in a natural calamity such as fire, earthquake,
flood, thunder electrical storm, etc.
•Damage or loss resulting from any unreasonable use,
misuse, abuse, negligence, or improper maintenance of the product.
•Damage or loss resulting from removal, improper repair,
or modification of the product.
•Damage or loss resulting from sediments or foreign matter
contained in a water system.
•Damage or loss resulting from improper installation or from
installation of a unit in a harsh and/or hazardous environment.
This warranty gives you specific legal rights. You may have other
rights which vary from state to state. To obtain warranty repair service
under this warranty, you must take the product or deliver it prepaid to a
BBC Innovation LLC service facility together with a letter stating the
problem, or contact a BBC Innovation LLC distributor or products service

36 37
contractor, or write directly to
BBC Innovation LLC, 7900 Illinois Rte 31, Crystal Lake, IL 60014.
This written warranty is the only warranty made by
BBC Innovation LLC. Repair or replacement as provided under this
warranty shall be the exclusive remedy available to the purchaser.
BBC Innovation LLC shall not be responsible for loss of the product or for
other incidental, special or consequential damages or expenses incurred
by the purchaser, or for labor or other costs due to installation or removal,
or costs of repairs by others, or for any other expense not specifically
stated above. Except to the extent prohibited by applicable law, any implied
warranties, including that of merchantability or fitness for use, are expressly
limited to the duration this warranty. Some states do not allow limitations on
how long an implied warranty lasts, or the exclusion or limitation of incidental
or consequential damages, so the above limitation and exclusion may not
apply to you.
Warning!
BBC Innovation LLC shall not be responsible or liable for any failure of, or
damage to, this plumbing product or product component caused by either
chloramines in the treatment of public water supply or in-tank bowl cleaners
containing chlorine (calcium hypochlorite).
Note: The use of high concentration of chlorine or chlorine related products
can seriously damage the fittings. This damage can cause leakage and serious
property damage.
WARRANTY (CONT.)

38 39
INFORMATION TO THE USER
WARNING - Changes or modifications not expressly approved by
the manufacturer could void the user’s authority to operate the
equipment.
Note: The manufacturer is not responsible for any Radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one more
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.