Bretford TC15 User manual

1
Qty Part# Description
2 022-2708 Leg Assembly Stamped with “X”
2 022-2709 Leg Assembly Stamped with “O”
1 022-2695 Top Shelf w/Grommet Hole
1 022-2699 Middle Shelf w/Grommet Hole
1 010-4791 Bottom Shelf
2 010-4785 Slide Bracket
2 030-1191 Slide
2 010-5053 Keyboard Shelf
1 010-4788 Front Panel
1 010-4789 Rear Panel
2 022-2697 Left Door Assembly
2 022-2698 Right Door Assembly
1pr. 030-1206 Rack Rail
4 010-4799 Rail Bracket
2 010-4867 Utility Shelf
2 015-0002 4” Caster w/o Brake
2 015-0003 4” Caster w/ Brake
1 E12 Electrical Unit - TC15FF ONLY
PARTS LIST
Ref Qty Part# Description
AA 24 030-0300-10T 5/8” Square Head Bolts
BB 24 030-0002 5/16-18 Hex Serrated Nuts
CC 36 030-0325 1/4-20 x 1/2” Combo Screws
DD 16 030-0240 1/4” External Lockwashers
EE 16 030-1228 8-32 x 1/4” Combo Truss Hd Screws
FF 8 030-1203 #8-32 Acorn Nuts
GG 10 02236 8-32 Hex Flange Nuts
HH 4 030-0023 #6-32 x 3/8” Rnd Hd Machine Screws
I I 4 030-0522 6-32 Locknuts
JJ 8 030-0256 1/4-20 Flange Nuts
KK 2 030-0302 #8-32 x 3/8” Screws - TC15FF ONLY
MM 8 030-0402 #10-32 x 5/8” Combo Screws
NN 8 030-0383 #10 x 1/2” “AB” Truss Hd Screws
1 010-1106 Hex Wrench
2 010-1188 Door Stop Brackets
4 012-0286 Plastic Door Handles
HARDWARE LIST
Hex Wrench (Provided)
Phillips Screwdriver
Rubber Mallet
TOOLS REQUIRED
TC15 / TC15FF
19” RACK PRESENTATION CART
WITH & WITHOUT POWER
Assembly Instructions

These 5 holes
MUST FACE UP
These 2 holes
MUST FACE IN
LEG BOTTOMS
STEP 1
Lay the rear legs on a carpeted surface exactly as shown in FIGURE 1. Slide bottom and
middle onto the legs so that the brackets are inside the shelves as shown in FIGURE 2.
FIGURE 1
Bracket MUST
t INSIDE
shelf
Holes MUST
be ALIGNED
FIGURE 2
Slide the front legs onto the shelves so that the brackets are inside the shelves as
shown. NOTE: Make sure all bracket holes are aligned with the shelf holes.
Holes MUST
be ALIGNED
STEP 2
2

3
STEP 3
HAND TIGHTEN shelves and legs with bolts (AA) and nuts (BB).
ONLY install side hardware and middle shelf hardware as indicated.
FULLY TIGHTEN MIDDLE SHELF HARDWARE.
AA BB
STEP 4
Insert each caster into the bottom of each leg. If caster does not insert easily,
use a rubber mallet to tap caster in place. Once caster are SECURELY in
place, stand unit upright.
ONLY INSTALL IN
THESE LOCATIONS
BOTH SIDES
FULLY
TIGHTEN
THESE
ON BOTH
SIDES

4
STEP 5
Attach L-brackets to one side of the cart. These should be mounted on
the side that you wish the utility shelves to be installed on. Attach each
bracket (2 per shelf) with screws (CC) and nuts (JJ) as shown.
MIDDLE SHELF ATTACHMENT
BOTTOM SHELF ATTACHMENT
CC JJ

5
MIDDLE SHELF ATTACHMENT
BOTTOM SHELF ATTACHMENT
STEP 6
Attach the rack rails to the L-brackets with screws (CC) and nuts (JJ) as shown.
The threaded holes (smaller) are facing out.
CC JJ
NOTE, THE RACK RAIL MUST BE INSTALLED AS SHOWN.
TOP DOWN VIEW OF INSIDE CART
INCORRECTCORRECT

6
STEP 7
Attach each slide bracket using screws (CC) and washers (DD) as shown.
CC DD
STEP 8
Separate each slide and attach outer slide piece (2 per bracket) to
the slide brackets using screws (EE) and nuts (FF) as shown. NOTE:
Slide may need to be extended some to align attachment holes.
EE FF
NOTE: Separate slides
by pulling on black tab.

7
STEP 9
Attach inner slide piece to keyboard shelf with screws (EE), washers (DD) and nuts (GG).
EE GG
DD
STEP 10
Attach door stop brackets to both side of the bottom
shelf with screws (HH) and nuts (I I) as shown.
HH I I

8
Panel bottom ange
MUST hook onto
bottom shelf
Attach side panel in each corner with bolts (AA)
and nuts (BB). HAND TIGHTEN FOR NOW.
STEP 11B
Carefully, lay cart down as shown and slide on front panel (the one without the grommet hole).
Make sure panel’s bottom ange hooks onto the bottom shelf. NOTE: Rear panel (the one
with a grommet hole) goes on the same side of the cart as the grommet hole in the middle shelf.
Carefully, stand cart up and then from INSIDE the cart,
attach side panel to legs using screws (CC) as shown.
STEP 11C
ONCE THESE STEPS ARE COMPLETE
REPEAT THEM FOR THE REAR PANEL.
STEP 11A
CC

NOW TIGHTEN ALL CORNER BOLTS
AND NUTS ON THE ENTIRE CART.
9
STEP 12
Slide top shelf onto cart as shown. Secure all 4
corners with bolts (AA) and nuts (BB).
STEP 13 - FOR TC15FF MODELS ONLY
Attach the UCSE10 unit to rear panel as shown using screws (KK) and nuts (GG).
GG
KK

STEP 14
Attach the utility shelves to the rack rails as shown with screws (MM).
NOTE: You can install the shelves in any desired location along the rails.
MM
10
STEP 15
Attach a handle to each door using screws (NN) as shown.
NN

STEP 16
Attach the doors to each side of the cart using screws (CC) as shown.
CC
11
STEP 17
Slide both keyboard drawers into the cart.
Part # 031-7463
Rev. 08.13.10 CZ