Car Solutions RGB-LE-V3.1 User manual

Your best partner for better driving
Updated date : 2014.02.04
Model : RGB-LE-V3.1 / Product code : RB-100126-013
W164+RGB-LE
Specification & Installation
Car-Solutions.com
[email protected]
car-solutions.com

2
2. Setup
2.1 DIP switch
2.2 Remote controller
2.3 Power cable wiring diagram
7
8
9
3. Installation
10
11
Contents
1. Before installation
1.1 Main specification
1.2 System diagram
1.3 Components
1.4 Exterior
4
3
5
6
3.1 Installation diagram
3.2 Cautions on installation
4. Troubleshooting 12
Car-Solutions.com
[email protected]
car-solutions.com

3
1. Input Spec. (MULTI VIDEO INTERFACE)
-. 2 x CVBS Input (External video source).
-. 1 x CVBS (REAR CAMERA) Input (Rear camera source)
-. 1 x Analog RGB Input (Car commander original monitor output)
-. 1 x Analog RGB Input (Navigation System output)-OPTION
2. Output Spec.
-. 1 x CVBS OUTPUT (Video Out for installing Headrest monitor)
-. 1 x RGB OUTPUT(LCD Operation)
-. 1 x Audio Select OUTPUT (For operating A/V sources –(ex) 12V is come out on V1 port,
when AV1 is chosen.)
3. Power Spec.
- Input Power : 8VDC ~ 18VDC
- Consumption Power : 5WATT, Max
4. Switch Input mode
- NAVI/CVBS1,2 Original MUTE Function : Possible to mute each input by operating Dip S/W
- Possible to switch Input mode with remote control or toggle switch.
- Rear View Camera mode : When to sense rear gear power, be switched to Rear view camera
mode (Impossible to switch to rear mode with Toggle S/W or the Remote control)
1.1 Main Specification
Car-Solutions.com
[email protected]
car-solutions.com

4
CVBS
OUT
HEADREST
MONITOR
MCU
VIDEO
CIRCUIT
VIDEO MUX
POWER
CIRCUIT
CVBS 1
CVBS
(Rear Camera)
Power Input
(+8VDC~+18VDC)
DIP S/W
Remote Control Switch for source toggle & REAR SENSE
Navigation Input
(Analog RGB) CAR Installation
OEM LCD
DISPLAY
CVBS 2
CAR SCREEN INPUT
(CAR MAIN BOARD)
1.2 System Diagram
Car-Solutions.com
[email protected]
car-solutions.com

1.3 Components
5
REMOTE CONTROL * 1ea
GROUND cable * 1ea
Sub-board * 1ea
FPC cable * 1ea
ORANGE cable * 1ea
IR cable * 1ea
POWER cable * 1ea MODE cable * 1ea
(HIRCAB0002)(HARETC0001)(HPOWER0001)
RGB NAVI cable * 1ea
SEL cable * 1ea
(HSELCA0001)
(HNAVIC0002)
(REMOTE0001)
(HNAVIC0003)
(FPCABL0007)
(QCPASS0061)
(HGROUN0001)
Car-Solutions.com
[email protected]
car-solutions.com

1.4 Exterior
6
①POWER
②MODE
③IR
④V1
⑤V2
⑥R/V
⑦V-OUT
⑧NAVI (IN)
⑤⑥⑦
⑧
①③④②
⑨⑩⑪⑫⑬
⑨OEM (IN)
⑤⑥⑦①③④②
⑧⑨⑩⑪⑫⑬
⑩RGB OUT
⑪DIP S/W
⑫AUDIO-SEL
⑬LED
Dimension
Horizontal length 129mm
Vertical length 75mm
Height 21mm
Car-Solutions.com
[email protected]
car-solutions.com

2.1 DIP switch
7
#PIN Function DIP S/W selection
1 RGB INPUT skip ON : Skipping RGB Mode
OFF : RGB Display
2 CVBS1 MUTE ON : Skipping CVBS1
OFF : CVBS1 Display
3 CVBS2 MUTE ON : Skipping CVBS2
OFF : CVBS2 Display
4 CAN ON : When install to the Cayenne
OFF : When install to all of the car
5 OEM MUTE ON : Skipping OEM
OFF : OEM Display
6 INTERLACE ON : Non-Interlace
OFF : Interlace
7 REAR MODE ON : External Rear Camera
OFF : OEM Rear Camera
8 SYNC ON GREEN ON : Sync On Green (RGSB)
OFF : Sync On Green Off
※DIP S/W Use Example
[W211]
-. Use Input Mode : CVBS1, Navigation (RGB), Main
-. Rear Camera : When to be installed on CVBS 4
▷DIP S/W : 1 OFF
▷DIP S/W : 2 OFF
▷DIP S/W : 3 ON
▷DIP S/W : 4 OFF (All of the Car except Cayenne)
▷DIP S/W : 5 OFF
▷DIP S/W : 6 OFF
▷DIP S/W : 7 ON (enable CVBS4)
▷DIP S/W : 8 OFF
* Caution
- If the displayed screen vibrates, please try to operate
Dip S/W No. 6 after turning power off.
Car-Solutions.com
[email protected]
car-solutions.com

2.2 Remote controller
8
Key Function
POWER & PIP Not for use
MENU OSD implementation
OK Making a selection
▲Move upward
▼Move downward
◀Move leftward, press 2 seconds long-Factory
mode implementation
▶Move rightward, press 2 seconds long-Factory
Mode implementation-Factory mode Reset
SIZE : 85 * 40 * 8 (mm)
Car-Solutions.com
[email protected]
car-solutions.com

2.3 Power cable wiring diagram
9
I - DRV
GND
LAMP - RV
ACC
990mm
990mm
FILTER
& FUSE BOX
Orange
Black
Red
Grey
Red
Gray
Orange
Black
Blue
FMTX
Blue
①GND (black)
②I-Drive (orange)
③FMTX antenna
④N.C
⑤ACC(red)
⑥REAR(gray)
⑥⑤④
③②①
Car-Solutions.com
[email protected]
car-solutions.com

10
3.1 Cautions on installation
Ignition key should be taken off before starting installation, interface power connection must be the last step
in installation.
Power cable should be separated when connecting interface.
Should be no any electronic devices or magnetic pole around installation place.
All steps of installation should be done by well-trained specialist.
Dismantling without manufacturer’s permission can not be guaranteed, (No permission to break attached
label on the board.)
Kindly check all parts are in the box, when receiving the product, if anything missing, inform to the supplier or
manufacturer.
According to our sales policy, any problems caused by user’s mistake, careless can not be guaranteed.
Car-Solutions.com
[email protected]
car-solutions.com