Car Solutions QHI-LVTX(HH)-MAIN-V3.0 User manual

Car-Solutions.com
[email protected]
car-solutions.com

•Specification
Car Compatibility : 2017 Infinity Q30
Components : Interface* 1ea, Sub-board*1ea
Multimedia interface Input/output spec
Input : HDMI*2, Analog RGB*1, A/V*1,
CVBS(Rear view Camera)*1, CVBS(Front camera)*1
Output : To LCD*1
Power spec
Input power : 8VDC ~ 18VDC
Consumption : 5WATT
Switch input mode
External video sources skip function : able to control input
videos on and off via DIP switches.
Able to switch videos via the remote, button switch, and
original buttons.
Able to detect the rear view camera (back up camera)
via Lamp or CAN.
2
•Features
Able to output high resolution video via HDMI input
Control external videos sources (DVD, DTV) via Multi Media
Touch
Adjust external videos screen position
Check the improved Screen Display (User Friendly Interface)
Switch modes via original OEM button
Supply power to connect rear view camera (Back up
camera)
Assist your parking via Dynamic PAS(Parking Assistance
System). It displays the moving parking line according
movement of steering wheel
Car-Solutions.com
[email protected]
car-solutions.com

3
•Product Exterior
•Components
AV * 1ea
(HAVCAB0056)
RGB * 1ea
(HRGBCA0026)
BUTTON * 1ea
(HARETC0001)
IR * 1ea
(HIRCAB0002)
REMOTE * 1ea
(REMOTE0001)
LVDS * 1ea
(HLVDSC0058)
POWER * 1ea
(HPOWER0161)
FFC cable * 2ea
(FFCBAL0081)
(FFCBAL0084)
서브보드 * 1ea
(QCPASS1015)
MULTI * 1ea
(HARETC0240)
SEL * 1ea
(HARETC0250)
TAPE * 1ea
(LABELS0211)
REAR * 1ea
(HARETC0002)
Car-Solutions.com
[email protected]
car-solutions.com

PIN Function Dip S/W
1 RGB INPUT MUTE OFF : RGB DISPLAY
ON : Skipping RGB Mode
2 HDMI1 MODE MUTE OFF : HDMI1 DISPLAY
ON : Skipping HDM1 Mode
3 AV MODE MUTE OFF : AV DISPLAY
ON : Skipping AV Mode
4 FRONT CAM MUTE OFF : Front camera function on
ON : Front camera function off
5 NO USE(OFF)
6
7 REAR CAM MODE OFF : OEM Rear Camera
ON : External Rear Camera
8 NO USE(OFF)
※ ON : DOWN / OFF : UP
4
•DIP SWITCH
※Please make sure to disconnect the power cable of the interface and
reconnect the power cable again to apply the dip switch setting whenever
changing DIP switch. Otherwise, DIP switch setting will not be applied.
•REMOTE CONTROL SETTING
Car-Solutions.com
[email protected]
car-solutions.com

5
•Factory setting
Adjust a current screen position and size.
PAS TYPE : Select type of parking guide line
- NOT USED : No use parking guide line
- PAS ON : Selecting Dynamic parking guide line
- PAS OFF : Selecting fixed parking guide line
REAR TYPE : Choose rear camera recognition.
- CAN : By connecting to “CAN” cable of the car gear, changing to
rear camera mode when shifting into reverse. (Connect “CAN”
cable of the power cable to the “CAN” cable of the car gear.)
- LAMP : By connecting to the rear lamp of the car, switch to rear
camera mode when shifting into rear. (Connect “Rear-C” cable of
the power cable to the rear lamp of the car.)
SAFE ENABLE : If it is enable, HDMI, RGB, and A/V mode doesn’t show up
while driving. (Default : OFF)
PAS SETUP : Adjusting the position of the parking guide line
<H-POSITION> <V-POSITION>
Adjust rear view camera setting.
H-POSITION : Move display horizontally
V-POSITION : Move display vertically
BRIGHTNESS : Adjust brightness of screen
CONTRAST : Adjust contrast of screen
Car-Solutions.com
[email protected]
car-solutions.com

6
NAVI MODEL : Setting up RGB Navigation.
(Default, Q-roi RGB, WP9230,
HDMI(WVGA))
HDMI MODEL : Setting up HDMI1 Navigation.
(Q-roi RGB, WP9320)
CAR MODEL :Q30
HDMI2 SKIP : Skipping HDMI mode when
switching modes.
AVOUT SELECT : Selecting background sound
through car AUX.
(HDMI1, HDMI2, AV)
Navigation & Car model setting up
•Factory setting
Other options setting up
•CALIBRATE : Able to calibrate touch screen
•REMOTE SELECT : Able to use remote control on
DVD, DTV by selecting “User”
after IR memory registered.
(Default, User)
•HD2 REMOTE OSD : HDMI2 OSD on or off
•AV REMOTE OSD : AV OSD on or off
•IR MEMORY : Registering IR memory
(Remote control values) of DTV,
DVD.
•FACTORY RESET : Factory mode reset.
System version information
Car-Solutions.com
[email protected]
car-solutions.com

7
•OEM button
Long Press : Mode switch
Short Press: OEM mode
Car-Solutions.com
[email protected]
car-solutions.com

8
LVDS Cable
•Installation Diagram
RGB
NAVI BOX
HDMI
NAVI BOX
Monitor backside
Power cable
OEM cable
1 ※ Remove OEM cable from connector of monitor
behind and connect OEM cable to supplied power
cable the other side of supplied connector shall be
connected to connector
1
1
※HDMI NAVI
must be connected
to HDMI-1.
Mirroring
Device
5V
HDMI
NAVI BOX
RGB
NAVI BOX
A
U
D
I
O
(R)
O
U
T
A
U
D
I
O
(L)
O
U
T
F
C
A
M
A
U
D
I
O
(R)
IN
1
A
U
D
I
O
(L)
IN
1
R
C
A
M
V
I
D
E
O
IN
1
V
I
D
E
O
O
U
T
1
V
I
D
E
O
O
U
T
2
A
U
D
I
O
(R)
IN
2
A
U
D
I
O
(L)
IN
2
V
I
D
E
O
IN
2
A/V CABLE
R
C
A
M
S
A
F
E
R
E
A
R
V
1
I
R
V
2
I
R
R
E
M
O
T
E
T
O
G
G
L
E
12
V
S
E
L
F
C
A
M
12
V
MULTI CABLE
Car-Solutions.com
[email protected]
car-solutions.com

6. Installation
6.4 Subboard installation
Disassemble the monitor from
Q30 as shown above
Remove the metal cover
on the top
Disassemble the PCB board Remove the metal cover again
Disassemble PCB board
except OEM FPC cables
Make marked hook flat
Car-Solutions.com
[email protected]
car-solutions.com

6. Installation
6.4 Subboard installation
OEM FPC cables and
supplied LVDS cables shall be
connected to the subboard
After attaching a double sided tape on the back of
the subboard, Peel away the back of the tape.
Fix the subboard on the metal surface and
connect supplied FFC cables to the subboard
The opposite side of supplied
FFC cables should be
connected to the place where
OEM FPC cables are
connected
Place the board on the top of the metal
case and reassemble the rest parts
Car-Solutions.com
[email protected]
car-solutions.com

Q. I cannot change mode
A. Check connection of Ground cable and IR Cable. Check LED lamp
is on, if not check connection of POWER cable.
Q. All I got on the screen is black.
A. Check second LED lamp of the interface is on, if not, check A/V
sources connected are working well. (Second
lamp indicates AV sources connected works well.) Check interface
connection has been done well.
Q. Displayed image color is not proper (too dark or unsuitable color)
A. Press ▶button on the remote control for 2 seconds and check how
it goes, if it does not work, inform to manufacturer.
Q. I cannot watch the rear camera on the screen
A. Set the DIP switch #7 as state “ON”.
Q. Set mode not appear
A. Check DIP Switch.
Q. OEM image is not displayed.
A. Check interface’s LCD In/Out cable connection. If the status keeps
on, inform to manufacturer.
Q. Screen only displays white color.
A. Check LCD out cable is connected well, if this status keeps, inform to
manufacturer.
Q. If the original screen is shown half only after using the handle button
for running the PIP function.
A. This is not because of defect but incorrect setting up. Make sure to
set up the original monitor function as “split screen”
Q. If no image is shown on screen after connecting CAN wire with Park
gear.
A. Go on the “FACTORY MODE”, check “UTIL-Rear Select”. If “LAMP”,
change the setting as “CAN” with the remote control. (※when
connecting Rear-C wire of LAMP power cable to Backup lights, Setting
should be like this / CAN : if controlling rear camera with CAN wire)
11
•Trouble shooting
Car-Solutions.com
[email protected]
car-solutions.com