Charlton & Jenrick Solstice User manual

1
Operating Manual
for Integral Electrical Appliance
Models: Solstice and Equinox
Please read the instructions carefully before installation or use
of this electric fire and retain for future reference.
This product is made by
Supplied under licence to
FDC (UK) Limited
Unit C4, Dinton Business Park
Catherine Ford Road
Dinton
Salisbury
SP3 5HZ
01722 716161
[email protected]

2
IMPORTANT INFORMATION
This appliance must not be located immediately below a socket-outlet.
This appliance must be earthed. If in any doubt consult a suitable competent
person.
In order to avoid a hazard due to inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through an external switching device, such
as a timer, or connected to a circuit that is regularly switched on and off by a
utility company.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless under supervision of a person responsible for their safety.
Children should not play with the appliance.
The fuel bed includes some small glass pebbles which could be harmful to
children if swallowed. It is recommended that these are not used if children can
access this appliance.
Cleaning and maintenance should only be carried out by a competent person.
Some parts of this product can become very hot and cause burns. Particular
attention has to be given where children and vulnerable people are present.
It is recommended that a fireguard should be used for the protection of children,
the elderly and infirm. Fireguards should conform to BS 6539 (1984)
(Fireguards for use with solid fuel appliances).
Do not use this fire as a free-standing appliance. It must always be fixed to a
wall or in a fireplace mantel.
WARNING: Do not cover the heater.
If the supply cord is damaged, it must be replaced by a genuine part available
from the manufacturer or its service agent.

3
APPLIANCE DATA
Supply Voltage AC 220-240V 50Hz
Output 1000W / 2000W
DIMENSIONS
SOLSTICE units: mm
EQUINOX units: mm
PARTS LIST
Part
Quantity
Appliance
1
Fuel Bed
1
Remote Control
1
AAA Battery
2
Instruction Manual
1
Fixing Bracket
2
Screw ST4*12
8
Washer 4.0
4

4
INSTALLATION
Choosing the position of your Electric Fire
Your new electric fire may be installed virtually anywhere in your home. When choosing a
location ensure that the general instructions are followed. For best results, install out of direct
sunlight.
WARNING! Ensure curtains and other combustible furnishings are kept at least
3ft/0.9m from the front of the electric fire.
The appliance can be installed in a number of different ways.
1. Incorporated in a marble, stone or timber fireplace.
2. Set into an external cavity wall when using a fire surround with a 3” rebate.
3. Set into an existing chimney breast with a stone or marble fascia.
4. Set into a false chimney breast with a stone or marble fascia.
Typical construction of a false chimney breast
1. Position and construct a framework as shown in figure 1.
2. Allow sufficient width to accommodate your chosen fireplace and bear in mind that the
opening may need to be raised to suit the fireplace.
3. If being used with a stone or marble fascia it is important to allow for the thickness of the
fascia when fixing the depth of the appliance in the opening
4. Fix the appliance in the opening using the brackets supplied and level with shims if required.
5. The chimney breast may be clad in combustible or non-combustible materials.
Figure 1
General installation considerations and guidance
Where the appliance is fitted into an existing chimney breast or into an external wall cavity, then
consideration should be given to ensure the appliance is protected from the risk of the ingress
of water. This may be done by blocking the chimney or the cavity with rock wool tightly packed
into the void around and to the rear of the appliance or providing a suitable membrane to
protect the metal casing of the appliance. Ensure the vents on the top and sides of the
appliance are not obstructed and can access free air.
This appliance can be installed via a fused spur or 13 Amp plug. The location of both must be
accessible for isolation.
MODEL
W
D
H
SOLSTICE
630
225
625
EQUINOX
895
225
675

5
Laying the fuel bed
The fuel bed components are packed in a separate carton, please open this carefully as the
log shapes are fragile. Please notify us immediately if any of these shapes are damaged.
They are not covered by any warranty after they have been checked by the customer and
accepted as complete and undamaged. New fuel bed sets are available to purchase from FDC
(UK) Ltd. Also in the carton are some glass pebbles and a bag of loose vermiculite.
The glass pebbles could be harmful if swallowed, so please keep out of reach of children
and we recommend you don’t use them on the appliance if you consider there is any risk
of a child coming in contact with them.
There is no recommended layout for the fuel bed. It is entirely up to the customer to create their
own desired layout and finished look. Using the supplied fuel bed use as many or as few logs
as you wish. We recommend you lay the vermiculite on the chrome plate of the fire in a thin
layer leaving small areas on the chrome surface un-covered. Position the logs as you wish and
if you choose to use the glass pebbles place them randomly around and between the logs.
Examples are shown below;
Typical Fuel bed arrangement for Solstice
Typical Fuel bed arrangement for Equinox

6
OPERATION
This appliance can be operated by both remote control and manual buttons. Once the unit has
been properly connected to an earthed electrical outlet turn on the main switch. A beep should
be heard when the power is first applied.
NOTES:
To use both remote and manual functions the main on/off switch must be in the
‘on’ position.
The flame will always be on when the appliance is on.
In order to protect the product from becoming too hot, there is an 8 second delay
when turning on the heater. There is also an 8 second delay when turning off the
heater.
●Operating by Manual Button
Main switch
Heater button
Flame button
NOTE：
Main switch
This switch must be in the “ON” position for any of the functions including the remote to work.
Flame button
By pressing the FLAME button, the unit will cycle through four flame effects.
Heater button
Pressing once turns the fan on and 8 seconds later the low heat comes on. (Pilot lights
illuminated ●○) Pressing again turns on the high heat. (Pilot lights illuminated ●●)
Pressing third time turns the heat off. 8 seconds later the fan switches off (Pilot lights
illuminated ○○)

7
●Operating by Remote Handset
Multifunction Infrared Remote Handset
Make sure the batteries are installed properly in the remote control.
The effective range of the remote control is up to 4 meters or 13 feet.
ICON
TITLE
FUNCTION
POWER
Pressing once turns the appliance and
flame effect on. Pressing again turns the
appliance and flame effect off.
FLAME
The fire has four flame effects, by pressing
the flame effect button the unit will cycle
through each effect.
HEATER
Pressing once turns 1000W of power on.
(Pilot lights illuminated ●○)
Pressing again turns 2000W of power on
(Pilot lights illuminated ●●)
Pressing third time turns the heater off.
(Pilot lights illuminated ○○)
ROOM TEMP /
THERMOSTAT
Digital display shows a default TEMP
setting. To set the desired room temp press
the button and the TEMP will increase by
1°C up to 28°C when pressed each time.
The heater will cut out automatically once
the desired temperature is reached.
By pressing this button for 3 seconds the
digital display can change between °C and
°F.
TIMER
Once the appliance has been turned on,
you can program a length of time you would
like the appliance to run. Cycles from
TIMER OFF, 0.5H, 1H, 2H, 3H, 4H, 5H, 6H,
7H, 8H, to 9H.

8
MAINTENANCE
Warning: Before any maintenance and/or cleaning of the exterior of the fireplace,
disconnect the unit from the power supply and leave until cool.
Remote Handset Battery Replacement
Replace with two AAA batteries. Make sure the batteries are installed correctly in the
remote control.
Maintenance of Motors
The motors used on the fan and flame effect are pre-lubricated for extended bearing
life and require no further lubrication. However, periodic cleaning/vacuuming of the
fan/heater unit is recommended.
Resetting the Thermal Cut-out Switch
The appliance is fitted with an Electronic Safety Control (E.S.). This is a safety device,
which switches off the fire if, for any reason, the appliance overheats e.g. when
covered. If the heater stops operating whilst the flame effect continues normally this
could indicate that the E.S. Control is in operation. The E.S. Control can only be re-set
after the appliance has cooled down, in order to re-set the E.S. Control proceed as
follows:
Switch off the appliance (Main On/Off switch) and leave for approximately 10-
15 minutes.
Remove any obstruction to the fan heater outlet or fan blades etc. Make sure
that the power supply is disconnected at the plug socket outlet whilst you do
this.
Switch on the appliance and the E.S. Control will re-set.
Ensure that the appliance is functioning correctly. If the E.S. Control operates
again, the appliance should be checked by a competent Electrician.
Cleaning the Appliance
To remove fingerprints or other marks on the front glass panel, use a soft, damp, lint-
free cloth with a good quality household glass cleaner. The front glass panel should
always be completely dried with a clean, lint-free cloth or paper towel.
Caution: Do not use abrasive cleaners on the glass panel. Do not spray
liquids directly onto any surface of the unit.
Warning: An authorised service representative should perform any other
servicing.
Environment Do not dispose of electrical appliances as unsorted municipal waste,
use separate collection facilities. Contact your local council for
information regarding the collection systems available. If electrical
appliances are disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and get into the food
chain, damaging your health and well-being. When replacing old
appliances with new ones, the retailer is legally obligated to take
back your old appliance for disposal free of charge.