Bircher Reglomat EsGate 2 User manual

When everything is connected correctly:
Status LED lights up green
Mode
Data
1
2
Original operating instructions (translation)
Safety an warning notices
EsGate 2, EsGate 2.LVAC
«Data» button
Version Operating vo tage safety edge safety edge Test input Output 1 Output 2 Signa output
EsGate 2
EsGate 2.LVAC
+/~
–/~
A1
A2
1
2
3
4
T1
T2
+
14
11
21
24
6
5
➔The electrical connection may only be set up by an electrician. ➔The arrangement of the components depends on the structural conditions and the
gate design. ➔Switch off the operating voltage before working on the system. ➔The switching device monitors pressure-sensitive protective devices
from Bircher Reglomat AG (proper use). ➔Use of components not supplied by Bircher-Reglomat (including safety edges) will render the guarantee and
liability null and void. ➔Connect all operating and switching voltages to the same fuse. ➔Connect the operating voltage to the same circuit as the indu-
strial door controller. ➔Disconnect device from mains in the event of a fault. ➔Protection max. 10 A
Switching device in combination with safety edges to
avoid dangers at crushing and shearing points in sliding gate systems
3
Electrical connection an terminal iagram
1
Operation Display
2
Dots
flash
Control buttons
on device:
Displays shown when safety edge is actuated: Status LED lights up orange
actuated: actuated:
«Mode» button
Stan ar operation
Please keep for futurereference!
ENGLISH
Diagnostic menu
4
Press the «Mode»and «Data»buttons simultaneously for 2 s ➔status LED flashes orange. Press «Mode»buttons briefly to change to the next
mode. Press the «Mode»button for 2 s to exit diagnostic menu.
Mode «r» Resistance
Error display mode
The 5 most recent errors
can be interrogated. Press
The resistances of the
safety edges are dis-
the «Data»key briefly in each
case, and the errors are dis-
played one after the other. End
appears when the «Data»button
is pressed for the 5th time. The
malfunctions are displayed in
chronological order (new ➔old)
played. Example:
8 = Resistance between
7 and 9 kohm.
1 = safety edge 
To access the next safety edge:
Press the «Data»button
12
CLOSE Output
OPEN Output
Mode
Data
Dots
Configuration mo e (for configuration before starting up, via diagnostic menu, after mode «h»)
5
Please read chapters 5.1 to 5.4 in full before attempting configuration.
Activating configuration menu
5.1
Status LED flashes orange,
press «Data» button
Press the «Mode» and «Data» buttons
simultaneously for 2 s.
Configuration menu is activated.
Configuration of safety edge inputs
5.2
Use the «Data» button to set the configuration
you want for the safety edge inputs
(according to Table 1).
The current setting for the safety
edge inputs is displayed.
Dysplay safety edge safety edge 
not configured
001* X X
002 X
003 X
UNC
*) Factory setting
Configuration menu can be exited at any time by pressing the «Mode» button (2 s).
«End» is displayed ➔Press «Data» button and release ➔Restart undertaken with new configuration.
Tab e 1
= Symbol for display flashes
Output 1: Press the
«Data»button
The Output 1
is deactivated
The Output 1 is
activated
Press the «Data»
button again
1
1
1
2
2
2
Mode «S» Output 1 Mode «S» Output 2
Both outputs: Press
the «Data» button
Both outputs are
deactivated
Both outputs are
activated
Press the «Data»
button again
12
12
12
12
Mode «I» Test input Mode «C» current
configuration
Mode «C» current configuration
test signal
Mode «h» current
fall-delay time
Modus «S» Simulation test
Display when
test input inactive
Display when
test input active
Displays current configu-
ration of safety edge
inputs, see configuration
table.
Displays current configura-
tion, test signal,
see test pulse table.
Displays current fall-delay
time, see fall-delay time
table.
Configuration ➔chapter 5 Configuration ➔chapter 5
Configuration ➔chapter 5
Active test input:
To access the config. mode:
Proess the «Mode» button
Output 2: Press the
«Data»button
The Output 2
is deactivated
The Output 2 is
activated
Press the «Data»
button again

Most important technical ata
8
Operating vo tage
EsGate 2 24 V AC/DC ± 15%,
EsGate 2.LVAC 100-240 V AC
50/60 z
Power consumption max. 3 VA
Safety edges 8,2 kOhm
Disp ay E001 E002 E006 E101/ E102
Error Safety edge malfunct.

Safety edge malfunct.

Mounting ≠config. mode Undervoltage/overvoltage
Remedy Check safety edge

Check safety edge

Check configuration Check supply
12
Error isplays
7
If an error is detected then the outputs are deactivated and symbols &and an error code are displayed. The status LED lights up red.
Should other fault messages appear, please contact your supplier.
Configuration fall- elay time
5.4
Display Fall-delay time
001 none
002 100 ms
003*200 ms
004 500 ms
005 1000 ms
Use the «Data» button to set the required fa -de ay time (according to Table 3).
Then briefly press the «Mode» button and End appears.
➔The system is configured.
➔Press «Data» button to restart.
*) Factory setting
Tab e 3
Error messages may occur when restarting
after configuration if the inputs do not match
the configuration.
Manufacturer: Bircher Reglomat AG, Wiesengasse 20, C -8222 Beringen
Employee responsible for documentation: Bircher Reglomat AG, Wiesengasse 20, C -8222 Beringen
Product: Switching device with inductive transmission system
Models: InTra6 2, InTra6 2.LVAC, InTra6 3, InTra6 3.LVAC; EsGate 2, EsGate 2.LVAC, EsGate 3, EsGate 2.LVAC (without transmiss.)
Serial numbers: 00240578[000000…900000], 00244423[000000…900000], 00263915[000000…900000],
00263916[000000…900000], 00263911[000000…900000], 00263912[000000…900000],
00263913[000000…900000], 00263914[000000…900000]
Notified Body: SUVA certificate authority, division: technics, EU-ID-number 1246
EC-type-examination certificates: E 6934 – E 6937
Following directives have been observed: Machinery directive 2006/42/EG, R&TTE Directive 1999/5/EG
Following standards have been taken
into account: EN ISO 13849-1, EN 12978
Signee: CEO, L. Oberholzer / Q SE, K. Kuhn, 18.8.2010, C -8222 Beringen
EC Declaration of conformity, ate of pro uction
9
260279D12/10
Configuration Test input
5.3
Use the «Data» button to set
the required test signa
(according to Table 2).
Display Test pulse
001
002*
Tab e 2 *) Factory setting
Outputs Semiconductor relay, 24 V DC, max. 50 mA
Test input 24 V DC ± 15% 2 mA
Not activated = Standard operation, activated = Test
Dimensions
(W x H x D) 22,5 x 94 x 88 mm
Signal output
6
Signal output closed when both outputs, 1 and 2, are closed. Actuation or fault ➔signal output open.
EC Declaration of conformity
9.1
Date of pro uction
9.2
See label ➔week/year, e.g. 12/10 = week 12, 2010
Manufacturer:
Bircher Reglomat AG
Wiesengasse 20
CH-8222 Beringen
Switzerlan
www.bircher-reglomat.com
Authorise representative:
Bircher Reglomat GmbH
Robert-Bosch-Strasse 3
D-71088 Holzgerlingen
Germany
www.bircher-reglomat.com
Contact ata
10