Car Solutions RGB-LE-V3.1 User manual

LAST UPDATED : 2014.02.04
model : RGB-LE-V3.1 / product code : RB-100126-013
INFINITY FX 35/45
+RGB-LE
Specification & Installation
Car-Solutions.com
[email protected]
www.car-solutions.com

2
2. Setup
2.1 DIP switch
2.2 Remote control
2.3 Power cable wiring diagram
7
8
9
3. Installation
10
11
Contents
1. Before installation
1.1 Main specification
1.2 System diagram
1.3 Components
1.4 Exterior
4
3
5
6
3.1 Cautions on installation
3.2 Installation diagram
3.3 Installation
4. Troubleshooting 13
12
Car-Solutions.com
[email protected]
www.car-solutions.com

3
1. Input Spec. (MULTI VIDEO INTERFACE)
-. 2 x CVBS Input (External video source).
-. 1 x CVBS (REAR CAMERA) Input (Rear camera source)
-. 1 x Analog RGB Input (Car commander original monitor output)
-. 1 x Analog RGB Input (Navigation System output)-OPTION
2. Output Spec.
-. 1 x CVBS OUTPUT (Video Out for installing Headrest monitor)
-. 1 x RGB OUTPUT(LCD Operation)
-. 1 x Audio Select OUTPUT (For operating A/V sources –ex) 12V is come out on V1 port, when AV1 is chosen.)
3. Power Spec.
- Input Power : 8VDC ~ 18VDC
- Consumption Power : 5WATT, Max
4. Switch Input mode
- NAVI/CVBS1,2 Original MUTE Function : Possible to mute each input by operating Dip S/W
- Possible to switch Input mode with remote control or toggle switch.
- Rear View Camera mode : When to sense rear gear power, be switched to Rear view camera mode
(Impossible to switch to rear mode with Toggle S/W or the Remote control)
1.1 Main Specification
Car-Solutions.com
[email protected]
www.car-solutions.com

4
CVBS
OUT
HEADREST
MONITOR
MCU
VIDEO
CIRCUIT
VIDEO MUX
POWER
CIRCUIT
CVBS 1
CVBS
(Rear Camera)
Power Input
(+8VDC~+18VDC)
DIP S/W
Remote Control Switch for source toggle & REAR SENSE
Navigation Input
(Analog RGB) CAR Installation
OEM LCD
DISPLAY
CVBS 2
CAR SCREEN INPUT
(CAR MAIN BOARD)
1.2 System Diagram
Car-Solutions.com
[email protected]
www.car-solutions.com

1.3 Components
5
RGB NAVI cable * 1ea
SEL cable * 1ea
REMOTE CONTROL * 1ea
INFINITY FX cable * 1ea
IR cable * 1ea
POWER cable * 1ea MODE cable * 1ea
(HIRCAB0002)(HARETC0001)(HPOWER0001)
(REMOTE0001)
(HARETC0003)
(HSELCA0001)
(HNAVIC0002)
Car-Solutions.com
[email protected]
www.car-solutions.com

1.4 Exterior
6
①POWER
②MODE
③IR
④V1
⑤V2
⑥R/V
⑦V-OUT
⑧NAVI (IN)
⑤⑥⑦
⑧
①③④②
⑨⑩⑪⑫⑬
⑨OEM (IN)
⑤⑥⑦①③④②
⑧⑨⑩⑪⑫⑬
⑩RGB OUT
⑪DIP S/W
⑫AUDIO-SEL
⑬LED
Dimension
Horizontal length 129mm
Vertical length 75mm
Height 21mm
Car-Solutions.com
[email protected]
www.car-solutions.com

2.1 DIP switch
7
#PIN Function DIP S/W selection
1 RGB INPUT skip ON : Skipping RGB Mode
OFF : RGB Display
2 CVBS1 MUTE ON : Skipping CVBS1
OFF : CVBS1 Display
3 CVBS2 MUTE ON : Skipping CVBS2
OFF : CVBS2 Display
4 CAN ON : When install to the Cayenne
OFF : When install to all of the car
5 OEM MUTE ON : Skipping OEM
OFF : OEM Display
6 INTERLACE ON : Non-Interlace
OFF : Interlace
7 REAR MODE ON : External Rear Camera
OFF : OEM Rear Camera
8 SYNC ON GREEN ON : Sync On Green (RGSB)
OFF : Sync On Green Off
※DIP S/W Use Example
-. Use Input Mode : CVBS1, Navigation (RGB), Main
-. Rear Camera : When to be installed on CVBS 4
▷DIP S/W : 1 OFF
▷DIP S/W : 2 OFF
▷DIP S/W : 3 ON
▷DIP S/W : 4 OFF (All of the Car except Cayenne)
▷DIP S/W : 5 OFF
▷DIP S/W : 6 OFF
▷DIP S/W : 7 ON (enable CVBS4)
▷DIP S/W : 8 OFF
* Caution
- If the displayed screen vibrates, please try to operate
Dip S/W No. 6 after turning power off.
※Please make sure to disconnect the power cable of the interface and reconnect
the power cable again to apply the dip switch setting whenever changing DIP switch.
Otherwise, DIP switch setting will not be applied.
Car-Solutions.com
[email protected]
www.car-solutions.com

8
2.2 Remote controller
Key Function
POWER & PIP Not for use
MENU Not for use
OK Making a selection
▲Move upward
▼Move downward
◀Move leftward
▶Move rightward
SIZE : 85 * 40 * 8 (mm)
Car-Solutions.com
[email protected]
www.car-solutions.com

2.3 Power cable wiring diagram
9
①GND (검정색)
②I-Drive (오렌지색)
③FMTX안테나
④N.C
⑤ACC(빨강색)
⑥REAR(회색)
⑥⑤④
③②①
Blue
FMTX
I - DRV
GND
LAMP - RV
ACC
990mm
FILTER
& FUSE BOX
주황색
검정색
빨강색
회색
Red
Gray
Orange
Black
파란색
990mm
Car-Solutions.com
[email protected]
www.car-solutions.com

10
3.1 Cautions on installation
Ignition key should be taken off before starting installation, interface power connection must be the last step
in installation.
Power cable should be separated when connecting interface.
Should be no any electronic devices or magnetic pole around installation place.
All steps of installation should be done by well-trained specialist.
Dismantling without manufacturer’s permission can not be guaranteed, (No permission to break attached
label on the board.)
Kindly check all parts are in the box, when receiving the product, if anything missing, inform to the supplier or
manufacturer.
According to our sales policy, any problems caused by user’s mistake, careless can not be guaranteed.
It may not work on a camera with 12V
Car-Solutions.com
[email protected]
www.car-solutions.com