Car Solutions QPI-G7-MAIN-V2.0 User manual

Update Date 2013.11.14
Model QPI-G7-MAIN-V2.0
Firmware Date 131028
Video Interface for
Volkswagen Golf 7
with Discover Media
User Guide
Car-Solutions.com
www.car-solutions.com [email protected]

Warning
When installing the main unit, do not remove or alter existing
vehicle fasteners, including nuts, bolts, screw, clips, and fittings.
Never detach, move or alter existing vehicle wiring, including
electrical grounds and straps. Alteration of existing vehicle
components may make vehicle unsafe to operate. Should be
no any electronic devices or magnetic pole around installation
place.
Air bags are vital part of a safety system. Never install main unit
in a way which will alter air bag wiring or interfere with air bag
deployment. Air bags must function properly in the event of an
accident.
Before installing, check the location of pipe, tank, electrical
cables and others.
Read and follow the instruction manual.
Wiring location must not interfere driving, get in or out from car.
Use electrical tape to insulate the ends of all wires, even if they
are not used. Proper insulation prevents arcs, shocks and fires.
When installation is complete, test all vehicle electrical systems
to ensure they operate correctly, including lights, horn, brake
lights, and emergency flashers.
According to our sales policy, any problems caused by user’s
mistake, careless can not be guaranteed.
Caution
All steps of installation should be done by well-trained specialist.
During installation ignition key should be taken off and after all
installation finish connect power cable with interface for the last
step.
Do not install the main unit in places where it ma be exposed to
dew condensation (around the air conditioning hose, etc), or in
locations where it may come in contact with water, high levels of
moisture, dust or oily smoke
Install wiring in a manner in which cables will not come in contact
with metal parts. The wiring may be damaged by contact with
metal parts, resulting in fire and shocks. Avoid all contact with hot
surfaces when wiring the main unit. High temperatures may
damage wiring, causing shorts, arcing and fires.
Kindly check all parts are in the box, when receiving the product, if
anything missing, inform to the supplier or manufacturer.
Warning / Caution
Car-Solutions.com
www.car-solutions.com
[email protected]

Table of Contents
1. Specifications
1.1 Main Specifications
1.2 Features
1.3 System Diagram
1.4 Components
1.5 Exterior
2. Installation
2.1 Installation Diagram
2.2 Installation
2.3 Connecting Can wires
3. Settings
3.1 DIP Switch
3.2 Remote Control
3.3 Car Model and Navi Model
3.4 Factory Mode
3.5 DVD, DTV IR-MEMORY input
3.6 Original Button Usage
3.7 Rear Camera
3.8 Rear Parking Guidelines
3.9 OSD
4. Trouble Shooting
1
2
3
4
5
6
7
8
10
11
12
13
16
17
18
19
20
22
Car-Solutions.com
www.car-solutions.com
[email protected]

1. Specifications
-1-
1.1 Main Specifications
1. Car Compatibility
VORKSWAGEN GOLF 7Generation 5.8” Monitor
2. Components
Interface* 1EA
3. MULTIMEDIA INTERFACE input specification
3 * A/V input (video external input)
1 * CVBS(Rear Camera) input
2 * Analog RGB input (Navigation system output)
1 * LCD input (Car system input)
4. MULTIMEDIA INTERFACE output specification
1 * LCD output
5. Power specification
Input power : 8VDC ~ 18VDC
Consumed power : 3.5WATT
6. Switch input mode
- External display skip function : through DIP switch, can
control each video input
- Through remote control, can change input mode
- Through CAN or rear lamp cable, rear camera can be
detected
Car-Solutions.com
www.car-solutions.com
[email protected]

1. Specifications
-2-
Easy installation through connection with commander
Able to adjust DVD, NAVI display on screen
Improved Screen Display (user-oriented interface)
Provide power cable to connect with rear camera
Dynamic PAS(Parking assistance system), moving parking
line according movement of steering wheel
1.2 Features
Car-Solutions.com
www.car-solutions.com
[email protected]

1. Specification
-3-
1.3 System Diagram
DISPLAY
A/V 1
NAVIGATION Input
(Analog RGB)
CVBS
(Rear camera)
Car Screen Input
(CAR MAIN BOARD)
A/V 2
A/V 3
VIDEO
CIRCUIT
VIDEO MUX
MCU
Power Input
(+8VDC ~ +18VDC)
POWER
CIRCUIT
Dip S/W
A/V OUT HEADREST
MONITOR
Remote control Switch for source toggle
Car Installation
OEM LCD
Rear Camera
Analog Input2
Car-Solutions.com
www.car-solutions.com
[email protected]

1. Specification
-4-
1.4 Components
A/V cable * 1EA
Mode cable * 1EA
IR cable * 1EA
R-CAM POWER cable * 1EA
(HARETC0002)
(HAVCAB0002)
Remote control * 1ea
(REMOTE0001)
(HARETC0001)
(HIRCAB0002)
LVDS OUT Cable * 1ea
(HLVDSC0003)
RGB cable * 1ea
(HRGBCA0013)
LCD Cable * 1ea
(HLCDCA0015)
Sub-board * 1ea
TOUCH Cable * 1ea
(HTOUCH0015)
POWER cable (12P) * 1EA
( HPOWER0043)
CAN IN/OUT cable * 1ea
(HARETC0076)
Car-Solutions.com
www.car-solutions.com
[email protected]

1. Specifications
-5-
1.5 Exterior
Dimension
Width 150.4mm
Length 99.4mm
Height 2.3.2mm
①MODE
②IR
③POWER
④REAR
⑤RGB-IN(HDMI)
⑥RGB-IN(NAVI)
⑦AV IN/OUT
⑧TO NAVI T/S-OUT UART
⑨LVDS OUT
⑪LED
⑩TEST
⑫DIP S/W
①⑥⑦
⑧
⑨⑩⑪⑫
②③④⑤
Car-Solutions.com
www.car-solutions.com
[email protected]

2. Installation
-6-
2.1 Installation Diagram
AV1 AV2 AV3
REAR C
Audio L
Audio R
AV/OUT Video
REAR (12V OUT)
GN D
Original
Monitor
Provided LVDS cable
Provided sub-board
Original LCD Cable COMMAND
provided LCD cable
B DATA (blue) SYNC GND
IR-DTV
NAVI-VS
IR-NAVI
IR-DVD
R DATA (red) G DATA (green)
REAR-C
SAFE
F-CAM-DET
CAN-L
CAN-H
ACC (12V ~24V)
GND
MMI
CAN-IN-H
CAN-IN-L
CAN-OUT-L
CAN-OUT-H
Car-Solutions.com
www.car-solutions.com
[email protected]

2. Installation
-7-
2.2 Installation
※After Dividing an original LCD Cable from the
Command, the the cable connect to provided
sub-board. And then provided LCD cable
connect to command
COMMAND
Provided LCD Cable
Provided LVDS Cable
Original
Monitor
Original LCD Cable
Car-Solutions.com
www.car-solutions.com
[email protected]