Bretford TC12FF User manual

1
Qty Part# Description
1 022-2695 Top Shelf w/ grommet hole
2 010-4780 Keyboard Shelves
1 010-3953 Bottom Shelf
2 010-4785 Slide Brackets
1 022-2692 Right Front Leg
1 022-2691 Left Front Leg
1 022-2694 Right Rear Leg
1 022-2693 Left Rear Leg
1 022-2309 Wire Tray
2 015-0002 4” Casters w/o Lock
2 015-0003 4” Casters w/ Lock
2 030-1191 14” Full Extension Slides
1 CFPS UNIT Electrical Unit - TC12FF ONLY
PARTS LIST
Ref Qty Part# Description
AA 16 030-0300-10T 5/8” Square Head Bolts
BB 16 030-0002 5/16-18 Hex Serrated Nuts
CC 12 030-0325 1/4-20 x 1/2” Combo Screws
DD 16 030-1228 8-32 x 1/4” Combo Truss Hd Screws
EE 8 030-1203 #8-32 Acorn Nuts
GG 2 030-0302 #8-32 x 3/8” Screws - TC12FF ONLY
HH 10 02236 8-32 Hex Flange Nuts
I I 20 030-0240 1/4” External Lockwashers
1 010-1106 Hex Wrench
HARDWARE LIST
Hex Wrench (Provided)
Phillips Screwdriver
Rubber Mallet
TOOLS REQUIRED
TC12 / TC12FF
PRESENTATION CART WITH
AND WITHOUT POWER
These holes should
face UP as shown
These holes should
face IN as shown
Rear Legs - Stamped LR & RR
STEP 1
Lay the rear legs on a carpeted surface exactly as shown in FIGURE 1. (They are stamped “LR” & “RR”) Slide
bottom shelf and top shelf onto the legs so that the brackets are inside the shelves as shown in FIGURE 2.
Bracket MUST t
INSIDE shelf
Holes MUST
be ALIGNED
FIGURE 1
FIGURE 2

2
Slide the front legs onto the shelves so that the brackets are inside the shelves as
shown. NOTE: Make sure all bracket holes are aligned with the shelf holes.
Holes MUST
be ALIGNED
STEP 2
STEP 3
Secure shelves and legs together with bolts (AA) and
nuts (BB) in each corner as shown.
AA BB

3
STEP 4
STEP 5
Insert each caster into the bottom of each leg. If caster does not insert easily,
use a rubber mallet to tap caster in place. Once caster are SECURELY in
place, stand unit upright.
Attach each slide bracket using screws (CC) and washers (I I) as shown. Note
the position of the cart. One bracket is parallel with the back edge of the
top shelf and the other one is parallel with the front edge of the top shelf.
CC
BACK EDGE OF TOP SHELF
I I

4
STEP 6
STEP 7
Separate each slide and attach outer slide piece (2 per bracket) to the
slide brackets using screws (DD) and nuts (EE) as shown. NOTE:
Slide may need to be extended some to align attachment holes.
DD EE
CC
Slide cord bin between the rear legs as shown in
FIGURE 3. Attach through the inside with screws
(CC) and washers (I I) as shown in FIGURE 4. The
pictures on the next page show how to achieve a
xed or an adjustable position.
FIGURE 3
FIGURE 4
I I
NOTE: Separate slides
by pulling on black tab.

5
FIXED POSITION ADJUSTABLE POSITION
LEG
CORD
BIN
LEG
CORD
BIN
SHELF SHELF
STEP 8
Attach inner slide piece to keyboard shelf with screws (DD), washers (I I) and nuts (HH).
DD HH I I

6
Part # 031-7452
Rev. 04.21.08 CZ
STEP 9
Slide each keyboard shelf into each side of the cart.
STEP 10 FOR TC12FF ONLY
Attach the CFPS electrical unit onto the cord bin
slots with screws (GG) and nuts (HH).
HH
GG