BROSA Orion Floor Lamp User manual

Orion
Floor Lamp
A S S E M B LY GU I D E
V3

FOR YOUR SAFETY
Lift, don’t drag. This protects
your floor and product.
Avoid loose screws. Tighten
fixtures every few months.
Assembly requires 2 people.
It's always easier with a
friend.
Contact our support online
or call 1300 027 672.
Check the assembly guide
for required components.
?
Assembling this product on
a soft surface protects its
finish.

Safety
1. For indoor use only.
2. Follow instructions carefully. Any deviations may be hazardous, or
void your warranty.
3. The external flexible cable or cord of this luminaire cannot be
replaced; if the cord is damaged, the luminaire shall be destroyed.
4. Never use a bulb of a greater wattage than recommended.
5. To replace the bulb, unplug the lamp from its power source and
allow it to cool first. Then change the bulb, plug it in and switch it on.
6. This product is not suitable for children under 14 years of age.
7. Periodically check and re-tighten all screws and fasteners.
8. Switch off and wipe down your lamp with a clean cloth as needed.
9. Firmly secure all pieces. Small parts may present a choking hazard.
Notes:
1. Bulb is not included.
MAX.40W E27
220-240V ~ 50Hz

Components
HardwareHardware
Before you get started, check you have all of the pieces below.
If anything’s missing, we’ll sort it out right away. Simply visit:
www.brosa.com.au/pages/product-return-and-parts-request
A x 1 B x 1
②
③
①Stand x 1 Shade x 1
Base Plate x 1
Base Weight x 1
④

Step 1 Unscrew the bolts and nuts with the spanner B
and remove them from the joint along with the flat
washers. Keep the removed parts for the
following assembly.
B x 1
B

Step 2 Re-arrange the cable as shown in the diagram
below.
Fit the lower part of stand into the joint.
Fit the parts removed in Step 1 back to the joint
again and then tighten them with the spanner B.
B x 1
B

Step 3 Unscrew the nut from the bottom of the stand
with the spanner B.
Remove the nut along with the spring washer and
flat washer.
Keep the removed parts for the following
assembly.
B x 1
B

Step 4 Align the base plate ③with the rods on the
bottom of the stand followed by the base weight
④ and make sure the long rod protrudes from the
bottom of the base weight.
Fit the flat washer onto the rod followed by the
spring washer and then the nut. Tighten the nut
using the spanner B.
B x 1
③
④
B

Step 5 Unscrew the nut from the top of the stand using
the spanner B.
B x 1
B

Step 6 Attach the shade ②to the top of the stand and
make sure the rod protrude from the brace. Fit
the nut removed in Step 5 to the rod and tighten
it with the spanner B.
B
②
B x 1

Step 7 Unscrew the shade ring and remove it from the
bulb holder.
Unscrew the bolts that fasten the bottom shade
panel with the Allen key A. Remove the bottom
shade panel and the bolts and place them aside
for the following assembly.
A x 1
A

Step 8 Lead the bulb holder through the hole on the top
of the shade and make sure it fits into the bracket
inside the shade.

Step 9 Attach the shade ring to the bulb holder again
and screw it until the bulb holder is tight and
secure.
Gently screw the correct bulb (not included) into
the bulb holder.

Step 10 Align the bottom shade panel with the bottom of
the shade again and fix it in place with the bolts
removed in Step 7 and Allen key A.
A x 1
A

Step 11 Direct the light where you want it as the light arm
and shade are adjustable.
Enjoy! We hope your new Orion Floor Lamp lights
up your life!