Bircher Reglomat PrimeTec B User manual

1
PrimeTec
PrimeScan

  






PrimeScan B
a b
a b
1.
2.
*
PrimeTec B
A B C DA B C DA B C D A B C DA B C D
PrimeTec B
PrimeScan B
Combined detector AIR/Radar for opening and protecting automatically controlled sliding doors
Translation of the original instructions
General
1Safety instructions
2.1 Setting the AIR eld width (PrimeTec / PrimeScan)
2Mounting
ENGLISH
267087I
03/16
 Hood
 AIR light window
 Cable bushing
 Short Guide
 Mounting holes
 LED AIR: red (left)
 Button function (red)
 Button value (black)
LED radar: green (right)
AIR adjustment screw
 Radar module
 LCD display
a) red LED b) green LED
–Consider the national and international regulations on door safety.
–Only trained, qualied personnel may mount and start up the detector.
–The unit may only be opened and repaired by Bircher Reglomat.
–The unit may only be operated from a safety extra-low voltage (SELV)
system with safe electrical separation.
–Always consider the safety functions of your application as a whole,
never just in relation to one individual section of the system.
Start-up
Recommended start-up sequence: Mounting  Connection Initialisation
Mounting

A, D covered A, C, D covered C, D covered A, B, D covered A, B covered
Field width: 1 x 0.2 m
Field width: 0.5 x 0.2 m Field width: 1.2 x 0.2 m Field width: 0.5 x 0.2 m Field width: 1.2 x 0.2 m
1. Remove cover hood 3. Lay and connect cable
2. Set AIR eld width (see chapter 2.1) 4. Mount detector
The width of the AIR eld can be set using the click-in plastic cover in front of the detector’s lens.
1. Slide
2. Push & click!
–The installer is responsible for carrying out a risk assessment and in-
stalling the detector and the door system correctly.
–Avoid touching any electronic components.
–The door drive and transom prole must be grounded correctly.
Mounting the detector
2.2
Possible settings (Dimensions at 2.2 m mounting hight):
Detector without cover:
All light beams are active
Field width:
2.3 m x 0.2 m
at 2.2 m
1. Position drill template
2. Drill the holes, remove drill template
3. Lay cable and mount detector
Please keep for further use!
* Factory setting

2
1 2 1 2
1 21 2 1 2
0°
+ 1 … + 7°
– 1 … – 5°
–
+
5-10 cm
–
+
–
+
–
–
+
–
+
– +
1m
2m
3m
1m
2m
0m
0m
1m
2m
3m
4m
2.2 m


90°
1m
2m
3m
1m
2m
0m
0m
1m
2m
3m
4m
2.2 m
LCD 1 2 1
PrimeTec B / PrimeScan B
Cable
–
+
–
+
–
+
3 m
–
+
Radar AIR
Power Supply
1 white white
2 brown brown
3 green green
4 yellow
6 pink pink
5 grey grey
yellow
7 blue blue
8 red red
Radar output
Test
11.5 – 32 VDC
Controller
Radar
Test
AIR
AIR output
3Electrical connections
Connecting

Initialisation

4Initialisation
Remove all objects that do not form part of the usual door system environment from the
door area BEFORE switching on the power supply. Ensure that no people are in the door
area, otherwise correct startup will not be possible.
The alternate ashing shows the initialisation (teaching) of the detector. (Duration 20 - 25 seconds).
During startup, the rmware version FXXX is displayed.
Following initialisation, the red/green LED only illuminates when a detection has occurred.
The door system is now operational at this point. If any further settings are required, proceed as described in the following sections.
red LED green LED
5Mechanical ne tuning
5.1 AIR eld (PrimeTec / PrimeScan)
Settings of the inclination angle on the
adjustment screw:
Inclination :
– 5° ... +7° continuously adjustable
5.2 Radar eld (PrimeTec)
Manual settings of the
inclination angle
0° ... +90° in 5° steps
Manual settings of the
pivot angle
– 20° ... +20°in 5° steps
Wide radar eld turn 90° Narrow radar eld
Inclination angle: 35° Inclination angle: 35°
6Conguration using programming buttons (Operator buttons)
Automatic Cong. mode Choose Choose Funct./Parameter Back to choice Back to autom.
Operator buttons
red (Function)
black (Value)
A: Automatic mode
t: Test active
Radar
output on
 AIR
output on
Press shortly both
buttons
simultaneously
Red button:
switch
between Radar, AIR
and general
Black button:
choose
Red button:
Choose
parameter *
Black button:
Choose value of the
parameter
Press both
buttons
Press both
buttons
Switches to
automatic mode (A)
automatically after
1 min
* Value is going to be saved by switching to other parameters
min. = 0.5 m x 0.25 m (WxD)
max. = 4 m x 2 m (WxD)
min. = 0.16 m x 0.8 m (WxD)
max. = 2 m x 4 m (WxD)
General

3
Radar functions (PrimeTec) OPERATION OF THE BUTTONS1DESCRIPTION
Function (red) Value (black) LCD
Field size
1 1 – 5
1 = Smallest radar eld, ......., * = Medium radar eld, ......,  = Largest radar eld
Direction recognition
2 1 – 2
1 = both directions
* = forward
Cross Trac Optimisation CTO
41 – 2
1* = Off
 = On (recommended only at narrow eld)
Door lter
61 – 2
1* = Filter off,  = Door and interference lter on (EMV ows, e.g. uorescence tube)
Radar output
71 – 2
1* = active (NO)
 = passive (NC)
The Slow Motion Detection (SMD) is a factory setting. The SMD recognises slow motions after the detecor has been activated.
AIR functions (PrimeTec / PrimeScan) OPERATION OF THE BUTTONS1DESCRIPTION
Function (red) Value (black) LCD
Set sensitivity
1 1 – 5
2 = high sensitivity (acc. to EN16005 ≤ 3m, only indoors)
 = medium sensitivity (acc. to EN16005 ≤ 3m)  = low sensitivity (acc. to EN16005 ≤ 2.3m) * = normal sensitivity (acc. to EN16005 ≤ 2.6m) = very low sensitivity
Set teach-in time
21 – 5
2= 10 s * = 30 s = 60 s = 180 s = 15 min
AIR output contact logic
3 1 – 4
2= active (NO)
no detection contact open
* = passive (NC) no detection contact closed
Series connection Settings Master  ➔ Slave  Master  ➔ Slave 
Wiring: See series connection diagram: reglomat.bircher.com/en/ products-technologies/primefamily-b
AIR output
41 – 2
2* = On
= Off (AIR is going to be reactivated automatically after 15 minutes)
General functions (PrimeTec / PrimeScan)   OPERATION OF THE BUTTONS1DESCRIPTION
Function (red) Value (black) LCD
Reset
+
Press both buttons 8 seconds Initialisaiton and teaching of the background
Presetting (After presetting and leaving cong. a reset will be done automatically) 11 – 8
Press value for
1 second to change the
presetting
12= Standard, = footpath, = home for the aged, = wind screen,
= high door, = narrow door, = wide door, = factory settings
For all values set, parameter 0 is displayed
Combined outputs activated / not activated 2 1 – 2
12= activated (radar and AIR actuate the radar output)
* = not activated
AIR-frequency (In the case of overlapping AIR elds consider the addressing order: ➔odd nr. 1 ➔ even nr. 2➔odd nr. 3) 3 1 – 6
2
1* = Frequency 1,  = Frequency 2, = Frequency 3, = Frequency 4, = Frequency 5,
= Frequency 6
1 Press both buttons shortly for conguration mode *Factory setting

4
red LED green LED Fault Remedy
not
illuminated
continuously
lit
Radar tripping when door is closing 1. Set angle of radar further away from the door.
2. Adjust radar eld size.
Radar false tripping without
apparent external inuence
1. Avoid light sources (e.g. uorescent tubes) in the immediate vicinity of the detector.
2. No moving objects (plants, advertising posters, etc.) in the vicinity of the detector.
3. Avoid strong vibration at the radar detector
4. Possible inuence from a second radar detector in the vicinity (very unlikely)
continuously
lit
not
illuminated
AIR tripping when door is closing 1. Set angle of AIR detector further away from the door
AIR false tripping without apparent
external inuence
1. Avoid light sources (e.g. uorescent tubes) in the immediate vicinity of the detector.
2. Avoid puddles of water on the ground.
3. Avoid strong vibration at the AIR detector.
4. Inuence of overlapping AIR eld from another detector.
Set new Reglobeam address or CAN bus address.
5. Reduce sensitivity of the AIR (increase value).
not
illuminated
not
illuminated Door stays open 1. Switch AIR exit contact logic to other value
7Remedying malfunctions
8Technical data
9Declaration of conformity, identication of the year of manufacture by means of the serial number
7.1 Remedying false tripping
7.2 Remedying detector malfunctions
9.1 Declaration of conformity
red LED green LED Fault Remedy
ashing ashing
11: Self test (RAM/ROM)
2: Watchdog
1. Disconnect device from supply voltage
2. Restart device
3. If device displays fault again or does not start ➔renew device
ashing not
illuminated
25: AIR fault
6: AIR output fault
1. Disconnect device from supply voltage
2. Clean optics-cover and check for scratches
3. Restart device
4. If device displays fault again or does not start ➔renew device
Manufacturer: Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen
Authorised rep: Bircher Reglomat GmbH, Robert Bosch Strasse 3, D-71088 Holzgerlingen
Following directives have been observed: Manchinery directive 2006/42/EC, RoHS-Directive 2011/65/EU,
R&TTE-Directive 1999/5/EC until 12.06.2016, RED 2014/53/EU starting 13.06.2016,
EMC-Directive 2004/108/EC until 19.04.2016, EMC-Directive 2014/30/EU starting 20.04.2016
Following standards have been taken into account: EN16005:2012, BS7036-1:1996, BS7036-2:1996, EN ISO 13849-1:2008, EN12978:2003+A1:2009
EC type-examination certicate: 44/205/12/403013-003
Notied inspection centre: TÜV NORD CERT, NB 0044
Signee: Head of Sales & Marketing Damian Grand / Head of Operations Daniel Nef
Product variant: PrimeTec B ES, PrimeTec B ES/01, PrimeTec B ES/02, PrimeScan B
Technology Active infrared (wavelength: 880nm), radar double eld module ➔ PrimeTec (24.125 GHz)
Number of IR spots 24
IR spot dimensions 3 cm x 3 cm (at 2.2 m mounting height)
Response time < 200 ms
Mounting height 1.8 - 4 m
Angle setting of IR spots – 5° ... + 7° continuously adjustable
Power Supply ≤ 120 mA @ 11.5 ... 32 VDC
Power consumption < 4 Watt
Making current ≤ 240 mA
Output (AIR / Radar) Semiconductor relay: max. contact voltage 24 VAC / 34 VDC, max. contact resistance: 10 Ω
max. load current 40 mA, max switching capacity:
500 mW (AC) / 500 mW (DC)
Protection type Suitable for use acc. to IP54
Operating temperature -20° ... 60° C
Dimensionsn PrimeTec: 260 x 60 x 48.5mm (LxWxD), PrimeScan: 216 x 60 x 47.5mm (LxWxD)
Weight PrimeTec: 250g, PrimeScan: 180g
Estimated economic life-time 20 years
Manufacturer
Bircher Reglomat AG
Wiesengasse 20
CH-8222 Beringen
www.bircher-reglomat.com
Contact10
Identication of the year of manufacture
9.2
Year of manufacture
Week