Canon Creative Park Ships of the world Esmeralda User manual

Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold.
Valley fold(dashed and dotted line)
Make a valley fold.
Scissors line(solid line)
Cut along the line.
Cut in line(solid line)
Cut along the line.
Glue spot(Red dot)
Glue parts with the same number together.
Glue spot(Green dot)
Glue within the same part.
Glue spot(Blue dot)
Glue to the rear of the other part.
Glue
The glue spot(colored dot)
shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
View of completed model
Assembly Instructions : Six A4 sheets (No. 1 to No. 6)
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.
* This model was designed for Papercraft and may differ from the original in some respects.
Before starting assembly:
Writing the number of each section on its back side before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after cutting out the sections.)
The parts used will vary somewhat, depending on whether the completed vessel will be modeled to depict
a ship facing wind from the left (with the bow pointed to the right) or from the right (with the bow pointed to
the left). First decide where you want to display the completed vessel, then decide whether the bow should
point to the left or right.
Bow pointed to the right (A - standard parts)
Bow pointed to the left (B - optional parts)
Indicates sections that should be glued first,
then cut out.
Indicates sections that should be folded once,
then unfolded.
After folding the part once and gluing the two
folds together, cut out from the yellow area.
Glue parts 2 and 3 together in
the same way.
Indicates where sections should
be glued together.
Indicates where to insert sections.
Do not glue the sections together.
©Canon Inc. ©M. Nishiguchi/SENAUN
Ships of the world : Esmeralda : Assembly Instructions
http://www.canon.com/c-park/

©Canon Inc. ©M. Nishiguchi/SENAUN
Ships of the world : Esmeralda : Assembly Instructions
(bow pointed to the right) or
(bow pointed to the left; optional part)
After folding this part, unfold and cut out
from the cream-colored area.
Apply glue to part 26 at the
spot shown in the illustration,
and then attach it to the mast.
Glue the glue spots of parts 11, 19,
and 26 to the bottom side of the deck.
Curl part 44 by wrapping it
around a thin stick
(such as a toothpick).
Insert until
the corners meet.
Glue the rear sides of
these parts together.

©Canon Inc. ©M. Nishiguchi/SENAUN
Ships of the world : Esmeralda : Assembly Instructions
Glue these parts
together.
Cut away the yellow area. Cut away
this area for part 29 in the same way.
Glue the glue spots of part 29
in place as shown by the arrows.
Glue the rear sides of these parts together.

©Canon Inc. ©M. Nishiguchi/SENAUN
Ships of the world : Esmeralda : Assembly Instructions
Glue part 36 in place after first
attaching part 35 to the hull.

©Canon Inc. ©M. Nishiguchi/SENAUN
Ships of the world : Esmeralda : Assembly Instructions
As shown in the illustration,
use A parts (standard parts) for
parts 45 - 48 when the bow will face
to the right and B parts (optional parts)
when the bow will face to the left.
For parts 66 - 69, choose A parts
(standard parts) or B parts (optional parts)
depending on the direction in which
the bow will point.
Surface A on top
(bow pointed to the right)
Surface B on top
(bow pointed to the left)
Attach parts 53 - 56 (the yards) to the vessel masts. If the bow will
point to the right, attach the yards so that surface A is on top. If
the bow will face to the left, attach so that surface B is on top.
Glue the yards in place at an angle, as shown in the illustration,
so that the model will resemble a ship sailing in the wind.
Fold once and glue the folds together,
then give the sails a bulging appearance.
If you plan to have the bow face to the right,
curl the sails so that surface A will bulge out.
If the bow will face to the left, curl the sails
so that surface B will bulge out.

©Canon Inc. ©M. Nishiguchi/SENAUN
Ships of the world : Esmeralda : Assembly Instructions
Chilean vessel
Esmeralda
Chilean vessel
Esmeralda
Chileanvessel
Esmeralda
Fold parts 72 - 75 (the square sails) in half and glue both folds together.
After curling these from top to bottom as shown in the illustration, make them curl
from the center to the outside, to make it appear as if they are catching the wind.
Glue the rear sides of
these parts together.
Finished!