CABINETS TO GO Findley & Myers LC1884 User manual

Page 1
PantryCabinet 
ASSEMBLY INSTRUCTIONS
Theseassemblyinstructionsare onlyapplicableforPantryCabinets.
ITEM#LC1884,LC1890,LC1896,LC2484,LC2490,LC2496,LC3084,LC3090,LC3096, 
UC1284,UC1290,UC1296

Page 2
►Items Quantity
►General Instructions:
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT
1-800-CABINET.
►Required tools:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
►Hardware Box:
a
b
Qty 6-12 Qty 12-16
A
A
B
DB
C
F
Item Description Qty
AFaceFramewithDoor1
BSidePanels(left & right)2
CTop, Bottom, and Center Panels3
D
EBack Panel 1
FShelves(84"&90"tall3pcs,96"tall4pcs) 3or4
GToe Kick 1
HardwareBox:1
ShelfClips:84"&90"tall12pcs,96"tall16pcs, rubber bumpers 6-12pcs
C
E
C
x3-4
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.

Page 3
IftheUCorLCyouareinstallingrunsthelengthofyourceilingheight,itis
recommendedtoassembletheunitstandingtoavoidscrapingyourceiling.
►Instructions:
1.
Put the Back Panel (D) face up on a flat soft working surface to ensure that the surface is not scratched
or damaged (Figure 1).
2.
Installing the Side Panels: Insert the right and left side panels (B) into the grooves of the back panel
(D)andalign the camlockconnectors.(Figure2) Lockthe camlock witha screwdriverbyturning the screw 180°
clockwise. (Figure 3)
3. Installing the Toe Kick (F): Place the toe kick (F) at the end of side panels (B). Aligneachcamlockonthe
toekickandlockthem. (Figure 4)
4.
Install the Top, Bottom, & Center Panels (C)bysliding them in to the grooves.
5.
Install the face frame (A)byplacingcamlocksidedownontotheboxofthecabinet.(Figure 6) Align all
grooves and cam locks onto the face frame and coordinating cam locks. It may be necessary to open all
cabinet doors. Lock all face frame cam locks with a screwdriver. (Figure 3)
A
Figure6
6. Install the shelf clips (b) into the cabinet at the desired heights
for the adjustable shelves. Insert the shelves (E) into the
assembled cabinet. Install the rubber buttons (a) onto the corner
of the doors where they come in contact with the frame.
Figure 1
Figure 2
D
B
C
Figure 4
Figure
3
Figure 5
F
C
C
B
B
a
b
Qty 6-12
Qty 12-16
NOTICE

Page 4
1. Place the face frame (A) face downona flatsoftworking surfacetoensure thatthe
faceis not scratched or damaged. (Figure 1) .
2. InstalltheSidePanels(Figure2): Insertrightandleftsidepanels (B) intothegrooves of
thefaceframe (A) andalignthecamlock connectors (Figure2). Lockthe camwithascrewdriver
byturningthescrew180° clockwise (Figure4) .
3. InstalltheBottom and Microwave shelf(Figure3): Gently spreadtheside panels (B)and
insert (C) & (D) intothegroovesofsidepanels (B) untilthey areseated in theface frame (A).
4. Installing theBack PanelandToeKick (Figure5): Beforeyoustartthisstep,putthe
backpanel (E) onaflatsurfacefacingupward.Installthedrawer slide supports (f) inthepre‐
spottedareaonthebackpanel (Figure6). Thebottom of the slide supports should be facing
the bottom groove.Securethemwith2screws each (e)( Figure6).
Theninstallthe backpanel (E)
to the rearofsidepanels (B)(Figure5) .Alignandlockeachcamlock.InstalltheToeKick (F) by
lockin
► Maintenance
For daily cleaning, use a dry cloth
and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other
products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.