BROSA Dakota Pendant Light User manual

Dakota
Pendant Light
A S S E M B LY GU I D E
V1

FOR YOUR SAFETY
Lift, don’t drag. This protects
your floor and product.
Avoid loose screws. Tighten
fixtures every few months.
Assembly requires 2 people.
It's always easier with a
friend.
Contact our support online
or call 1300 027 672.
Check the assembly guide
for required components.
?
Assembling this product on
a soft surface protects its
finish.

Safety
1. For indoor use only.
2. This light must be installed by a qualified electrician.
3. Follow instructions carefully. Any deviations may be hazardous, or
void your warranty.
4. If the external cable is damaged, it should be replaced immediately
by a certified electrician.
5. Always shut off power to the circuit before starting installation work.
6. The fitting is double insulated.
7. Under no circumstances may any part of it be attached to an earth
wire or terminal.
8. Connect the switched live conductor of your house wiring (normally
Brown or Red) to the live terminal or wire which is marked “L” or “Live”
and/or coloured Brown. Connect the neutral conductor of your house
wiring (normally Blue or Black) to the neutral terminal or wire which is
marked “N” or “Neutral” and/or coloured Blue.
9. Double check all the connections are secure and that no loose
strands of wire are left out of the connector.
10. Never use a bulb of a greater wattage than recommended.
11. This product is not suitable for children under 14 years of age.
12. Periodically check and re-tighten all screws and fasteners.
13. Switch off and wipe down your light with a clean cloth as needed.
14. Firmly secure all pieces. Small parts may present a choking hazard.
Notes:
1. Bulb is not included.
2. The cable length can be adjusted.
3. If the glass is cracked or broken, please stop using the product.
MAX.25W E27
220-240V ~ 50Hz

Components
Hardware
Before you get started, check you have all of the pieces below.
If anything’s missing, we’ll sort it out right away. Simply visit:
www.brosa.com.au/pages/product-return-and-parts-request
A x 2 B x 2
Light Body x 1
①
Shade x 1
②

Wall Fixings
Wood
If fixing to wood
make sure that it
isn’t chipboard as
screws can easily
pull away from the
core structure.
Brick or Masonry
Use an appropriate
wall plug provided
you are sure your
wall is sound.
Cavity Wall
Special toggle wall
plugs are needed.
Seek expert
advice.
Because of the variety of wall compositions, we can’t provide you with
appropriate wall fixings. Please identify your wall composition and
contact your local hardware store to get the appropriate fixings.
What You Need

Step 1 Unscrew the bolts attached to the ceiling rose
using a Phillips head screwdriver. Remove both
bolts and the mounting bracket attached to the
ceiling rose. Keep the removed bolts and
mounting bracket for the following assembly.
①

Step 2 To adjust the length of the cable:
Loosen the rubber screw attached to the cable
holder with a Phillips head screwdriver.
Adjust the cable held by the plastic clip to its
desired length.
Tighten the rubber screw again to secure the
cable in place.

Step 3 Before attaching, check wall for hidden pipes and
cables.
Locate the terminal of your house wiring and
place the mounting bracket against the ceiling
beside the terminal. Mark location for fixings
using a pencil through the bracket slots.
Remove the bracket and drill holes for the wall
plugs using a drill.
Instructions below demonstrate how to attach the light to the wall
using the provided wall plugs. However please do identify the type of
your wall and choose the appropriate wall fixings.

A x 2
Step 4 Knock the plugs A into the holes using a hammer.
Place the mounting bracket against the wall again
and fix the bracket in place with the screws B.
B x 2
AA
BB

Step 5 Distinguish live conductor (Brown or Red) from
neutral conductor (Blue or Black) of your house
wiring. Open the lid of the junction box and
distinguish live terminal (marked “L”) from neutral
terminal (marked “N”).
Lead the cables of your house wiring through the
pipe to the junction box.
Insert the live and neutral wire into corresponding
holes of the junction box.
Tighten the connections with a flat-head
screwdriver.
L
L
N
N
Brown/Red Blue/Black

Step 6 Align the ceiling rose with the mounting bracket
and make sure the bolt holes on each part
overlap. Insert the bolts removed in Step 1 into
both holes and tighten them with a Phillips head
screwdriver.

Step 7 Gently screw the correct bulb (not included) into
the bulb holder.

Step 8 Unscrew and detach the bolts attached to the
hanging bracket.
Attach the shade ② to the hanging bracket and
make sure the holes on the cup of the shade
overlap with the holes on the bracket.
②

Step 9 Insert the bolts again into the holes on the cup
and secure the shade in place by tightening the
bolts.

Step 10 Check all parts are secure.
Enjoy! We hope your new Dakota Pendant Light
lights up your life.