Car Solutions qpi-lvtx-astm User manual

Updated date : 2015.11.10
Model : RGB-LE-V4.0
RGB-LE CONVERTER
Specification & Installation
Car-Solutions.com
[email protected]
www.car-solutions.com

2
2. Setup
2.1 DIP switch
2.2 Remote controller
2.3 Power cable wiring diagram
7
8
9
3. Installation
10
11
Contents
1. Before installation
1.1 Main specification
1.2 System diagram
1.3 Components
1.4 Exterior
4
3
5
6
3.1 Cautions on installation
3.2 Installation diagram
4. Troubleshooting 12
Car-Solutions.com
[email protected]
www.car-solutions.com

3
1. Input Spec. (MULTI VIDEO INTERFACE)
-. 2 x CVBS Input (External video source).
-. 1 x CVBS (REAR CAMERA) Input (Rear camera source)
-. 1 x Analog RGB Input (Car commander original monitor output)
-. 1 x Analog RGB Input (Navigation System output)-OPTION
2. Output Spec.
-. 1 x CVBS OUTPUT (Video Out for installing Headrest monitor)
-. 1 x RGB OUTPUT(LCD Operation)
-. 1 x Audio Select OUTPUT (For operating A/V sources –(ex) 12V is come out on V1 port,
when AV1 is chosen.)
3. Power Spec.
- Input Power : 8VDC ~ 18VDC
- Consumption Power : 5WATT, Max
4. Switch Input mode
- NAVI/CVBS1,2 Original MUTE Function : Possible to mute each input by operating Dip S/W
- Possible to switch Input mode with remote control or toggle switch.
- Rear View Camera mode : When to sense rear gear power, be switched to Rear view camera
mode (Impossible to switch to rear mode with Toggle S/W or the Remote control)
1.1 Main Specification
Car-Solutions.com
[email protected]
www.car-solutions.com

4
CVBS
OUT
HEADREST
MONITOR
MCU
VIDEO
CIRCUIT
VIDEO MUX
POWER
CIRCUIT
CVBS 1
CVBS
(Rear Camera)
Power Input
(+8VDC~+18VDC)
DIP S/W
Remote Control Switch for source toggle & REAR SENSE
Navigation Input
(Analog RGB) CAR Installation
OEM LCD
DISPLAY
CVBS 2
CAR SCREEN INPUT
(CAR MAIN BOARD)
1.2 System Diagram
Car-Solutions.com
[email protected]
www.car-solutions.com

1.3 Components
5
RGB NAVI cable * 1ea
IR cable * 1ea
POWER cable * 1ea MODE cable * 1ea
SEL cable * 1ea
REMOTE CONTROL * 1ea
RGB OUT cable (8P) * 1ea RGB OEM cable(5P) * 1ea
(HIRCAB0002)
(REMOTE0001)
(HNAVIC0002)
(HRGBCA0003)
(HARETC0001)(HPOWER0001)
(HSELCA0001) (HRGBCA0002)
Car-Solutions.com
[email protected]
www.car-solutions.com

1.4 Exterior
6
①POWER
②MODE
③IR
④V1
⑤V2
⑥R/V
⑦V-OUT
⑧NAVI (IN)
⑤⑥⑦
⑧
①③④②
⑨⑩⑪⑫⑬
⑨OEM (IN)
⑤⑥⑦①③④②
⑧⑨⑩⑪⑫⑬
⑩RGB OUT
⑪DIP S/W
⑫AUDIO-SEL
⑬LED
Dimension
Horizontal length 129mm
Vertical length 75mm
Height 21mm
Car-Solutions.com
[email protected]
www.car-solutions.com

2.1 DIP switch
7
* Caution
- If the displayed screen vibrates, please try to
operate Dip S/W No. 6 after turning power off.
※Please make sure to disconnect the power
cable of the interface and reconnect the power
cable again to apply the dip switch setting
whenever changing DIP switch.
Otherwise, DIP switch setting will not be applied.
#PIN Function DIP S/W selection
1 RGB INPUT skip ON : Skipping RGB Mode
OFF : RGB Display
2 CVBS1 Skip ON : Skipping CVBS1
OFF : CVBS1 Display
3 CVBS2 Skip ON : Skipping CVBS2
OFF : CVBS2 Display
4 OEM Skip ON : Skipping OEM
OFF : OEM Display
5
OEM Button
Usage
5-OFF, 6-OFF : E-Class(W211)
5-OFF, 6-ON : PHAETON
5-ON, 6-OFF : CAYENNE
5-ON, 6-ON : BENZ W164
6
7 REAR MODE ON : External Rear Camera
OFF : OEM Rear Camera
8 No use OFF: Default
Car-Solutions.com
[email protected]
www.car-solutions.com

2.2 Remote controller
8
Key Function
PIP RESET –long press
MENU Not for use
OK Making a selection
▲Display brightness higher
▼Display brightness lower
◀Chroma higher
▶Chroma lower
SIZE : 85 * 40 * 8 (mm)
Car-Solutions.com
[email protected]
www.car-solutions.com

2.3 Power cable wiring diagram
9
I - DRV
GND
LAMP - RV
ACC
990mm
990mm
FILTER
& FUSE BOX
Orange
Black
Red
Grey
Red
Gray
Orange
Black
Blue
FMTX
Blue
①GND (black)
②I-Drive (No use)
③FMTX antenna
④N.C
⑤ACC(red)
⑥REAR(gray)
⑥⑤④
③②①
Car-Solutions.com
[email protected]
www.car-solutions.com

10
3.1 Cautions on installation
Ignition key should be taken off before starting installation, interface power connection must be the last step
in installation.
Power cable should be separated when connecting interface.
Should be no any electronic devices or magnetic pole around installation place.
All steps of installation should be done by well-trained specialist.
Dismantling without manufacturer’s permission can not be guaranteed, (No permission to break attached
label on the board.)
Kindly check all parts are in the box, when receiving the product, if anything missing, inform to the supplier or
manufacturer.
According to our sales policy, any problems caused by user’s mistake, careless can not be guaranteed.
It may not work on a camera with 12V
Car-Solutions.com
[email protected]
www.car-solutions.com