BURY CC 9058 Instruction manual

CC 9048 / CC 9058
QUICK USER GUIDE

Installation of the hands-free car kit
Scope of supply
CC 9048
8
Dear customer,
Congratulations on purchasing a BURY hands-free car kit. You have chosen a high quality product that is
extremely easy to use.

CC 9058
8

Installation of the hands-free car kit
Scope of delivery:
1. Electronic box
2. Illuminated remote control / Multifunction
display with cradle and mount, screws for the
holder and rubber cover, adhesive tape
3. Microphone
4. ISO cable harness
5. Extension cord
6. AUX-In cable
7. Micro USB charging cable
8. Quick user guide

Connections on the electronics box:
1Mini-USB
2 Power supply/muting using Mute via
ISO cable tree
3Microphone
4 LINE-IN
5Multifunctiondisplay
6 RJ45-remote control

Installation of the system
123 4

Installation of the hands-free car kit
123
456

Step 1:
Pull the ISO jacks at the back of the radio off and replace them with the jacks at the ISO cable harness. Connect
the now free ISO jacks with both sockets from the ISO cable harness (see picture).
If you want music or voice signals to be fed via the four LINE cables, you must adjust them accordingly to the
respective type of radio and its connections (PHONE-IN or AUX-IN). Appropriate adapters are available from
specialists shops.
Step 2:
The hands-free car kit supports the radio mute function, if this function is also supported by the radio. The mute
signal is then fed to the radio via the yellow cable of the ISO cable harness. The cable is labelled with “mute”
and must be connected to one of the three sockets (mute1, mute2, mute3). Please observe the notes on this
topic in the instruction manual of the radio concerning “Pin allocation for mute / radio mute”. Then, connect the
mute cable to the corresponding socket.
Step 3:
Insert the 24-pole molex jack (A) into the connection of the electronic box (see picture).
Connection diagram for ISO cable harness
PWR/LSP/LINE OUT

Installation of the hands-free car kit

- 12V Power
- 12/24V Ignition
- Ground
- Line-out 1 - Line-out 2
1-Line L + / Phone L + 1-Line R + / Phone R +
2-Line L - / Phone L - 2-Line R - / Phone R -

Installation of the hands-free car kit
- Micro Molex 24 - ISO - connection to the electronic box (HFCK)
- connection to the vehicle’s speakers
- connection to the vehicle’s power supply
- connection to the car radio
- connection to the car radio
1 - Mute 3
2 - Mute 2
3 - Mute 1
4 - Ignition
5 - Antenna
6 - Illumination
7 - Power
8 - Ground
1 - C RR-
2 - C RF-
3 - C LF-
4 - C LR-
5 - R LR-
6 - R LF-
7 - R RF-
8 - R RR-
9 - LINE R+
10 - LINE L+
11 - R-Mute
12 - Ground
13 - C RR+
14 - C RF+
15 - C LF+
16 - C LR+
17 - R LR+
18 - R LF+
19 - R RF+
20 - R RR+
21 - LINE R-
22 - LINE L-
23 - Ignition
24 - Power

Operating guideline
Establishing a
Bluetooth connection
123
456
79
*
#
PIN: 1234
„CC 9048 ...“
„CC 9058“

Operating guidelines CC 9048
Language selection
After properly connecting the HFCK to the power supply, the device will start with the launch of the car
ignition. To use voice prompts, activate them by pressing and holding the Plus button for 10 seconds.
Then select the language for voice prompts after the device informs about it by emitting „Choose lan-
guage“. Available languages will be read out (English, German, French, Spanish, Russian, Polish, Czech
and Dutch), a single press of the middle button during wanted language presentation confirms the choice.
The list of available languages will be read three times, in the absence of selection, English will be loaded
automatically.
To change the language selection, restore the factory settings by holding the Minus button for 10 sec-
onds. The device will reset, then the voice prompts have to be activated and the system will repeat the
procedure of language selection from the beginning.
To turn off the voice prompts just press and hold the Plus button for 10 seconds.

CC 9048
Status Status
description Press Plus
key once Press Minus key once Press Middle
key once
Hold Middle
key for
2 seconds
Press Middle
key twice
Hold Plus and
Minus key for
4 seconds
Hold Plus
key for
10 seconds
Hold Minus
key for
10 seconds
Hold Plus
and Middle
key for
4 seconds
Hold Minu
s
and Middl
e
key for
4 seconds
Stand-by When HFCK is not connected
with phone Volume up Volume
down Auto connect on/off
Multipoint
on/off
(1 beep is off,
2 beeps is on)
-
Audio option
(1 beep,
2 beeps,
4 beeps)
Voice Prompts
on/off
(1 beep is off,
2 beeps is on)
Factory
reset
AUX-In
on/off
(1 beep is off,
2 beeps is on)
Mobile audio
on/off
(1 beep is of
f,
2 beeps is on
)
Language
selection After factory reset --
Choose current
language -- -----
Connected
When HFCK
is connected
with phone
(or two phones)
Volume up Volume
down Calls phone voice tags
Disconnect
HFCK and
phone (phones) Redial
Turn on/off DSP*
in the phone
(1 beep is off,
2 beeps is on)
--
AUX-In
on/off
(1 beep is off,
2 beeps is on)
Mobile audio
on/off
(1 beep is of
f,
2 beeps is on
)
Incoming
call Volume up Volume down Accept call Rejects call - - - - - -
Incoming
call
When HFCK
is connected
with phones
and call
is active
(Multipoint)
Volume up Volume
down
End first call
and make
incoming call
active on device
Reject
second call ------
Active call Volume up Volume
down Quit call
Change car kit
mode to privat
mode or privat
mode to car kit
mode
Mute micro-
phone of HFCK
(function is
active if DSP
in the HFCK
is active)
Turn on/off DSP
in the HFCK
(1 beep is off,
2 beeps is on)
--- -
* depending on mobile phone
Overview of the key functions

Operating guidelines CC 9058
Handling via Touch screen
The operation can be carried out via the keys. With the end call button you can cancel an action or go
a step back. If you press down the middle button you will return to the main menu. With the call but-
ton you can confirm actions. Use the horizontal buttons to navigate around the menus.
Look through our comprehensive collection of bluetooth car kits right away.