Burkert S070 User manual

S070
p. 1/4www.burkert.com
Positive displacement sensor fitting
for continuous flow measurement
This positive displacement sensor fitting is specially designed for flow measurement and/or batch control of highly viscous fluids like glue, honey or oil.
This measuring element must be associated to an electronic module SE30, SE32, SE35, SE36 with hall sensor principle only, quickly
and easily connected together by a Quarter-Turn.
The design of this fitting is based on the oval rotor principle. This has proven to be a reliable and highly accurate volumetric method of
measuring flow. Exceptional repeatability and high accuracy over a wide range of viscosities and flowrates are features of that design.
The low pressure drop and high pressure rating make it suitable for both gravity and pump (in-line) applications.
Type 8070
Positive displacement
flowmeter
Type 8072
Positive displacement
flowmeter
Type 8075
Positive displacement
flowmeter
Type S070 can be combined for...
• DN15 to DN100
• INLINE Quarter-Turn technology
• Electronics available for indication, monitoring, trans-
mitting, On/Off control and batch control
General data
Compatibility With electronic SE30, SE32, SE35, SE36
with Hall sensor principle (see separate data sheet)
Wetted parts ma-
terials
Body
Rotor
Shaft
Seal
Aluminium, stainless steel (316F)
PPS, aluminium, stainless steel (316F)
Stainless steel (316F)
FKM or FEP/PTFE encapsulated
Environment
Ambient temperature 0 to 60°C (32 to 140°F) (operation and storage)
Standards, directives and approvals
Protection class IP66 (NEMA 6)
Directives
Pressure Complying with article 3 of §3 from
97/23/CE directive*. (without CE mark)
* For the 97/23/CE pressure directive, the device can only be used under following condi-
tions (dependent on max. pressure, pipe diameter and fluid).
Type of fluid Conditions
Fluid group 1, §1.3.a Forbidden
Fluid group 2, §1.3.a DN 32, or DN > 32 and PN*DN 1000
Fluid group 1, §1.3.b PN*DN 2000
Fluid group 2, §1.3.b DN 200
Type 8076
Positive displacement
flowmeter
Complete device data
Pipe diameter
Thread connection
Flange connection
DN15 to DN100
½”; 1”; 1½”; 2”; 3” (G or NPT)
25; 40; 50; 80 or 100 mm DIN PN16 flange
1”; 1½; 2”; 3” or 4” ANSI 150LB flange
Measuring range
Viscosity > 5 cps
Viscosity < 5 cps
2 to 1200 l/min (0.53 to 320 gpm)
3 to 616 l/min (0.78 to 160 gpm)
Medium tempera-
ture max.
Aluminium body: 80°C (176°F)
Stainless steel body: 120°C (248°F)
Medium pressure
max.
DN15
DN25
DN40/DN50
DN80
DN100
55 bar (798.05 PSI) (threaded process connection)
55 bar (798.05 PSI) 1)
18 bar (261.18 PSI)
12 bar (174.12 PSI)
10 bar (145.1 PSI)
Viscosity 1000 cps. max. (higher on request)
Max. particle size 250 m - To prevent damage from dirt or
foreign matter, we strongly recommend the
installation of a 250 m strainer as close as
possible to the inlet side of the meter.
Accuracy ±0.5% of Reading
Repeatibility ±0.03% of Reading
1) or in accordance to the value of the used flanges

S070
p. 2/4
Installation and operation
The sensor fitting can be installed in any orientation as long as
the rotor shafts are always in a horizontal plane (see
figures to the right) and the flow of the fluid is in the direction
of the arrow marked on the body.
The pipe must be filled with liquid and free from air bubbles.
Avoid air purge of the system which would cause damages and
to prevent damage from dirt or foreign matter, we strongly rec-
ommend the installation of a 250 m strainer as close as pos-
sible to the inlet side of the meter.
When fluid passes through the fitting, rotors turn. This rotation produces
a measuring frequency in the associated hall sensor, which is proportional
to the flow.
Correct
Incorrect
7
!
2
.
)
.
'

Ö
$
/
Ö
.
/
4

2
%
-
/
6
%

4
(
)
3

#
/
&
,
/
7
Correct
Dimensions [mm]
!
"$
#
%
!
"$
#
%
'
&(
*+
ÖÖÖ
!.3)Ö&LANGEÖBOTHÖENDS
,
$).Ö&LANGEÖBOTHÖENDS
Orifice
DN
AB CDE
Stainless steel Aluminium
15 96 100 100 61 20 55
25 112 143 133 91 35 85
40 144 124 124 120 45 112
50 178 210 210 150 55 140
80 220 260 302 212 77 202
Orifice
DN
AB B CDE F GHJ KL
Stainless Steel Al.
DIN ANSI DIN ANSI
25 112 291 294 281 284 91 35 115 16 108 16.0 1.6 1.6 85
40 144 262 270 262 270 120 45 150 16 127 17.5 1.6 1.6 112
50 178 264 264 264 264 150 55 165 18 152 19.0 1.6 1.6 140
80 220 344 348 436 436 212 77 200 22 191 22.5 1.6 1.6 202
100 291 382 390 578 578 230 108 220 22 229 22.5 1.6 1.6 234
Threaded connection
Flanged connection

S070
p. 3/4
Ordering chart for sensor fitting Type S070
Orifice DN Process connection
Flow Range
Body material Rotor material Seal Item no.
> 5 cps < 5 cps
15 G ½” 2 - 30 l/min 3 - 25 l/min Aluminium PPS FKM 443 985
Stainless steel Stainless steel FEP/PTFE 443 990
NPT ½” 2 - 30 l/min 3 - 25 l/min Aluminium PPS FKM 443 995
Stainless steel Stainless steel FEP/PTFE 444 000
25 G 1” 6 - 120 l/min 10 - 100 l/min Aluminium PPS FKM 443 986
Stainless steel Stainless steel FEP/PTFE 443 991
NPT 1” 6 - 120 l/min 10 - 100 l/min Aluminium PPS FKM 443 996
Stainless steel Stainless steel FEP/PTFE 444 001
25 mm DIN PN16 flange 6 - 120 l/min 10 - 100 l/min Aluminium PPS FKM 553 637
Stainless steel Stainless steel FEP/PTFE 553 634
1” ANSI 150 LB flange 6 - 120 l/min 10 - 100 l/min Aluminium PPS FKM 553 636
Stainless steel Stainless steel FEP/PTFE 553 633
40 G 1½” 10 - 250 l/min 15 - 235 l/min Aluminium PPS FKM 443 987
Stainless steel Stainless steel FEP/PTFE 443 992
NPT 1½” 10 - 250 l/min 15 - 235 l/min Aluminium PPS FKM 443 997
Stainless steel Stainless steel FEP/PTFE 444 002
40 mm DIN PN16 flange 10 - 250 l/min 15 - 235 l/min Aluminium PPS FKM 443 988
Stainless steel Stainless steel FEP/PTFE 443 993
1 1/2” ANSI 150 LB flange 10 - 250 l/min 15 - 235 l/min Aluminium PPS FKM 443 998
Stainless steel Stainless steel FEP/PTFE 444 003
50 G 2” 15 - 350 l/min 30 - 300 l/min Aluminium PPS FKM 553 640
NPT 2” 15 - 350 l/min 30 - 300 l/min Aluminium PPS FKM 553 641
50 mm DIN PN16 flange 15 - 350 l/min 30 - 300 l/min Aluminium PPS FKM 443 989
Stainless steel Stainless steel FEP/PTFE 443 994
2” ANSI 150 LB flange 15 - 350 l/min 30 - 300 l/min Aluminium PPS FKM 443 999
Stainless steel Stainless steel FEP/PTFE 444 004
80 G 3” 20 - 733 l/min 66 - 616 l/min Aluminium Aluminium FKM 553 642
NPT 3” 20 - 733 l/min 66 - 616 l/min Aluminium Aluminium FKM 553 643
80 mm DIN PN16 flange 20 - 733 l/min 66 - 616 l/min Aluminium Aluminium FKM 553 645
3” ANSI 150 LB flange 20 - 733 l/min 66 - 616 l/min Aluminium Aluminium FKM 553 644
100 100 mm DIN PN16 flange 120 - 1200 l/min --- Aluminium Aluminium FKM 553 647
4” ANSI 150 LB flange 120 - 1200 l/min --- Aluminium Aluminium FKM 553 646
Ordering chart for spare parts for sensor fitting S070
Description
Orifice Size
Materials Item no.
[mm] [inch]
Rotor DN15 ½” PPS 550 933
Stainless steel 550 934
DN25 1” PPS 550 937
Stainless steel 550 938
DN40 1 ½” PPS 550 941
Stainless steel 550 942
DN50 2” PPS 550 945
Stainless steel 550 946
Description
Orifice Size
Materials Item no.
[mm] [inch]
O-ring DN15 ½” FEP/PTFE 550 929
FKM 550 930
DN25 1” FEP/PTFE 550 935
FKM 550 936
DN40 1 ½” FEP/PTFE 550 939
FKM 550 940
DN50 2” FEP/PTFE 550 943
FKM 550 944

S070
p. 4/4
Transmitter/Controller
remote version
Compact transmitterFitting with oval rotor
* Use only version with Hall transducer
Interconnection possibilities with other Bürkert products
Type S070
INLINE sensor fitting
Type SE35*
Flow transmitter/
batch controller
Type SE32*
Flow switch/
transmitter
Type 8025
Flow transmitter/
batch controller
Type 8032
Flow switch/transmitter
Intrinsic
safety
barrier
Type SE30*
Flow transmitter
Type SE30 Ex -
Flow transmitter
To find your nearest Bürkert office, click on the orange box www.burkert.com
In case of special application conditions,
please consult for advice.
Subject to alteration.
© Christian Bürkert GmbH & Co. KG 1605/8_EU-en_00891837
Type SE36
Flow transmitter