Bretford FP42MUL User manual

FP42UL FP42MUL
FP60UL FP60MUL
FLAT PANEL CART WITH OR
WITHOUT A PULL OUT SHELF
1
PARTS LIST
Cart Models: FP42UL, FP42MUL, FP60UL & FP60MUL
Qty Part# Description
1 022-3065 Right Rear Leg Assembly
1 022-3066 Left Rear Leg Assembly
2 022-3067 Front Leg Assemblies
1 010-5778 Top Shelf - FP42 Models
010-5794 Top Shelf - FP60 Models
1 010-5135 Middle Shelf - FP42 Models
010-5795 Middle Shelf - FP60 Models
1 010-1892 Bottom Shelf - FP42 Models
010-5796 Bottom Shelf - FP60 Models
1 022-2827 Handle Assembly
1 022-3068 Monitor Bracket - FP42 Models
022-3091 Monitor Bracket - FP60 Models
2 010-4953 Hook Bars
2 010-4956 Stop Brackets
2 015-0017 5” Stem Casters w/o Lock
2 015-0018 5” Stem Casters with Lock
Pull Out Shelf Models : FP42MUL & FP60MUL
Qty Part# Description
2 010-5783 Shelf Brackets - FP42 Models
010-5784 Shelf Brackets - FP60 Models
1 010-5782 Pull Out Shelf
1 030-1468 Left Outer Slide
1 030-1470 Right Outer Slide
2 030-1471 Inner Slides
Electrical Unit Models : FP42UL-E5BK, FP42MUL-EBK,
FP60UL-E5BK & FP60MUL-E5BK
Qty Part# Description
1 E6 UNIT 6-Outlet Electrical Unit
HARDWARE LIST
Ref Qty Part# Description
AA 22 030-0300-10T 5/8” Square Head Bolts
BB 24 030-0002 5/16-18 Hex Serrated Nuts
CC 2 030-1349 5/16-18 x 3/4” Hex Hd Screws
DD 2 SC1048B 1/4-20 x 45mm Bolts
EE 2 030-0207 1/4-20 Serrated Flange Nuts
FF 4 030-0401 5/8-18 x 1 1/2” Hex Head Screws
GG 4 030-0411 5/16-18 Serrated Nuts
HH 8 030-0304 1/4-20 X 5/8” Combo Truss Hd Screws
II 4 030-0865 #6 x 1/2” Button Pin-In Hd Screws
JJ 2 030-0354 10-32 x 1 1/2” Button Sockets Screws
1 010-1106 Hex Wrench
1 030-1352 1/8” Security Pin-In Driver Bit
1 044-2124 Courtesy Hardware Pack
This Pack Consists of:
(4) Metric M4 x 12 Screws
(4) Metric M4 x 30 Screws
(4) Metric M5 x 12 Screws
(4) Metric M5 x 30 Screws
(4) Metric M6 x 12 Screws
(4) Metric M6 x 35 Screws
(8) Small Washers
(20) Large Washers
(4) 5/8” Large Spacers
WARNING: FP42 carts are intended to hold monitors up to 75 lbs and FP60 carts
are intended to hold monitors up to 100 lbs. The use of a TV monitor weighing more
than that may result in instability causing possible injury. The top, middle and bottom
shelves are intended to hold equipment up to 50 lbs. on each shelf. The pull out
shelf on FP42MUL and FP60MUL is intended to support equipment up to 15 lbs.

2
BRACKET TO THE INSIDE
AA
These side holes are used for
installing the handle. Leave one of
the sides open to install the handle.
STEP 1
Position the top shelf onto the rear legs making sure the leg brackets are to inside of
the shelf. LOOSELY secure the shelf to the legs using screws (AA) and bolts (BB).
BB

3
Slide on middle shelf.
Slide on bottom shelf.
STEP 2
Slide the middle and bottom shelves onto the rear legs. Slide the front legs on. LOOSELY
install hardware to each corner, remembering to leave access for the handle.
AA
BB
INSTALL HARDWARE TO EACH
CORNER, OMIT HANDLE SIDE
Slide on front legs.
BB
AA

4
CC BB
STEP 3
Install handle to either side of the cart using bolts (CC) and nuts (BB).
STEP 4
Secure tube and top shelf together using screws (DD) and nuts (EE).
NOW TIGHTEN ALL CART CORNER HARDWARE
DD
EE

5
STEP 5
Push a caster into each leg insert. To ensure casters are securely in place, a rubber mallet may be used
to tap them in place. NOTE: The locking casters MUST be installed on the same side as the handle.
STEP 6
Attach the monitor bracket onto the front of the rear leg tubes as shown using bolts (FF) and nuts (GG).
FF GG

6
STEP 7
Attach each shelf bracket under the top shelf as shown using screws (HH).
STEP 8
Install the outer slide onto the shelf bracket by sliding TAB 1 into CUTOUT A and TAB 2 into CUTOUT B.
The pull out shelf should be installed opposite of the handle.
NOTE: Some bend in the bracket is ok as the slides and shelf will take care of that once
they are installed.
TAB 1 TAB 2
CUTOUT A CUTOUT B
This tab determines
where the shelf will
slide out from.
Each cart bracket has
additional cutouts to allow
the shelf to pull out from
either side of the cart.
SKIP TO STEP 12 IF YOUR CART DOES NOT HAVE A SHELF
HH
Make sure the bracket
cutouts face this way, if not
the bracket will be installed
upside down.

7
STEP 9
Install each inner slide into the outer slides. NOTE: Push inner slide in all the way until it snaps in.
Extend the slides to the positioning shown.
STEP 10

8
TAB 1
CUTOUT 1
TAB 2
CUTOUT 2
STEP 11
Install the pull out shelf by sliding CUTOUT 1 into TAB 1 and CUTOUT 2 into TAB 2.

9
TOP
BOTTOM
Attach both hook bars onto the back of your monitor using the mounting holes built into the case. A
courtesy hardware pack has been provided with several metric screw sizes. You may need to purchase
additional metric screws from your local hardware store for odd shaped monitors.
STEP 12
With someone’s help, hook your monitor onto the bracket as shown. (Monitor removed from picture for clarity.)
MONITOR NOT
SHOWN FOR CLARITY
STEP 13

Part # 031-8665
Rev. 05.11.11 CZ 10
Center your monitor horizontally and then tighten in place with screws (JJ).
Attach the stop brackets to the hook bars as shown with security screws (II) using the driver
bit provided.
II
JJ
CENTER MONITOR HORIZONTALLY THEN SECURE
II
JJ
STEP 15
STEP 14