Burtonsafes Keyguard DigitalXL User manual

INSTRUCTIONS
To fit your Keyguard XL you
will need the following tools:
• Power Drill
• 5mm Masonry Drill Bit
• Small Socket Driver
• 8mm Socket Head
• Marker Pen
NOTE: Your Keyguard XL
should be fitted to a solid
surface. We recommend
brickwork, stone or concrete
• To start use the rubber
cover as your template to
mark the fixing holes on the
wall. Ensure you choose a
location that allows the best
possible fixing e.g. the centre
of a brick. N.B. You must
never fix into the mortar
• Push the bolts that have
been supplied with your
Keyguard XL into each of
the holes
• Tighten each bolt fully using
a socket set
• Now use the 5mm drill bit
to make a hole 55mm deep in
each of the marked fixing holes
• Place the Keyguard XL
inside the rubber case
• Open the door of your
Keyguard XL and place the
whole unit onto the wall lining
up the holes
Tools
Fixing holes
FITTING YOUR KEYGUARD
Place
5 mm
TROUBLESHOOTING
• Once the fitting is complete
if the door closes but does
not lock, test locking it when
the door is in the open
positon. If it works, it is likely
that the fixing bolts are
protruding too far into the
Keyguard XL. Try to secure
them further into the wall and
close the door again
• If the buttons will not press,
ensure that the dial is in the
vertical position
• If your code does not work,
press the “clear” button and
start again
• Fixing kit - anchor bolt
• Fixing kit - concrete screw
with pan head
• Fixing kit - concrete screw
75 mm (for rendered walls)
• Fixing kit - concrete screw
100 mm (for rendered walls)
If you require the fitting
instructions for any of the
above please visit the website
or call our office during office
hours on 01484 663388 for
further assistance.
www.burtonsafes.co.uk/products/
keyguard-digital-xl/
1
2
3
4
5
6
7
8
9
0
A B
Vertical Position
Burton Safes offer a range of fixing
bolts to suit different applications
that retain the security
specification:
Clear Button
Instruction booklet
Standard fixing bolts
In the event of a product
malfunction please contact
Burton Safes Ltd
Burton Safes Ltd. Brockholes
Holmfirth HD9 7BN
Tel: [phone]
!
02/01/2022 V.1 Page 2 of 2

INSTRUCTIONS
LOCKING YOUR KEYGUARD
NORMALLY
OPENING YOUR KEYGUARD
NORMALLY
CHECKING YOUR CODE
• Remove unit from the box
and place it on it’s back
• Pull the rubber cover open
• Make sure that the dial is in
the vertical position
• Press and slide the “clear”
button (the ridged black
button pictured below) down
• Release the clear button
SETTING YOUR CODE
• With the door open, turn the
dial anti-clockwise, until it clicks
• Make sure the locking bar is
in the locked position
• Stand the Keyguard XL
upright, keeping the door open
• Using a phillips screwdriver,
remove the screw securing the
black plastic plate
• Choose a personal code
which must be between 3 and
8 digits. NOTE: You may only
use each number/letter once
• Using a flat head screwdriver,
rotate each button in your code
180 degrees, so that the arrow
on each one faces the SET
position
• Re-secure the black plastic
plate with the small screw,
make sure you leave the door
open to check your code
02/01/2022 V.1 Page 1 of 2
• Ensure that the dial is in the
vertical position (shown in the
image below)
• Enter your code
• If you enter your code
wrong, press and slide the
“clear” button down and then
release the button. You can
now re-type your code
• Rotate the dial clockwise
360 degrees, until it clicks
• Pull the door open
• Close the door and lock it
by turning the dial
anti-clockwise 360 degrees.
It should click at least once
• Ensure that it has locked
properly by turning the dial
clockwise 360 degrees until it
clicks. Try and open the door, if
it does not open your Keyguard
XL is now fully secure
• Close the lid of the rubber
cover
TROUBLE SHOOTING
• The dial must be in the
vertical position to use the
code buttons
• If your code hasn’t worked,
ensure you press the “clear”
button before entering the
code again
• Ensure that the arrow on the
dial of each button is in the
“set” positon when setting
your code
• Ensure that all numbers not
in your code have their dials
facing the “not set” positon
• Ensure that the black plastic
plate is properly and securely
refastened
• You may find that when you
turn the dial you feel some
resistance, do not worry, this
is normal.
• Make sure the dial is in the
vertical position
• Press and slide the clear
button down and then release
the button
• Use the keypad to input
your chosen code
• Turn the dial clockwise until
it clicks
• If it opens, Keyguard XL is
ready to use
• With the door still open,
make sure the Keyguard XL is
locked by rotating the dial
anti-clockwise 360 degrees,
until it clicks
CHANGING YOUR CODE
• Open your Keyguard XL
as normal
• Remove the screw securing
the black plastic plate with a
small phillips screwdriver
• You will need to turn the
disk of each number in your
previous code until the arrow
faces the NOT SET position
• You can now repeat All of
the steps in the section
marked ‘SETTING YOUR
CODE’ and ‘CHECKING YOUR
CODE’
• Turn the dial clockwise 360
degrees, until it clicks
• Pull the door open
Vertical Position
Clear Button
Clear Button
Clear Button
Vertical Position
Vertical Position
Vertical Position
DialClear ButtonRubber Cover
Not Set
Plate
Screw
Locked position
Locking Bar
Set
1 2 3 4 5 6 7 8 9 0 A B
1234567890A B
1 2 3 4 5 6 7 8 9 0 A B
OPENING YOUR KEYGUARD
XL FOR THE FIRST TIME
Screw removedUse screwdriver
!
!
Set
Not Set
Not Set
1
2
3
4
5
6
7
8
9
0
AB
360°
Click
360°
Click
Click
360°
Click
360°
Click