BURY RC 9060 User manual

Index
Introductory information 2
1. General 2
2. Security guidelines 2
Installation of the hands-free car kit 4
3. Scope of supply RC 9060 4
4. Positioning of the 3-button remote control 4
5. Connecting the Electronic box 6
6. Installation instructions for the fuses 7
7. Installation instructions switching box AC 5120 8
Operating guidelines 12
8. Initial operation of the hands free car kit 12
9. Handling possibilities 12
10. Establishing a Bluetooth®connection 13
11. Accepting, making, ending calls 15
12. Voice Dial 15
13. Voice dial commands 17
14. Head menu 18
15. Dial number 18
16. Phone book 19
17. Redial 21
18. Call lists 21
19. Messages 21
20. Dial Joe Bloggs 21
21. Settings 22
21.1 Bluetooth®22
21.2 Voice Dial 22
21.3 Audio 23
21.4 Device 24
22. 3-Button Remote Control 25
23. Play music with A2DP 26
Further Information 27
24. Service 27
RC 9060

2Introductory information
1. General
Dear customer,
Congratulation on purchasing a BURY hands-free car kit. You have cho-
sen a high quality product that is extremely easy to use. All aspects of
BURY production through to sales and service are subject to strict qua-
lity management according to DIN EN ISO 9001. All BURY hands-free
car kits meet CE and e1 security standards. Furthermore, we provide a
two-year warranty on all components.
Please read the operating manual carefully so that you can fully enjoy
your BURY hands-free car kit. If you have any further questions concer-
ning installation or operation of your car kit, please contact your dealer.
He will be happy to give you reliable advice. You can also contact our
hotline. Our phone and fax numbers are listed in the chapter Service at
the end of the operating instructions.
Have a good trip!
2. Security guidelines
Installation – who and where
The installation of this system can be carried out by yourself but please
observe the installation requirements of the automotive manufacturer
(VAS 1978). During the installation, park the car at a place where the
road traffic is not impaired. We recommend to let a specialised work-
shop perform the installation.
Power supply
This system has been designed for the use in vehicles with an on-board
supply system of 12 volts (passenger car). If you intend to install the
device in a vehicle with an on-board supply system of 24 volts (lorry),
please use a voltage converter. If you have queries regarding this sub-
ject, please contact our hotline.

3
Position, volume
Install the components of the device in the vehicle so that your field of
vision is not impaired and the components are not mounted in the im-
pact zone of the passenger compartment or in the airbag inflation
zones. The removal of coverings (with and without airbags) or compo-
nents of the dashboard requires – in some cases – special tools and
special knowledge.
Intended use
We shall not be liable for damages or malfunctions due to improper use
of the navigation system. Therefore, do not expose the device to
moisture, extreme temperatures or shocks and carefully follow the pro-
cedure described in the installation and operating guidelines.
Use while driving
Operate the system only when the situation allows it and when you do
not endanger, harm, constrain, or annoy other road users. The volume
of the device has to be set in a way that exterior noise is still audible.
Faults
Do not commission the device if you detect or assume a defect. In this
case, contact a BURY specialised dealer or our hotline. Improper repair
efforts can be dangerous for you. Therefore, only skilled personnel may
perform inspections.
Important:
The driver is ultimately responsible for the safe operation
and control of their vehicle at all times. You should never
use a hand held phone, including sending or reading text or
picture messages, while driving.
Research indicates that there is a risk to safety when the
driver of a motor vehicle is distracted and using a mobile
phone while driving can be a distriction.
The manufacturer strongly recommends that you use a
hands-free solution when driving.

4
3. Scope of supply RC 9060
4. Positioning of the 3-button remote control
Step 1:
First of all, choose the most suitable location for the 3-button remote control by positioning it or hol-
ding it at different locations in the vehicle yourself. Once you have found a suitable position for the
remote control, you can attach it / mount it appropriately. Please use the cleaning cloth provided to
remove any grease or dirt from the surfaces. Please remember that in the event of strong temperature
variations, depending on the structure and quality, the colours of the surfaces may fade during subse-
quent use.
Important:
The remote control can only be stuck down once. Damage to its adhesive surface may
occur when it is removed.
Installation of the hands-free car kit
Description of the components:
1) Electronics box
2) Remote control
3) Hook-and-loop fastener
4) Fixing screws for electronics box
5) Microphone with cable
6) Loudspeaker switching box AC 5120

5
Step 2:
Depending on the vehicle type and its equipment (e.g. airbags), it is
reasonable to install the microphone either at the A-pillar, at the sun
shield or at the roof interior. For details about the equipment features
please refer to the vehicle documents. Please also observe the notes on
distances to other components and to the driver / speaker, as specified
in the installation manual.
Step 3:
Please lay the cables in a way that they do not lie/hang unsecured in
the vehicle and that they may not influence the conducting of the vehi-
cle. When laying a cable, please take care that it is not under traction
stress but that it has some tolerance. Avoid crushing the cable as da-
mages of the insulation can be caused by friction/rubbing.
Step 4:
Install the electronics box at a convenient place in the vehicle. This can
e.g. be behind the radio, in the glove box, or in the centre console.
Please mind that you can access the connections of the box without
difficulty. Before connecting the components to the electronics box you
should branch off the battery for safety reasons. In doing so, take into
account that there might be a radio coding (confer radio manual).
Important:
Please install the electronics box behind a cover or so-
mewhere you can only reach by opening or unfastening a
protective cover/ a cover. The terminal box must not hang
loosely in the vehicle..

6Installation of the hands free car kit
5. Connecting the Electronic box
Please connect the switch box AC 5120 to the electricity supply of the
radio and connect the Molex plug with the electronic box (see chapter:
Connection of the loud speaker switch box AC 5120).
Now connect the 3-button remote control (connection 3) and the micro-
phone (connection 5) to the electronics box.
Through connection 4 the hands free set passes on the voice of the
dialogue partner during the telephone call. You can connect a separate
loud speaker (BURY accessories) or the AC 5120 to this connection.
With the latter variation, you use the vehicle’s internal sound system for
a voice return.
Note:
If the DIN ISO plug of the AC 5120 does not fit in your
vehicle, numerous adapters are available from dealers.
Stereo quality music is emitted at connection point 2. You can also
connect the AUX In input of your radio here (if you have one) using an
adaptor available from specialist dealers. To be used with the hands-
free device, the adaptor must have a 3.5mm stereo jack plug. The
connection at the other end will depend on the type of car radio. If your
radio does not have an AUX In, you can use the Car CD/MP3 adaptor
from the BURY accessories range in order to listen to music on your
radio.
1
2
3
4
567
Connection Options:
1 Power supply
2 AUX-out (without function)
3 3-button remote control
4 external loudspeakers
5 Microphone
6 Connection for display (optional)
7 System 9

7
6. Installation instructions for the fuses
Please cut through the red, the black and the blue cable by means of a wire cutter or scissors. Now
insert the two endings of the red cable resulting from the cut into one of the binders, then close it. If
you hear two clicking noises, the clamp snapped in properly. Now insert one of the fuses and then
repeat the procedure with the other cables.
If you install the RC 9060 without the switchbox AC 5120 please stick to the following instructions
regarding the power supply safety.

8Installation of the hands free car kit
7. Installation instructions switching box AC 5120
With the AC 5120 speaker switchbox, you get the possibility of being able to mute the feedback of your
car radio / CD player etc. and to transfer the voice output of your conversation partner during a tele-
phone call to your vehicle’s speakers. This means that the installation of additional speakers isn‘t re-
quired. If your radio has a mute function, then the vehicle speakers are turned onto mute using the
radio. If your car radio doesn‘t have this function, then the signals will be suppressed by the speaker
switchbox. You can use the AC 5120 through the connections that your BURY hands free car kit offers,
which guarantee voltage supply via molex plugs and also have a speaker output.
If you want to make a telephone call in the hands-free mode, your car radio will be automatically swit-
ched on to mute (for the exact operation of your hands free car kit, please read your HFCK user ma-
nual). The Audio switchbox now uses one or two loudspeakers in your car for the telephone conversa-
tion, even if your radio is switched off. This function will be automatically activated after the installati-
on of the unit, there are no subsequent manual settings required.
Some mobile phones do not support a radio mute function. Please read your telephone user manual
for more details. You can find out more detailed information at your specialist retailer, in the internet
under www.bury.com, or over our telephone hotline.

9
After checking that all the cable lengths are sufficient, decide where you are able to attach the Audio
switchbox. Now secure the Audio switchbox so that it isn’t able to flap about and/or rattle against other
parts of your vehicle.
Now connect the audio switchbox plug (1) to the hands-free car kit. (The other, smaller box is used by
the audio switchbox plug for the microphone.) Now connect the white power out cable connector (2)
of your Audio switchbox to the power supply socket of your hands-free kit.
Now disconnect the (a) and/or the (b) loudspeaker connector from the speaker socket on the radio at
the back. Connect this connector with the suitable socket (3) on the AC 5120. Now connect the plug
(4) with the radio.
Depending on the switcher position (5), the voice of your conversation partner will be fed back through
either the front right speaker, the front left speaker, or through both of the front loudspeakers. The
‘OFF’ position is to be selected if you connect the switchbox to the radio using the ‘Phone-IN’ cable
(6).
1
2
6

10 Installation of the hands free car kit
The two ‘Phone-In’ cables are marked accordingly and must be plugged into the appropriate con-
nections on the radio (blue, green or yellow). In this regard, please refer to the instructions
concerning the connection configuration of your car radio in your car radio handbook. In lots of
radios, the volume level (feedback of your conversation partner) can be controlled via the phone
input and the selection of the loudspeaker.
Different connections of the ISO plug on the radio
The layout of the pins on the ISO plug used in a car depends on the type of car. Before using the
switchbox, you should make sure that the connections are correct in order to prevent possible
damage to the device.
Configuration I
If the assignment of pin 7 of the ISO plug is connected to the DC Power Supply, and pin 4 is
connected to the ignition, you should check if the connection looks like the connection presented
on the drawing below.
Switchbox Vehicle
red 7 (red)
blue 4 (blue)