Burtonsafes Keyguard Combi User manual

Please note that all Keyguard safes are supplied with the
preset default code of [0][0][0][0].
To open your Keyguard Combi for the rst time you should
replicate the following steps:
• Rotate the four combination dials so
that the [0] digit on each dial is lined
up beneath the red arrow.
• Firmly hold the facia of your Keyguard
Combi and simultaneously slide the
silver catch down wards.
• With the silver catch still pushed
downward pull the facia away from the safe body.
KEYGUARD COMBI
LOCK MODEL: KEYGUARD COMBI GETTING STARTED:
SETTING YOUR OWN CODE:
Facts about the Keyguard Combi
• Place the facia of your Keyguard Combi face down on
a rm surface.
• Decide upon your new personal 4-digit code. (It is
very important that you remember this combination.)
• To set your code you rst need to rst ensure that the
four combination dials are rotated so that the [0] digit
on each dial is lined up beneath the red arrow.
• Slide the ‘code change pin’on the back of the facia
downward and to the right.
• Turn over the facia so that you are looking at the front
of it. Now turn each of the four dials so that your
personal 4-digit code (Read from top to bottom) is
lined up beneath the red arrow.
• Turn over the facia so that you are looking at the back
of it. Return the ‘code change pin’ on the back of the
facia to its normal position by sliding it to the left and
then upward.
• Once you have input your code you should check that
it has been correctly set. It is vital that you rst check
this with the Keyguard Combi open.
DO NOT YET REPLACE THE FACIA!
USER INSTRUCTIONS
Burton Safes Limited Unit 12 Brockholes Business Park, Rock Mill Road, Brockholes, Holmfirth HD9 7BN. t 01484 663388 f 01484 666338 [email protected] www.keyguardsecurity.co.uk
Pg. 1
KG-Inst-010
July 2013
= HOLD
0
0
= PRESS
0
0= DOUBLE BEEP = SINGLE BEEP = LED FLASHES TWICE = LED STAYS ON
KEY SYMBOLS = LONG BEEP
= I-BUTTON
0 9 1
0 9 1
0
9 1
0
9 1

USER INSTRUCTIONS
Burton Safes Limited Unit 12 Brockholes Business Park, Rock Mill Road, Brockholes, Holmfirth HD9 7BN. t 01484 663 388 f 01484 666 338 [email protected] www.burtonsafes.co.uk
CHECKING YOUR CODE:
• Rotate the four combination dials so that your personal 4-digit user code is lined
up beneath the red arrow.
• Firmly hold the facia of your Keyguard Combi and simultaneously slide the silver
catch downwards. If your code was correctly input then the catch will release into
the open position.
• You can also check that the Keyguard Combi will not now open on any other code.
Simply scramble the four combination dials and then try and slide the silver catch
downward. You should nd that the catch will not release.
REPLACING THE FACIA:
• Rotate the four combination dials so that your personal 4-digit user code is lined up beneath the red arrow.
• Firmly hold the facia of your Keyguard Combi and slide the silver catch downwards.
• Push the facia forward into position and release the silver catch. The Keyguard should now be shut.
LOCKING YOUR KEYGUARD COMBI:
Once you have replaced the facia, using the instructions above, it is vital that you
lock the unit:
• Replace the facia as described above.
• Now scramble the four combinations dials so that the numbers lined up beneath
the red arrow are dierent from your personal 4-digit user code.
• Check that your Keyguard Combi is locked by simply trying to slide the silver catch
downward. You should nd that the catch will not release.
CHANGING YOUR CODE:
You may wish at some stage to alter the personal code you have set. You can change
your code by following the steps below.
• In the usual manner open your Keyguard Combi and remove the facia.
• Follow the instructions as detailed in the section marked ‘Setting your own code’.
However when changing a code, the instruction under the fth step should now be to
rotate the four combination dials so that your personal 4-digit user code is displayed.
• Carefully repeat all the steps in the section marked ‘Checking your code’.
Pg. 2
5 4 6
8 7 9
2 1 3
3
2 4
2 1 3
1 0 2
9 8 0
4
3 5
8 7 9
3 2 4
5 4 6
6
5 7
Pg. 2BS-Inst-010 - July 2013

USER INSTRUCTIONS
Burton Safes Limited Unit 12 Brockholes Business Park, Rock Mill Road, Brockholes, Holmfirth HD9 7BN. t 01484 663 388 f 01484 666 338 [email protected] www.burtonsafes.co.uk
FITTING YOUR KEYGUARD:
To t your Keyguard you will need the following tools:
1 x Power Drill 1 x 5mm Masonry Drill Bit
1 x Cross Headed Screwdriver 1 x Lightweight Hammer
1 x Black Permanent Marker
• The diagram to the right shows an external view of the rear of your Keyguard
Combi, with the four xing holes highlighted in red for your reference.
Four appropriate xing screws have been supplied and it is recommended
that you use all of them.
• Locate a sound piece of masonry or brickwork in the area where you wish
to x your Keyguard Combi. It is suggested that you choose a site that is
accessible yet one that is not too prominent.
• Remove the facia from your Keyguard Combi and position the body rmly
against the wall and hold in place. Use the pen to make marks on the wall through the highlighted xing holes.
• Attach the 5mm bit to the power drill. Carefully drill a hole at each of the marked xing points; each hole should
be 60mm deep.
• Position the Keyguard so that the xing holes are aligned with the drilled cavities. By hand push the rst screw
and rawl cover into position. Repeat this with the three remaining xings.
• Locate the cross head of your screwdriver into the cross on your rst xing. Using the hammer gently tap the screw
and rawl cover into the drilled cavity so that the rawl cover is fully inside the wall. Repeat this step with the three
remaining screws.
• Finally use the screwdriver to fully tighten all four xings into position. You should nd your Keyguard Combi is
rmly secured in position.
Pg. 3BS-Inst-010 - July 2013