Bircher Reglomat Herkules 2E User manual

1
111 mm
13 mm13 mm
35 mm
41 mm35 mm
13 mm
Mounting screws
Front view, 45° angle shown
Extra heigth
for tilted device.
28 mm 28 mm
13 mm
5 mm
5 mm
166 mm
1
111mm
13mm13mm
35mm
41mm35mm
13mm
Mountingscrews
Frontview,45°angle shown
Extraheigth
fortilteddevice.
28mm 28mm
13mm
5mm
5mm
166mm
1
111mm
13 mm
Mounting screws
Front view, 45° angle shown
Extra heigth
for tilted device.
28 mm28 mm
13 mm
5mm
5 mm
Hercules 2s
User Manual
Introduction
Quality
international
level
EN ISO
9001
Microwave motion sensor for
industrial doors
1
Box Contents & Tools Required
1.2
Hercules 2s sensor
with pre-wired 23’ (7m) 6-wirecable
A
B
C
A
B
C
D
D
Thebox contains the following items:
Tools recommended for installation:
Other items recommendedfor installation:
- Mounting screws (x2) sizedfor 3/16” (5mm) hole
- RC Duo2 remotecontrol (Part # S-RC2)
Self-adhesivemounting template
Instruction manual
Quick referenceguide for RC Duo 2 remote control
(stores in slot on battery compartment cover)
- Ladder
- Tape measure
- Level
- Drill with 1/4” (5mm) drill bit
- Electric screwdriver with
bit to match mountingscrews
- AWG 4 (5mm dia) wire stripper for cable sleeve
- AWG 24 (0.20 mm ) wire stripper for single wires
Product Description
1.1
Hercules 2s is an advancedplanar microwave motion sensor designed for industrial doors and gates. The sensor can differentiate
between people and vehicles. Its tworelay outputs can beprogrammedindependently for a multitudeof applications. Hercules 2s
alsofeatures cross-traffic optimization and slow-motiondetection.
2
TOP
TOP
A
B
C
D
D
FunctionRemote
Function
Values/
Description
Mounting
Height
A






2.0 – 2.5 m
2.5 – 3.0 m
3.0 – 4.0 m
4.0–5.0m*
5.0 – 6.0 m
6.0 – 7.0 m
Output
%QPƜI
uration
Output#1
(GreenLED)
Output #2
(Red LED)
B
C









Vehiclesforward*
Vehicles backward
Vehicles both dir
People forward**
People backward
People both dir
People/vehicles fwd
People/veh bkwd
People/veh both dir
Fieldsize/
Sensitivity
Output#1
Output #2
D
E





X-small/least sens.
Small/less sens.
Medium/norm sens.
Large/verysens.*
Xlarge/most sens.
Output
HoldTime
Output#1
Output #2
F1
F2








0.2 sec
0.5 sec
1.0 sec
2.0sec*
5.0 sec
Pulse on exit
Output steadily on
Output steadily off**
*FactorySettings**Factory Settings for output 2
Hercules2s350841A11/15
A
B
CD E F G
N
N
N
O
M
H
I
J
C
KL
Hercules2s
Microwavemotionsensorforindustrial doors
Originalinstructions
1Introduction
ENGLISH
350699
11/15
1.1ProductDescription
1.2BoxContents & ToolsRequired
1.3Partsof the Sensor
Hercules2sisanadvancedplanarmicrowave motion sensor designed for industrial doors and gates. The sensor can differentiate between
peopleandvehicles.Itstworelayoutputs can be programmed independently for a multitude of applications. Hercules 2s also features cross-
trafcoptimizationandslow-motiondetection.
AHousing(aluminum)
BMountingbracket
CInclinationanglehandscrews(x2)
DMicrowaveplanarmodule
EClipforwidedetectionpattern
(Usesettingforwideeldpattern- sec. 7.2)
FLeftbuttonLtosetfunction
GRightbuttonRtosetvalue
HOutput1indicator(greenLED)
IOutput2indicator(redLED)
JDIPswitches(forsetting
remotecontroladdresses1-4)
KRearcover
LConnectioncable
MFrontcover
NCoverscrews(x4)
ORegloBeam2remotecontrol
requiredtoaccesscompletesetoffunctions
Theboxcontainsthefollowingitems:
AHercules2ssensor
withpre-wired7m6-wirecable
BSelf-adhesivemountingtemplate
CInstructionmanual
DQuickreferenceguideforRegloBeam2remote control
(storesinslotonbatterycompartmentcover)
Toolsrecommendedforinstallation:
-Ladder
-Tapemeasure
-Level
-Drillwith5mmdrillbit
-Electricscrewdriverwith
bittomatchmountingscrews
-AWG4(5mmdia)wire stripper for cable sleeve
-AWG24(0.20mm)wirestripper for single wires
Otheritemsrecommendedforinstallation:
-Mountingscrews(x2)sizedfor5 mm hole
-RegloBeam2remotecontrol(Part # 292393)
TOP
TOP
A
B
C
D
FunctionRemote
Function
Values/
Description
Mounting
Height
A






2.0–2.5m
2.5–3.0m
3.0–4.0m
4.0–5.0m*
5.0–6.0m
6.0–7.0m
Output
Cong-
uration
Output#1
(GreenLED)
Output#2
(RedLED)
B
C









Vehiclesforward*
Vehiclesbackward
Vehiclesbothdir
Peopleforward**
Peoplebackward
Peoplebothdir
People/vehiclesfwd
People/vehbkwd
People/vehbothdir
Fieldsize/
Sensitivity
Output#1
Output#2
D
E





X-small/leastsens.
Small/lesssens.
Medium/normsens.
Large/verysens.*
Xlarge/mostsens.
Output
HoldTime
Output#1
Output#2
F1
F2








0.2sec
0.5sec
1.0sec
2.0sec*
5.0sec
Pulseonexit
Outputsteadilyon
Outputsteadilyoff**
*FactorySettings**Factory Settings for output 2
Herkules2E 350841A12/15
A
B
CD E F G
N
N
N
O
M
H
I
J
C
KL
Herkules 2E
Microwave motion sensor for industrial doors
Original instructions
1Introduction
1.1 Product Description
ENGLISH
350699A
12/15
Herkules 2E is an advanced planar microwave motion sensor designed
for industrial doors and gates. The sensor can differentiate between
people and vehicles. Its two relay outputs can be programmed in-
dependently for a multitude of applications. Herkules 2E also features
cross-trafc optimization and slow-motion detection.
AHousing (aluminum)
BMounting bracket
CInclination angle handscrews (x2)
DMicrowave planar module
EClip for wide detection pattern
(Use setting for wide eld pattern - sec. 7.2)
FLeft button Lto set function
GRight button Rto set value
HOutput 1 indicator (green LED)
IOutput 2 indicator (red LED)
JDIP switches (for setting
remote control addresses 1-4)
KRear cover
LConnection cable
MFront cover
NCover screws (x4)
ORegloBeam 2 remote control
required to access complete set of functions
The box contains the following items:
AHerkules 2E sensor
with pre-wired 7 m 6-wire cable
BSelf-adhesive mounting template
CInstruction manual
DQuick reference guide for RegloBeam 2 remote control
(stores in slot on battery compartment cover)
Toolsrecommended for installation:
- Ladder
- Tapemeasure
- Level
- Drill with 5 mm drill bit
- Electric screwdriver with
bit to match mounting screws
- AWG4 (5 mm dia) wire stripper for cable sleeve
- AWG24 (0.20 mm) wire stripper for single wires
Other items recommended for installation:
- Mounting screws (x2) sized for 5 mm hole
- RegloBeam 2 remote control
1.2 Box Contents & ToolsRequired
1.3 Parts of the Sensor
TOP
TOP
A
B
C
D
Function Remote
Function
Values/
Description
Mounting
Height A






2.0 – 2.5 m
2.5 – 3.0 m
3.0 – 4.0 m
4.0 – 5.0 m *
5.0 – 6.0 m
6.0 – 7.0 m
Output
Congu-
ration
Output #1
(GreenLED)
Output #2
(Red LED)
B
C









Vehiclesforward*
Vehiclesbackward
Vehiclesboth dir
People forward**
People backward
People both dir
People/vehicles fwd
People/veh bkwd
People/veh both dir
Field size/
Sensitivity
Output #1
Output #2
D
E





X-small/least sens.
Small/less sens.
Medium/norm sens.
Large/very sens.*
Xlarge/most sens.
Output
Hold Time
Output #1
Output #2
F 1
F 2








0.2 sec
0.5 sec
1.0 sec
2.0 sec*
5.0 sec
Pulse on exit
Output steadily on
Output steadily off**
*Factory Settings ** Factory Settings for output 2
Herkules 2E 350841A 12/15
A
B
CD E F G
N
N
N
O
M
H
I
J
C
KL
Herkules 2E
Microwave motion sensor for industrial doors
Original instructions
1Introduction
1.1 Product Description
ENGLISH
350699C
09/17
Herkules 2E is an advanced planar microwave motion sensor designed
for industrial doors and gates. The sensor can differentiate between
people and vehicles. Its two relay outputs can be programmed in-
dependently for a multitude of applications. Herkules 2E also features
cross-trafc optimization and slow-motion detection.
AHousing (aluminum)
BMounting bracket
CInclination angle handscrews (x2)
DMicrowave planar module
EClip for wide detection pattern
(Use setting for wide eld pattern - sec. 6.3)
FLeft button Lto set function
GRight button Rto set value
HOutput 1 indicator (green LED)
IOutput 2 indicator (red LED)
JDIP switches (for setting
remote control addresses 1-4)
KRear cover
LConnection cable
MFront cover
NCover screws (x4)
ORegloBeam 2 remote control
required to access complete set of functions
The box contains the following items:
AHerkules 2E sensor
with pre-wired 10 m 6-wire cable
BSelf-adhesive mounting template
CInstruction manual
DQuick reference guide for RegloBeam 2 remote control
(stores in slot on battery compartment cover)
Tools recommended for installation:
- Ladder
- Tape measure
- Level
- Drill with 5 mm drill bit
- Electric screwdriver with
bit to match mounting screws
- AWG 4 (5 mm dia) wire stripper for cable sleeve
- AWG 26 (0.20 mm2) wire stripper for single wires
Other items recommended for installation:
- Mounting screws (x2) sized for 5 mm hole
- RegloBeam 2 remote control
1.2 Box Contents & Tools Required
1.3 Parts of the Sensor

2
45°
125 mm
125 mm
50 mm41 mm
min.
50mm
111 mm
13 mm13 mm
35 mm
41 mm35 mm
13 mm
Mounting screws
Front view, 45° angle shown
Extra heigth
for tilted device.
28 mm 28 mm
13 mm
5 mm
5 mm
166 mm
x
x
5 mm
5 mm
+
–
+
–
Ensure sensor is rmly mounted
on a at surface. Avoid vibra-
tions.
Objects such as fans, plants,
ags, etc must not protrude into
the detection area.
Obstruction can effect perfor-
mace of sensor. Make sure sensor
has an unobstructed view.
Mount sensor away from uores-
cent or HID light sources.
1. Remove sensor unit from mounting bracket by loosening handscrews.
2. Afx the self-adhesive mounting template to the wall or ceiling and drill holes in specied lo-
cations. Remove the template once the holes have been drilled.
3. Route the cable through the opening in the mounting bracket and ensure cable length is suf-
cient to accomodate desired inclination angle.
4. Secure the mounting bracket tightly to the wall or ceiling using screws.
5. Attach sensor to mounting bracket by aligning the pins and screws on the sensor with the slots
on the mounting bracket. Ensure both sides are seated properly.Tighten handscrews to secure.
6. Connect cable to door operator (refer to door operator manual for wiring diagram).
Ideal mounting location
Center over door
Self-adhesive mounting template Optional ceiling mounting
Example of application
requiring tilt adjustment
Attaching the sensor to the bracket
After mounting, adjust the inclination angle to the desired detec-
tion pattern. Adjust the inclination angle by loosening the hand-
screws on the sides of the sensor and adjusting as shown below.
Range is 0 - 90°, in 15° increments as marked on the mounting
bracket. 30 - 45° is typical for most applications.
It may be necessary to tilt the sensor for certain applications (not recommended unless war-
ranted by special circumstances). To do so, loosen the handcrews and remove the sensor from
the bracket. Once the mounting screws are accessible, loosen them enough to twist the bracket
to change the tilt of the sensor.
2.1 Special Considerations
2Mounting the Sensor
2.2 Mounting Instructions
2.3 Inclination Angle
2.4 Tilt Angle

3
A
B
C
D
E
F
Function Remote
Function
Values/
Description
Mounting
Height
A






2.0 – 2.5 m
2.5 – 3.0 m
3.0 – 4.0 m
4.0 – 5.0 m *
5.0 – 6.0 m
6.0 – 7.0 m
Output
Congu-
ration
Output #1
(Green LED)
Output #2
(Red LED)
B
C









Vehicles forward*
Vehicles backward
Vehicles both dir
People forward**
People backward
People both dir
People/vehicles fwd
People/veh bkwd
People/veh both dir
Field size/
Sensitivity
Output #1
Output #2
D
E





X-small/least sens.
Small/less sens.
Medium/norm sens.
Large/very sens.*
Xlarge/most sens.
Output
Hold Time
Output #1
Output #2
F 1
F 2








0.2 sec
0.5 sec
1.0 sec
2.0 sec*
5.0 sec
Pulse on exit
Output steadily on
Output steadily off**
* Factory Settings ** Factory Settings for output 2
Herkules 2E 350841A 12/15
Power
10 - 36 VDC/
12 - 28 VAC
White
Brown
Green
Cable Yellow
Pink
Grey
Output 1
(Green LED)
COM
NO (NC)
Output 2*
(Red LED)
COM
NO (NC)
See table on pages 5 & 6 for detailed information
on output 1
See table on pages 5 & 6 for detailed information
on output 2
*Factory setting = Output 2 off
Startup sequence after power has been connected to the sensor:
-Both green & red LED’s begin to blink slowly
-Green LED will continue to blink quickly
The RegloBeam 2 remote control allows Herkules 2E to be easily and
conveniently programmed from the ground. Data transfer between the
RegloBeam 2 and Herkules 2E functions in both directions, i.e. to and from
the sensor by an infrared interface. The RegloBeam 2 reads back the ad-
justed values immediately after programming and displays them on the
remote to ensure accurate programming.
ATransmitter/receiver (infrared)
BStatus indicator LED
CNumerical buttons (1 to 9)
DFunction buttons (A to F)
EStart button:
a) Powers on (hold 2 sec)
b) Establishes connection to the sensor
FRemote function quick reference guide
(stored in slot on battery compartment cover)
This guide is included in every Herkules 2E box
The RegloBeam 2 must be powered on before use.
POWER ON: Press and hold Gfor 2 seconds
POWER OFF*: Press and hold Gfor 2 seconds
*The remote will automatically turn off after 2 minutes if no
button is pressed.
i
3Electrical Connection
4Introduction to the RegloBeam 2 Remote Control
4.1 Layout of the RegloBeam 2 Remote Control
3.1 Intialisation
4.2 Turning on the RegloBeam 2 Remote Control
Flashing buttons on the RegloBeam 2 indicate that the data has
not been fully transmitted.
Avoid exposing the infrared interface to direct sunlight or other light sour-
ces.

4
L
R
The RegloBeam 2 functions bidirectionally with the sensor. This means
that changes to the settings on the sensor are immediately signalled
back by the sensor to the remote control. If an additional parameter is
programmed within 2 minutes of the previous parameter, it is not ne-
cessary to press to re-establish connection to the sensor each
time.
The connection between the RegloBeam 2 and Herkules 2E can only be
established when the sensor is in programming mode (unlocked). Pro-
gramming mode is activated when the sensor is switched on. For sa-
fety reasons, this mode is automatically deactivated 30 minutes after
the last setting has been made on the sensor. The sensor can be locked
at any time by pressing followed by .
Programming mode can be activated in three different ways:
Ensure sensor is in
programming mode
(section 5.1)
Once blinks, press
again to establish
connection.
The sensor’s address
illuminates on the
keypad.
EXAMPLE:
address 
(factory setting)
Choose function to be
programmed. See
chart on following
pages for complete
list.
Press the desired
function (letter)
button.
EXAMPLE:
mounting height 
The sensor acknow-
ledges it’s current
setting by illuminating
it on the keypad.
EXAMPLE:
 = 4 – 5 m
(factory default)
Now press desired
new value.
EXAMPLE:
Desired height = 3 m
Choose  = 3 – 4 m
The new setting is
immediately saved and
displayed on the
keypad.
Programming of this
function is now
complete. Repeat for
other functions if
necessary.
i
Note: If any buttons are blinking, programming failed. In this case, repeat programming.
A) Restart the sensor
(temporarily disconnect the supply voltage) B)Brieypressoneofthebuttonsinsidethesensorunit,
Lor R
To access programming buttons, open the front cover of the sensor
by removing 4 screws.
Replace cover and close securely once button has been pressed.
C) Enter access code with remote control
1
2
Press to establish connection to the
sensor. The sensor address will illuminate.
Press followed by and enter the
4-digit preset access code, followed by .
EXAMPLE:

Sensor is now in programming mode.
If parameters cannot be changed (buttons
blink), repeat sequence.
If connection is still not established,
use option A or B above (no access code
was previously stored.)
4.3 Establishing Connection to the Sensor
5.1 Establishing Connection to the Sensor
5Functions & Settings - Programming by Remote Control

5
Sensor Function RegloBeam 2
Function
Description
Factory Settings in bold with *
Mounting Height A
Hight Value
2.0 – 2.5 m 
2.5 – 3.0 m 
’
3.0 – 4.0 m 
4.0 – 5.0 m  *
5.0 – 6.0 m 
'
5.0 – 7.0 m 
i
Ensure proper mounting height
is programmed for optimum
sensor performance
i
For people/vehicle separation
use mounting height 3mand up
i
For wide eld use mounting height
under 4 m
After mounting height is set, most typical
applications require no further program-
ming.
Output #1
Conguration
Green LED
Yellow & green
wires
?
In Out B
 *Vehicles forward
Vehicles backward
Vehicles both directions
People forward
People backward
People both directions
People & vehicles forward
People & vehicles backward
People & vehicles both directions
Output #2
Conguration
Red LED
Pink & grey wires
?
In Out C
Vehicles forward
Vehicles backward
Vehicles both directions
 *People forward
People backward
People both directions
People & vehicles forward
People & vehicles backward
People & vehicles both directions
Output #1
Field size/
sensitivity D
X-Small eld/least sensitive
Small eld/less sensitive
Medium eld/normal sensitivity
 *Largeeld/verysensitive
X-Large eld/most sensitive
Output #2
Field size/
sensitivity E
X-Small eld/least sensitive
Small eld/less sensitive
Medium eld/normal sensitivity
 *Largeeld/verysensitive
X-Large eld/most sensitive
* Factory settings
To activate
this output,
press F
followed by .. 
5.2 Programming Sensor Functions by Remote Control

6
Sensor Function RegloBeam 2
Function
Description
Factory Settings in bold with *
Output #1
Hold Time F1
0.2 sec
0.5 sec
1.0 sec
 *2.0 sec
5.0 sec
Pulse on exit
Output steadily on (for testing purposes only)
Output steadily off
Output #2
Hold Time F2
0.2 sec
0.5 sec
1.0 sec
2.0 sec
5.0 sec
Pulse on exit
Output steadily on (for testing purposes only)
 *Outputsteadilyo
Output #1 Logic F3 *NO
NC
Output #2 Logic F4 *NO
NC
Cross-Trafc
Optimization (CTO) F5
 *O-Dooralwaysactivateswhenanycrossing
Low - Door occasionally activates when crossing trafc is detected
Medium - Door rarely activates when crossing trafc is detected
 High - Door ignores most crossing trafc
Interference Filter F6
 *O
On - Use when electromagnetic sources such as uorescent bulbs,
HID lights, wireless systems, motors/inverters are causing interference
Slow Motion
Detection (SMD)
(People only)
F7
 *O
On - holds door open as long as people are slightly moving in front of the door
(LED will blink)
Remote control
communication
address F8
Set Access Code
(To unlock sensor
see page 4)
Delete Access Code
D9
i
Before setting access code, always use delete access code
To set access code, enter Dfollowed by any 4-digit number from
1 1 1 1 - 9 9 9 8 ending with D. Access code is now stored.
To delete access code, enter D9 9 9 9 ending with D.
Lock Sensor to
Remote Access F8 Forces sensor to exit programming mode.
Further changes cannot be made until programming mode is entered again
(See section 5.1).
Factory Reset ACompletes factory reset
All settings listed in this table with *will be restored.
* Factory settings
 –Available addresses that can be set by remote
 *Factory setting
Reads & sets address (1-4) set by DIP switch on sensor unit
Once address is changed, press Gto re-establish connection with sensor

7
L
R
L
R
1 2
O
N
1 2
O
N
1 2
O
N
1 2
O
N
L
R
Button L Button R
In cases when no remote control is available, several crucial functions
can be programmed by using the buttons on the sensor unit.
All remaining functions must be congured by remote control.
1. Unscrew all front cover screws and remove the front cover to locate
buttons.
1. Briey press Land Rsimultaneously to enter programming mode
3. Press button Lto change the function. The function increases by 1
for every button press. Once the last function has been reached, the
program returns to the rst function. The red LED ashes to indicate
the number of the activated function.
4. Press button Rto change the value. The value increases by 1 for
every button press. Once the last value has been reached, the program
returns to the rst level.
5. Briey press Land Rsimultaneously to exit programming mode
or wait 25 sec and the sensor will exit automatically.
Function Function #
(Button L /
Red LED)
Values
(Button R / Green LED)
Mounting Height 1 1-6 (see table on pg 5)
Output 1 Conguration 2 1-9 (see table on pg 5)
Output 1 Field Size/
Sensitivity
31-5 (see table on pg 5)
Wide Field Setting 4 1-2 (see sec. 6.3 below)
Value Wide Field Setting
1O*
2 on
* factory setting
6. Replace the front cover and tighten all 4 screws.
1. Activatethewideeldsetting
If wide sensing eld is desired, follow programming instructions
below and use the clip accessory on the sensor unit.
The sensor will not function correctly if the clip is used
withouttheproperwideeldsettingorviceversa.
The wide eld setting is only available for for mounting heights up
to 4 m. Sensor will not allow wide eld setting to be activated if a
higher mounting height is selected.
Normaleldwithoutclip* Wideeldwithclip
Briey press Land R
simultaneously to enter
programming mode.
Press L 3 times to enter
wide eld function. The red
LED will blink 4 times.
Press Ronce to turn on
wide eld and twice to turn
off (factory setting = off).
The green LED will blink the
corresponding # of times to
verify selection
Briey press Land R
simultaneously to exit
programming mode.
Changes are saved
immediately.
Unscrew the 4 front cover screws and remove the front cover of the
sensor to locate the DIP switches (refer to section 1.3 for more in-
formation). Ensure the cover is closed securely when addressing is
complete.
Address 1
Address 2
Address 3
Address 4
– Press Land Rsimultaneously and hold for 8 seconds.
– Every 2 seconds, one LED illuminates briey.
– Both LED’s illuminate after 8 seconds
– The reset is complete when both buttons are released.
6.3 Wide Field
6.1 Factory Reset
6.2 Programming Addresses 1-4 (by DIP Switch on the Sensor)
6Functions & Settings - Programming Sensor with Buttons on Unit
i
L
R
Red LED Green LED
L
R
L
R

8
9Conformities
7Troubleshooting
8Technical data
10 Warranty and liability
11 Contact
Bircher Reglomat AG
Wiesengasse 20
CH-8222 Beringen
www.bircher-reglomat.com
Manufacturer: Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen
Following directives have been observed: RoHS 2011/65/EU, RED 2014/53/EU
Product variant Herkules 2E
This device meets the requirements of Part 15 of the FCC regula-
tions and the RSS-210 standard of Industry Canada.
Warning: Changes or modications made to this equipment not
expressly approved by Bircher Reglomat AG may void the FCC
authorisation to operate this equipment.
1. The warranty and liability of Bircher Reglomat AG are based on the sales con-
tract.
2. The warranty and liability shall expire prematurely, should the client or third
parties not use and/or operate the product in compliance with existing opera-
ting instructions, should incorrect changes or repairs be made by the client or
third parties, should the client or third parties, when a fault has occurred, not
take suitable steps at once for a reduction of possible damage/losses and offer
Bircher Reglomat AG a chance for remedying the said fault.
3. The warranty and liability shall exclude any damage for which there is no proof
that it is due to poor materials, faulty construction, poor workmanship, and any
damage caused by other reasons, for which Bircher Reglomat AG cannot be held
liable.
4. No liability can be assumed for any consequential damage, provided this is not
governed otherwise by applicable product liability laws and regulations.
5. Warranty claims made against the seller on the basis of the sales agreement
are not affected by these regulations.
6. For the benet of its customers Bircher Reglomat AG constantly develops its
products further. Bircher Reglomat AG reserves the right to make changes to any
of the products described in this document without prior notice.
Fault Remedy
People/vehicle separation does not work as expected Check mounting height & setting (recommended > 3 m)
Check mounting situation & environment (best: sensor centered above door)
Check setting/clip for wide eld pattern
Late detection of trafc Increase eld size/sensitivity
Adjust inclination angle to move the pattern away from the door
Door reverses (sensor reacts to closing door) Adjust inclination angle to move the pattern away from the door
Reduce eld size/sensitivity
Make sure sensor is tightly xed and its mounting support does not vibrate
Door opens without motion of a vehicle (or person) Mount sensor away from EMC interference (e.g. uorescent tubes, HID lamps,
wireless system, motor/inverter, etc.)
Point pattern away from EMC interference
Activate interference lter
Door does not activate though sensors signals detection (LEDs) Check wire colors against output selection
Late detection or non-detection of people Reduce mounting height (recommended < 5 m)
Door stays open Change output logic
Technology Doppler radar with planar module
Transmitting frequency 24.05–24.25 GHz
Transmitting power < 20 dBm
Operating voltage 12–28 VAC, 12–36 VDC (45-65 Hz)
Operating current max 75 mA
Temperature range –30° bis 60° C
Air humidity 0% to 95% relative,
without condensation
Mounting height 2 to 7 m
Relay outputs
Switching voltage
Switching current
Potential-free changeover contacts
max 48 VAC/DC
max 0.5 A AC
Housing Aluminium black anodized,
Cover Polycarbonat
Dimensions 134 x 82 x 75 mm
Weight 820 g incl. cable
Protection class (EN 60529) IP 65
Max. detection speed 25 km/h for vehicles
Cable Length 10 m, 6 x 0.20 mm2
Suitable for the following
countries
EU, EFTA, US, CA
9.2 FCC approval
9.1 EC-Declaration of Conformity
Seller
Swissdoor ApS
Stenhuggervej 2
DK-5471 Søndersø
Tel.: [phone]
[email protected]
www.swissdoor.dk